Educational and Research Institute Boards / Undertakings / PSU Closing in 0 days TDR #47395938

Tender For Construction Work At Govt. Senior Secondary School Rulyana Patti Block Nechhwa Dist. -Sikar - Mp Lad 2023-24 Construction Toilet Work At Govt. Senior Secondary School Rulyana Patti , Block-Nechhwa Dist-Sikar Sl. No. Item Description 1 P

Issued by Boards / Undertakings / PSU · patti, Rajasthan
Tender Value
3.85 Lakhs
Estimated cost
Bid Submission
30 Jan 2025
0 days left
EMD
7700
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
patti → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender For Construction Work At Govt. Senior Secondary School Rulyana Patti Block Nechhwa Dist. -Sikar - MP LAD 2023-24 CONSTRUCTION TOILET WORK AT GOVT. SENIOR SECONDARY SCHOOL RULYANA PATTI , BLOCK-NECHHWA DIST-SIKAR Sl. No. Item Description 1 Part-A : Civil WorkBased on BSR 2022, PWD Rajasthan 2 Construction to tube well from ground levels and upto 100 meter depth and above to accommodate housing and assembly pipe of following sizes in all types of alluvium strata by percussion/ rotary drilling method and with gravel as per IS : 4097-1967 and packing as per IS : 2800 ( Part I & II ) 1979 as amended upto date ( the work includes the cost of gravel & its primary packing and packing during development. lowering of housing & strainer assembly pipes, with supply and wrappiing of coir rope, wherever necessary, for arresting fine sand particles. The work will not include cost of housing pipe and strainer pipe assembly and development work, but work would be completed after obtaining sand free water.) 3 150 mm Nominal Bore. 4 Construction ofTube well upto 100 meter depth and above in all type of rocks by DTH system and over burden, to accommodate casing pipe of following sizes in all types of soils and over burden including lowering of casing pipes, but excluding cost of casing pipes as per IS : after obtaining sand free water. The tube well should have a throughout bore as per nominal dia of casing pipe. 5 150 mm Nominal Bore. 6 Development of tube well as per ISI specification using suitable compressor to give free water for required yield of the gravel packed tube well. 7 Supply fo ERW M.S. black casing pipe ISI marked ( IS : 4270/1992) of grade Fe410 of following sizes at site of work. Nominal bore of pipe (mm) 8 150 mm nominal boae of pipe 9 Supply of strainer pipes made of ERW M.S. black pipe ISI mark of following sizes at the site of work including required size fo slotting as pe IS: 8110 1985 10 150 mm nominal boae of pipe 11 Testing verticality of tube well by plumbing system and yield test and draw test by pumping system as per IS : 2800 (Part II) 1979. 12 S & F tube well cover fo M.S. sheet (6mm thick) with nuts and bolts complete forsize. 13 150 mm dia 14 S & F M.S. Clamp, set of 50 X6 mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. 15 Supplying and installation fo 32 mm dia G.I. pipe medium class IS 1239 marked in 3m length including all accessories and fittings required for installation of Submercible Pump sets. 16 Supply Installation testing & Commissioning of Radial / mixed flow ISI marked water filled submersible motor pump setssuitable for 100/150mm dia borewell.The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034:2018 and IS 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008,& IS12615:2011with required accessories including making connection suitable for Bore well. The job includes labour part of lowering ofriser pipe G.I./H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to switch board. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect . All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 17 3.0 HP, 1-Ø, (40 -170)Mtr, (60- 20) LPM 18 Supplying and Laying ISI marked P.V.C. insulated submersible cable as per PWD specification for electrical Worksconfirming to IS:694 and as per IS 8130 : 2013 of 1.1 kV grade .Wire should be made from99.99% purity copper, class 5 stranding in acc. to IEC 60228 forlower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4 including making connection etc. as required.OEM Must have its own in house NABL lab setup for all testing facilities for wires. All as per pre approved by Engineer in charge, making connections.For additional technical parameters of products/ work, referAnnexure A attached with this BSR . 19 4.0 Sq.mm 3 core flat / Round 20 Supply Installation testing & Commissioning ofISO certified company made DOL/Star-Delta Starter panel made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFFpush buttons,ammeter, voltmeter, indicating lamps etc.suitable for following rating motors complete in all respect. Appropriate type test certificate / OEM test report shall be submitted. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . For single phase Submersible / Monoblockpump0.5 HP to 3.0 HP (DOL starter)

BOQ

Name of Work: MP LAD 2023-24 CONSTRUCTION TOILET WORK AT GOVT. SENIOR SECONDARY SCHOOL RULYANA PATTI , BLOCK-NECHHWA DIST-SIKAR
Sl. No. Item Description
1Part-A : Civil WorkBased on BSR 2022, PWD Rajasthan
2Construction to tube well from ground levels and upto 100 meter depth and above to accommodate housing and assembly pipe of following sizes in all types of alluvium strata by percussion/ rotary drilling method and with gravel as per IS : 4097-1967 and packing as per IS : 2800 ( Part I & II ) 1979 as amended upto date ( the work includes the cost of gravel & its primary packing and packing during development. lowering of housing & strainer assembly pipes, with supply and wrappiing of coir rope, wherever necessary, for arresting fine sand particles. The work will not include cost of housing pipe and strainer pipe assembly and development work, but work would be completed after obtaining sand free water.)
3150 mm Nominal Bore.
4Construction ofTube well upto 100 meter depth and above in all type of rocks by DTH system and over burden, to accommodate casing pipe of following sizes in all types of soils and over burden including lowering of casing pipes, but excluding cost of casing pipes as per IS : after obtaining sand free water. The tube well should have a throughout bore as per nominal dia of casing pipe.
5150 mm Nominal Bore.
6Development of tube well as per ISI specification using suitable compressor to give free water for required yield of the gravel packed tube well.
7Supply fo ERW M.S. black casing pipe ISI marked ( IS : 4270/1992) of grade Fe410 of following sizes at site of work. Nominal bore of pipe (mm)
8150 mm nominal boae of pipe
9Supply of strainer pipes made of ERW M.S. black pipe ISI mark of following sizes at the site of work including required size fo slotting as pe IS: 8110 1985
10150 mm nominal boae of pipe
11Testing verticality of tube well by plumbing system and yield test and draw test by pumping system as per IS : 2800 (Part II) 1979.
12S & F tube well cover fo M.S. sheet (6mm thick) with nuts and bolts complete forsize.
13150 mm dia
14S & F M.S. Clamp, set of 50 X6 mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set.
15Supplying and installation fo 32 mm dia G.I. pipe medium class IS 1239 marked in 3m length including all accessories and fittings required for installation of Submercible Pump sets.
16Supply Installation testing & Commissioning of Radial / mixed flow ISI marked water filled submersible motor pump setssuitable for 100/150mm dia borewell.The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034:2018 and IS 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008,& IS12615:2011with required accessories including making connection suitable for Bore well. The job includes labour part of lowering ofriser pipe G.I./H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to switch board. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect . All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR .
173.0 HP, 1-Ø, (40 -170)Mtr, (60- 20) LPM
18Supplying and Laying ISI marked P.V.C. insulated submersible cable as per PWD specification for electrical Worksconfirming to IS:694 and as per IS 8130 : 2013 of 1.1 kV grade .Wire should be made from99.99% purity copper, class 5 stranding in acc. to IEC 60228 forlower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4 including making connection etc. as required.OEM Must have its own in house NABL lab setup for all testing facilities for wires. All as per pre approved by Engineer in charge, making connections.For additional technical parameters of products/ work, referAnnexure \"A\" attached with this BSR .
194.0 Sq.mm 3 core flat / Round
20Supply Installation testing & Commissioning ofISO certified company made DOL/Star-Delta Starter panel made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFFpush buttons,ammeter, voltmeter, indicating lamps etc.suitable for following rating motors complete in all respect. Appropriate type test certificate / OEM test report shall be submitted. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . For single phase Submersible / Monoblockpump0.5 HP to 3.0 HP (DOL starter)

AI Tender Summary

OUR REF NO 47395938
AUTHORITY Boards / Undertakings / PSU
TENDER VALUE 3.85 Lakhs
LAST DATE 30-01-2025
Authority
Authority Name RAJASTHAN COUNCIL OF SCHOOL EDUCATION
Work Description Tender For Construction Work At Govt. Senior Secondary School Rulyana Patti Block Nechhwa Dist. -Sikar - MP LAD 2023-24 CONSTRUCTION TOILET WORK AT GOVT. SENIOR SECONDARY SCHOOL RULYANA PATTI , BLOCK-NECHHWA DIST-SIKAR Sl. No. Item Description 1 Part-A : Civil WorkBased on BSR 2022, PWD Rajasthan 2 Construction to tube well from ground levels and upto 100 meter depth and above to accommodate housing and assembly pipe of following sizes in all types of alluvium strata by percussion/ rotary drilling method and with gravel as per IS : 4097-1967 and packing as per IS : 2800 ( Part I & II ) 1979 as amended upto date ( the work includes the cost of gravel & its primary packing and packing during development. lowering of housing & strainer assembly pipes, with supply and wrappiing of coir rope, wherever necessary, for arresting fine sand particles. The work will not include cost of housing pipe and strainer pipe assembly and development work, but work would be completed after obtaining sand free water.) 3 150 mm Nominal Bore. 4 Construction ofTube well upto 100 meter depth and above in all type of rocks by DTH system and over burden, to accommodate casing pipe of following sizes in all types of soils and over burden including lowering of casing pipes, but excluding cost of casing pipes as per IS : after obtaining sand free water. The tube well should have a throughout bore as per nominal dia of casing pipe. 5 150 mm Nominal Bore. 6 Development of tube well as per ISI specification using suitable compressor to give free water for required yield of the gravel packed tube well. 7 Supply fo ERW M.S. black casing pipe ISI marked ( IS : 4270/1992) of grade Fe410 of following sizes at site of work. Nominal bore of pipe (mm) 8 150 mm nominal boae of pipe 9 Supply of strainer pipes made of ERW M.S. black pipe ISI mark of following sizes at the site of work including required size fo slotting as pe IS: 8110 1985 10 150 mm nominal boae of pipe 11 Testing verticality of tube well by plumbing system and yield test and draw test by pumping system as per IS : 2800 (Part II) 1979. 12 S & F tube well cover fo M.S. sheet (6mm thick) with nuts and bolts complete forsize. 13 150 mm dia 14 S & F M.S. Clamp, set of 50 X6 mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. 15 Supplying and installation fo 32 mm dia G.I. pipe medium class IS 1239 marked in 3m length including all accessories and fittings required for installation of Submercible Pump sets. 16 Supply Installation testing & Commissioning of Radial / mixed flow ISI marked water filled submersible motor pump setssuitable for 100/150mm dia borewell.The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034:2018 and IS 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008,& IS12615:2011with required accessories including making connection suitable for Bore well. The job includes labour part of lowering ofriser pipe G.I./H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to switch board. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect . All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 17 3.0 HP, 1-Ø, (40 -170)Mtr, (60- 20) LPM 18 Supplying and Laying ISI marked P.V.C. insulated submersible cable as per PWD specification for electrical Worksconfirming to IS:694 and as per IS 8130 : 2013 of 1.1 kV grade .Wire should be made from99.99% purity copper, class 5 stranding in acc. to IEC 60228 forlower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4 including making connection etc. as required.OEM Must have its own in house NABL lab setup for all testing facilities for wires. All as per pre approved by Engineer in charge, making connections.For additional technical parameters of products/ work, referAnnexure A attached with this BSR . 19 4.0 Sq.mm 3 core flat / Round 20 Supply Installation testing & Commissioning ofISO certified company made DOL/Star-Delta Starter panel made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFFpush buttons,ammeter, voltmeter, indicating lamps etc.suitable for following rating motors complete in all respect. Appropriate type test certificate / OEM test report shall be submitted. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . For single phase Submersible / Monoblockpump0.5 HP to 3.0 HP (DOL starter)
Basic Detail
Tender No NIT NUMBER 02 (CIVIL) 2024-25 SMSA SIKAR
Bidding Type Tender
Location
City patti
State Rajasthan
Key Dates
Publish Date 25 Jan 2025
Submission Date 30 Jan 2025
Open Date 31 Jan 2025
Finance
Tender Value 3.85 Lakhs
Tender Fee 1000
EMD 7700
Exemption Not Available
Document List
f8d76a34-447d-48fd-8739-a140a49bc7ee.html
BOQ_798530.xls
Tendernotice_1.pdf
Tendernotice_2.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Jan 25, 2025
11:30 IST

Tender Published

Tender notice published.

Completed
Jan 30, 2025
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Completed
Jan 31, 2025

Bid Opening Date

Technical bids will be opened and evaluated.

Completed

Tender Documents

Download All (ZIP) ↓
html

f8d76a34-447d-48fd-8739-a140a49bc7ee.html

xls

BOQ_798530.xls

pdf

Tendernotice_1.pdf

pdf

Tendernotice_2.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender