|
| 1 | AUDITORIUM CHAIR WITH I FRAME, PP ARMREST, MANUAL TIP UPAND SEAT BACK COVER (including fittings & fixing) (Delivery, placing and installation of Auditorium Chairs. The chair seat should have s made up of 1.2±0.1cm Thk Plywood, upholstered with polyester fabric over moulded foam and covered with an injection-moulded polypropylene outer cover. The seat should have the provision to be manually tipped-up when not in use. *BACK SIZE: 46.3cm (W) X 59.0cm (H); SEAT SIZE: 47.0cm (W) X 49.5cm (D). The HR polyurethane foam should be moulded with density = 45 ±2 kg/m³ and Hardness load for Seat 16 ± 2 kgf and Hardness load for back 14 ± 2 kgf as per IS:7888 for 25% compression. The armrest should be made of Injection moulded PP compound.The Armrest needs to be mounted on a 3.15mm thick HR sheet which should be welded on the tubular frame. The understructure should be made of two straight I-leg of Ø3.81±0.03cm x 0.2 ±0.016cm THK M.S.E.R.W round tube and should be fixed with the seat support assembly using M8x15 INT. SOC HD M/C Screw QTY-2 NOS on each side. The seat support assembly should be made of a straight and bent tube of Ø2.22±0.03cm x 0.25 ±0.016cm THK M.S.E.R.W round tube with 5mm thk mounts at both ends.Manufacturer should have Green Guard (By UL), Green Pro, GRIHA, Indoor Advantage certification along with products certifications including AIOTA, INDIAN DESIGN MARK, BIFMA level 2 conforms to ANSI/BIFMA e3-2014e Furniture Sustainability Standard issued by BIFMA. Other certificates ISO 9001:2015, ISO 14001:2015, ISO 50001:2018, ISO 45001:2018 are mandatory. Manufacturer should have Green Guard (By UL) and BIFMA Certification for few of its products. All the ISO certificates should be obtained from NABCB (central Govt) accredited organization otherwise certificates will not be accepted. Supplier should have local service center with proper escalation matrix.Catalog of theProduct Should be provided for each product) |
| 2 | 3 SEATER SOFA (including fittings & fixing) (Delivery, placing and installation of 3 seater sofas.Size: Width 206 X Depth 90.5 X Height 85.5 X Seat Height 45 cm (±0.05cm acceptable) . The seat and foam should be made of PU foam in density 28±2 kg/cu.m with additional top layer of foam with in density28±2 kg/cu. Understructure should be 1.2±0.1 cm thick hot pressed plywood & pinewood. It shoudl be a welded assembly with SS 202 tube with plastic endcap.Manufacturer should have Green Guard (By UL), Green Pro, GRIHA, Indoor Advantage certification along with products certifications including AIOTA, INDIAN DESIGN MARK, BIFMA level 2 conforms to ANSI/BIFMA e3-2014e Furniture Sustainability Standard issued by BIFMA. Other certificates ISO 9001:2015, ISO 14001:2015, ISO 50001:2018, ISO 45001:2018 are mandatory. Manufacturer should have Green Guard (By UL) and BIFMA Certification for few of its products. All the ISO certificates should be obtained from NABCB (central Govt) accredited organization otherwise certificates will not be accepted. Supplier should have local service center with proper escalation matrix. Catalog of theProduct Should be provided for each product) |
| 3 | SOFA SET (3+1+1) (including fittings & fixing) (Delivery, placing & installation of 5 seater sofa. The sofa should have an orientation of 3+1+1 seats. 3 Seater Size: 175 x 83 x 86cm(±0.05cm acceptable),1 Seater Size: 92 x 83 x 86(±0.05cm acceptable), FRAME MATERIAL () should have TROPICAL WOOD / PINE WOOD/ RUBBER WOOD, with Moisture Content ( 10 – 12 %) : Less then 10% Anti – Tremite Treatment (Borex Powder Treatment) :Kiln Drying : N/A. Thickness of Plywood Standard of Plywood used: {Required Standard : IS 303 Commercial Plywood} used(mm) : 12mm & 18mm. SEAT FOAM should have (DENSITY, TYPE- Thickness (mm) : 69, 22 & 10 mm. Density (Kg/m3): 32dManufacturer should have Green Guard (By UL), Green Pro, GRIHA, Indoor Advantage certification along with products certifications including AIOTA, INDIAN DESIGN MARK, BIFMA level 2 conforms to ANSI/BIFMA e3-2014e Furniture Sustainability Standard issued by BIFMA. Other certificates ISO 9001:2015, ISO 14001:2015, ISO 50001:2018, ISO 45001:2018 are mandatory. Manufacturer should have Green Guard (By UL) and BIFMA Certification for few of its products. All the ISO certificates should be obtained from NABCB (central Govt) accredited organization otherwise certificates will not be accepted. Supplier should have local service center with proper escalation matrix. Catalog of theProduct Should be provided for each product) |
| 4 | Chair with Brake Castors for ABS Desklet only, Manual Tip up Seat (including fittings & fixing) (Delivery, placing & installation of stackable chairs. The seat sub-assembly should bemade up of 1.2±0.1cm thk Plywood upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The seat can tip-up when not in use and thshould befeature can be used while stacking the chairs horizontally The back sub-assembly should bemade up of injection-moulded polypropylene inner upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The contoured back with width extension at the bottom should be a should bedesigned to give comfort to lower back. The back flexing features allows the back to tilt by 9c±2\" to aid the user in adopting a comfortable reclining posture. Both these sub-assemblies should befixed to the tubular structure, BACK SIZE: 45.2cm (W) X 44.6cm (H), SEAT SIZE: 47.0cm (W) X 50.0cm (D). The powder-coated 4 leg structure should bemade of 2.2 ±0.03cm dia x 0.25 ±0.02cm thk M.S. E.R.W. Tube front and rear leg welded along with connecting tube made of 1.9 ±-0.02cm dia x 0.2 ±0.016cm thk M.S. E.R.W. Tube to form the tubular frame assembly. The legs should beprovided with injection-moulded adopter bush in black Nylon and brake-loaded castors enabling easy maneuvering while not in use and stable sitting while in use_ The chairs can be stacked horizontally when not in use. The Polyurethane foam should bemoulded with density = 70.0 ±8.0 kg/m3 and Hardness = 20 ±2 for Seat & 16 ±2 for back at 25% compression. Armrest structure should bemade up of 2.2 ±0.03crn dia x 0.25 ±0.02cm thk M.S. E R.W. Tube welded to the Tubular Frame structure and should have a scratch-resistantant ABS Arm top. The twin wheel castors should beinjection moulded in Black. It should have green certifications like GreenGuard, GreenPro, Indoor Advantage Gold, BIFMA Level 2, GRIHA V.2015: criterion 31, GRIHA V.2019: criterion 30 & SVAGRIHA criterion: 14) |
| 5 | Modular Tablewith Wire Mangaer(including fittings & fixing) (Delivery, placing & installation of modular table.Size: 135X 60 X 74 cmThe work top should be made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. The understructure should be made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990.The model panel shoudl be made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhanceaesthetics. It should be made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated. The wire management should consist of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables.It should have green certifications like GreenGuard, GreenPro, Indoor Advantage Gold, BIFMA Level 2, GRIHA V.2015: criterion 31, GRIHA V.2019: criterion 30 & SVAGRIHA criterion: 14.Manufacturer should have Green Guard (By UL), Green Pro, GRIHA, Indoor Advantage certification along with products certifications including AIOTA, INDIAN DESIGN MARK, BIFMA level 2 conforms to ANSI/BIFMA e3-2014e Furniture Sustainability Standard issued by BIFMA. Other certificates ISO 9001:2015, ISO 14001:2015, ISO 50001:2018, ISO 45001:2018 are mandatory. Manufacturer should have Green Guard (By UL) and BIFMA Certification for few of its products. All the ISO certificates should be obtained from NABCB (central Govt) accredited organization otherwise certificates will not be accepted. Supplier should have local service center with proper escalation matrix. Catalog of theProduct Should be provided for each product) |
| 6 | Chair with MS Understructure, Mesh back, With arms and Stackable(including fittings & fixing) (Delivery, placing & installation of multipurpose chair. The Seat should be injection moulded in glass filled Polypropylenecompound which is upholstered with fabric upholstery covers and moulded Polyurethane foam.The Back should be injection moulded in glass filled Polypropylene compound which should be upholstered withMesh fabric,SEAT SIZE : 50.0cm. (W) x 48.0 cm. (D), BACK SIZE : 53.0 cm. (W) x 39.0cm. (H). The HR polyurethane seat foam shoudl be moulded with density 45±2 kg/m³ and hardness 16±2 kgf as per IS:7888 for 25% compression. 3. M.S. POWDER COATED FRAMES FOR 4 LEG CHAIRS :The powder coated ( DFT50±10 microns) welded tubular main frame should be made from Ø 2.54 ± 0.03 cm x 0.2 ± 0.016 cm andØ1.6±0.3mm x 0.16 ± 0.0128cm M.S. E.R.W tube. The Ø1.9 ±0.3mm x 0.12 ±0.0096 cmM.S.E.R.W. tube used as connecting member between LH & RH frames. The powder coated( DFT 50±10 microns) welded tubular main frame should be made from Ø 2.54 ± 0.03 cm x 0.2 ± 0.016cm and Ø1.9 ±0.3mm x 0.12 ±0.0096 cm M.S.E.R.W. tube) |
| 7 | Alice Pro Coffee (including fittings & fixing) (Delivery, placing & installation of coffee table. The coffee table should have a tempered glass top. The external dimensions should be 1000 X 650 X 450 mm.Manufacturer should have Green Guard (By UL), Green Pro, GRIHA, Indoor Advantage certification along with products certifications including AIOTA, INDIAN DESIGN MARK, BIFMA level 2 conforms to ANSI/BIFMA e3-2014e Furniture Sustainability Standard issued by BIFMA. Other certificates ISO 9001:2015, ISO 14001:2015, ISO 50001:2018, ISO 45001:2018 are mandatory. Manufacturer should have Green Guard (By UL) and BIFMA Certification for few of its products. All the ISO certificates should be obtained from NABCB (central Govt) accredited organization otherwise certificates will not be accepted. Supplier should have local service center with proper escalation matrix. Catalog of theProduct Should be provided for each product) |
