Construction Of Garage With Temporary Roof Shed For The Vehicle Used For Swm Project At Charak Tala Garifa In Ward No-05,Under Naihati Municipality.
Tender Value
11.08 Lakhs
Estimated cost
Bid Submission
15 Feb 2025
0 days left
EMD
22160
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
naihati → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Garage With Temporary Roof Shed For The Vehicle Used For Swm Project At Charak Tala Garifa In Ward No-05,Under Naihati Municipality.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.(a) Depth of excavation not exceeding 1,500 mm. |
| 2 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm.including watering and ramming etc. layer by layercomplete. (Payment to be made on the basis of measurement of finished quantity of work) |
| 3 | (c) (i) With carried earth arranged by the contractorwithin a radius of 1 km. including cost of carried earth. |
| 4 | (a) With earth obtained from excavation of foundation |
| 5 | Filling by silver sand in layers not exceeding 150 mm as directed and consolidating the same by through saturation with water, ramming complete including the cost of supply of sand. |
| 6 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 7 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes.a) Pakur Variety |
| 8 | Brick work with 1st class bricks in cement mortar (1:6) (a) In foundation and plinth |
| 9 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. |
| 10 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](ii) With 1:6 cement mortar(b) 15 mm thick plaster |
| 11 | (ii) With 1:6 cement mortar(b) 20 mm thick plaster |
| 12 | Neat cement punning about 1.5mm thick in wall,dado,window sill,floor etc.NOTE:Cement 0.152 cu.m per100 sq.m. |
| 13 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge-black annealed wire at every intersection, complete as per drawing and direction. (a) For works in foundation, basement and upto roof of ground floor/upto 4 m. (i) Tor steel/Mild Steel. (i) In Foundation |
| 14 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor). |
| 15 | Ordinary Cement concrete (mix 1:1.5:3) withgraded stone chips (20 mm nominal size)excluding shuttering and reinforcement ifany, in ground floor as per relevant IS codes(i) Pakur Variety(ii) In Ground Floor |
| 16 | Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. In ground floor. 3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement). Using grey cement (iii) 35 mm. thick.In Ground Floor |
| 17 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured(matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC. |
| 18 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer\"s specification and as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. (i) Normal Acrylic Emulsion |
| 19 | (a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 20 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : |
| 21 | (b) On steel or other metal surface :With super gloss (hi-gloss) - |
| 22 | (iv) Two coats (with any shade except white) |
| 23 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by syntheticadhesive & grout materials etc. |
| 24 | (A) FloorWith Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.(a) Area of each tile upto 0.09 Sq.m(i) Coloured decorativ |
| 25 | (B) Wall With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (a) Area of each tile upto 0.09 Sq.m (i) Coloured decorative |
| 26 | M.S. structural works with hollow sections (square or rectangular shape) conforming to IS: 806-1968 & IS:1161-1998) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoistingand erection all complete. The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete.i) For roof truss worksa) Span up to 12 Mtr |
| 27 | Labour for hoisting and placing in proper position (up to 1st floor level) departmental R.S. joists, channels, angles. Tees, plates etc. including fitting and fixing same with bolts and nuts, if necessary (but excluding cost of such bolts and nuts) |
| 28 | Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugation minimum side lap. (Payment to be made on area of finished work)(GCI sheet to be supplied by contractor)(i) In Roof:-a) With 0.60 mm thick sheet. |
| 29 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete. |
| 30 | A) UPVC Pipes: |
| 31 | (ii) 110 mm. Dia. |
| 32 | B) UPVC Fittings: |
| 33 | c) Bend 87.5 degree |
| 34 | ii) 110 mm. Dia |
| 35 | Galvanised iron sheet ridging fitted with necessary bolts, screws, washers etc complete.(225mm end lapping)(A) 300 mm lapping each way(a) With 0.60 mm sheet |
| 36 | Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting,fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately). |
| 37 | (A) For Exposed Work.[(Ref. Sche. Sanitation & Plumbing, P-2,It. No.1)]. |
| 38 | ( c). (ii) 25 mm dia. medium quality |
| 39 | ( f ). (ii) 50 mm dia. medium quality |
| 40 | (B) For Concealed Work :(i) 15 mm dia. medium quality. |
| 41 | (iii) 25 mm dia. medium quality. |
| 42 | Supplying, fitting & fixing Bib Cock or stop cock : [(Ref. Sche. Sanitation & Plumbing, P-6,It. No.7)]. |
| 43 | (ii) Chromium plated Bib Cock long body with wall flange with aerator (Equivalent to Code No. 512 & Model - Tropical / Sumthing Special of ESSCO or similar brand) |
| 44 | ( b ) (ii) Chromium plated Concealed Stop Cock (Equivalent to Code No. 514(A) & Model - Tropical / Sumthing Special of ESSCO or similar brand). |
| 45 | Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer. [(Ref. Sche. Sanitation & Plumbing, P-37,It. No.6)]. |
| 46 | (b) 1000 litre capacity. |
| 47 | (d) 2000 litre capacity |
| 48 | Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approvedquality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint. |
| 49 | iii) 630 mm X 450 mm size [(Ref. Sche. Sanitation & Plumbing, P-41,It. No.2)]. |
| 50 | Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia. |
| 51 | (v) 900 mm long. [(Ref. Sche. Sanitation & Plumbing, P-43,It. No.9)]. |
| 52 | Supplying, fitting & fixing Cast iron soil pipe only conforming to I.S. 3989/ 2009 and I.S. 1729/2002 with bobbins, nails etc. including making holes in the wall, floor etc. and cutting trenches etc. in any floor through masonry concrete, if necessary, and mending good damages with necessary jointing materials and painting two coats to the exposed surface with approved paint complete. (Measurement will be made along the center line of the total pipe line in fitted condition including specials,payment for specials & Painting will however be paid seperately). (a) With valamoid joints including sealing with sand cement morter (4:1) upto quarter depth. [(Ref. Sche. Sanitation & Plumbing, P-60,It. No.1)]. |
| 53 | i) 150 mm dia. (internal) |
| 54 | (b) With lead caulked joints.(i) 150 mm dia. (internal) |
| 55 | Supplying,fitting and fixing cast iron \"P\" or \"S\" trap conformimg to I.S. 3989/ 2009 and 1729/ 2002 including lead caulked joints and painting two coats to the exposed surface. (Painting to be paid seperately. [(Ref. Sche. Sanitation & Plumbing, P-65,It. No.14)]. |
| 56 | v) 150 mm |
| 57 | Supplying, fitting and fixing Anglo-Indian W.C. in white glazed vitreous china ware of approved make complete in position with necessary bolts, nuts etc.(a) With \"P\" trap (with vent).[(Ref. Sche. Sanitation & Plumbing, P-79,It. No.3)]. |
| 58 | Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete.[(Ref. Sche. Sanitation & Plumbing, P-80,It. No.6)]. |
| 59 | i) 635 mm X 395 mm X 420 mm |
| 60 | Supplying, fitting and fixing Squating plate with integral flushing in white vitreous chinaware of approved make in cement concrete (6:3:1) with jhama chips complete. (Payment of concrete will be paid seperately). (i) 450 mm X 350 mm. |
| 61 | Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete. [(Ref. Sche. Sanitation & Plumbing, P-81,It. No.10)]. |
| 62 | (b) Anglo Indian. (ii) Plastic (hallow type) white |
| 63 | Supplying, fitting and fixing urinal flush pipe fittings of approved brand. [(Ref. Sche. Sanitation & Plumbing, P-81,It. No.12]. |
| 64 | (b) C.P. urinal flush pipe fittings range of two |
| 65 | Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm. [(Ref. Sche. Sanitation & Plumbing, P-81,It. No.19)]. |
| 66 | (ii) 600 mm X 450 mm |
| 67 | Supplying, fitting and fixing towel rail with two brackets. [(Ref. Sche. Sanitation & Plumbing , P-81, It. No.22)]. |
| 68 | (b) Aluminium. (iii) 25 mm dia. and 750 mm long. |
| 69 | Supplying, fitting and fixing porcelain soap tray of approved make.(i) Recessed soap tray of size 150 mm X 150 mm.[(Ref. Sche. Sanitation & Plumbing , P-83, It. No.24)]. |
| 70 | Supplying, fitting and fixing PVC pipes for underground work of approved make of Schedule 80 (medium duty) conforming to ASTMD -1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross,elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc.fitted including cost of all materials ,jointing materials, cutting pipes,making threads ,cutting trenches upto 1.5 metre below surface in all sortsof soil and refilling the same as directed complete in all respect. (Paymentwill be made on the centre line measurement of the total pipe lineincluding all specials No separate payment will be made for accessories,specials.)PVC Pipes.(Dia).[ Ref.PWD Sch.S & P,P.No.13, It.No.19(II) ]. |
| 71 | 15 mm |
| 72 | 25 mm |
| 73 | Supplying, Fitting & Fixing 30 mm thick thick both side prelaminated Double Leaf Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail.Top,bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th. both side PVCsheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in-Charge.In ground floor. [ Ref. PWD Sch,P.No.128 , It.No. 18 ]. |
| 74 | Supplying, fitting & fixing factory made foam PVC (density shall not be less than 600 kg/cum) door frame (finished weight of 2.73 kg/mtr.) of size 100mm X 45mm made off with 5mm thick extruded foam PVC sheet, mitre cut at junction of horizontal and vertical member and joined them by heat welding. Entire door frame profiles to be reinforced with steel primer coated 19 SWG 40mm X 20mm M.S. tube. An additional 5mm thick PVC sheet with desired colour/shade to be provided at the exposed surface and three nos 5mm thick PVC sheet to beprovided as gap insert. The door frame to be fixed with wall by using 8mm dia.and 100mm long strainless steel screws and PVC fasteners. A minimum of 4 nos.screws to be provided for each vertical member & 2 nos. for horizontal memberall complete as per direction of Engineer-in-Charge.P.No.128.I-No-19. |
| 75 | Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x10mm x 2mm vertical channels 100mm apart in fully stretched position 20mm x 5mm M.S. flats as collapsible bracings properly rivetted and washered including 38mm steel rollers including locking arrangements, fitted and fixed in position with lugs set in cement concrete and including cutting necessary holes, chasing etc. in walls, floors etc. and making good damages complete.P=80.I=15. |
| 76 | Construction of septic tank of different capacities as per approved drawing with 1stclass brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manholecover(heavy type)of approved make supplied, fitted and fixed in the 100mm thickR.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1)with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1)to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick .C.C(1:1.5:3) bottom slab including supplying, fitting andfixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavationearth in all sorts of soil, shoring, bailing out and pumping out water as necessary,ramming, dressing the bed and fefilling the sides of the tanks with earth, emovingspoils, filling up the chamber with clear water, removing foreign materials from thechamber and including constructing attached inspection pit as per approved drawingand connecting all necessary pipes, joints etc. with internal plaster work and artificialstone flooring is to be done with admixture of water proofing compound @ 0.5% byweight of cement with all costs of labour and materials. Note:- (i) Finished level ofSeptic Tank should be 400 mm. from Ground Level. (ii) Height of 50 mm.Ventilation pipe &Mosquito proof mesh, should be follwed as per IS:2470,Part I.Payment will be made separetly on the basis of actual height based on relevantI.S.Code.(vi) For 200 usersA) With Pakur variety. (SAIL/TATA/RINL) page no 88 item no 03 (vi)(A) |
| 77 | Add 18% GST |
| 78 | Add 1% CESS |
AI Tender Summary
Tender Timeline
Jan 28, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedFeb 15, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedFeb 17, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender