|
| 1 | Sub Estimate No 1:- Pumping Machinery @RCC SupplyWell (Gut No 264)SubmersiblePumpset:- Providing, erecting and giving test of submersible pump set conforming to IS 8034 and motor conforming to IS 9283, with water proof winding. Pump shall be suitable for various delivery head and discharge with stainless steel shaft. Motor suitable for working on 415 V ± 10%, 3 Ph,50 Hz A.C. Supply, with cable guard, thrust carbon/fiber bearing to withstand entire hydraulic thrust. The pump set shall be suitable for direct coupling, with suitable suction strainer. Pump should have suitable discharge out let as per manufacturer\"s design. Antithrust stream lined non return valve shall be provided with the pump. 3 m submersible copper conductor cable in single / double run and 2 pairs of suitable size erection clamp 10 mm thick shall be provided with each pump.Head 50.0 Mtr & Discharge - 85000 LPH , 30.0 H. P.Submersible Pump 250 mm dia (with Bronze / Stainless steel(CF8M) Impeller) up to 8 stages |
| 2 | G I Pipe:- ProvidingLowering Laying & Jointing ISI mark G.I. pipe of following class and dia. excluding GST levied by GOI & GOM in all respect, inspection charges, transportation to stores, etc. complete150mm dia GI Pipe Medium Class |
| 3 | MS D F Pipes & Specials :- Providing and supplying ISI standard MS specials of required thickness with 3 coats of approved make epoxy paint (Shalimar, Ciba or Mahindra & Mahindra make) from inside and outside excluding all statutory duties & taxes such as GST levied by GOI & GOM in all respect, inspection charges, transportation to stores / site, and stacking, etc. complete. |
| 4 | MS Flanges :- Providing, fabricating, erecting,M.S. Flanges sleep on type (all tables) of required size and thickness with both side |
| 5 | Pressure Gauge :- Providing, erecting Pressuregauge of required range complete with syphon tube, isolating cock suitable for 12 mm dia G.I. Pipe. Pressure gauge shall be installed as directed,with tapping on rising main. 150mmdia |
| 6 | LT Panel :- Providing , erecting & Commissioning L.T. Control Panel comprising of all required electrical equipments as per detailedspecifications. |
| 7 | F.A.S.D.Starter :- Supplying and erecting Fully Automatic Star Delta starter to operate squirrel cage induction motor working on 380- 440 Volt, 3 phase, 50 Hz with no volt coil, over load element, and ON - OFF push buttons, with necessary material and connected to supply, etc complete. Starter with original sheet steel encloser. LG |
| 8 | Cables :-Supplying, erecting & terminating XLPE insulated 1100 V 3 Core 50 sqmm + 1 Core 35 Sqmm Aerial bunched aluminium cable along with necessary accessories for LT distribution on provided LT pole as per specification no. OHCBL/ ABC m3 Core x 50 sqmm + 1 Core 35 Sqmm Aerial bunched aluminium cable |
| 9 | Cables :- Supplying, erecting, testing and commissioning of flat flexible 3 core 16 sq.mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete. 3core x 16 sq.mm fromPanel to Motor |
| 10 | Earthing- Supplying, installing and testing earthing with galvanised iron earth plate size 60 x 60 x 0.6 cm complete with all accessories of GI materials & recording the results as per specification No. EA-EP |
| 11 | G. I. Earth Wire -Supplying and erecting GI earth conductor of required sizes used for earthing or any other purposes on wall with necessary GI clamps fixed on wall/cable/ conduit with screws complete. |
| 12 | Cable Jointing Kit : -Providing cable jointing kit withcablejointing compound and materials for various size cables from 1.5 mm. to 35 mm. cable soldering etc. complete. For requirement of cable of size 300 mm. and above single core cable shall preferably be used.complete. |
| 13 | Chain Pully Block : -Providing, erecting triple spurgear type Chain Pulley Block suitable for capacity as below with 6 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per IS 3832 carrying ISI mark. LF 2 Tonne Capacity |
| 14 | Shed For Pannel BoardExcavation for foundation / pipe trenches in hard murum and boulders, W.B.M. road including removing the excavated material upto a distance of 50 M beyond the area and lifts as below, stacking and spreading as directed by Engineer-in-charge, normal dewatering, preparing the bed for foundation and excluding backfilling, etc.complete.(Bd-A-3/259)Lift 0 to 1.5 m |
| 15 | Providing and laying in situ Cement Concrete M-15 of trap/ granite / quartzite / gneiss metal for foundation and bedding including bailing out water, form work, compaction, curing, etc. complete. PCC M-150 |
| 16 | Providing structural steel work in single stanchions composed of RSJ, channel, etc. with caps, bases, mild steel plates, angles, brackets, cleats, gusset plates, anchor bolts, etc. as per detailed design and drawing or as directed by Engineerin- charge including cutting,abrication, hoisting, erecting, fixing in position, making riveted / bolted /elded connections and one coat of anticorrosive paint and over it two coats of oil painting, etc. complete. |
| 17 | Providingandfixingplainzincsheetingof0.80mmthick(22B.W.G.)overtheridgehiporvalleytogalvanizedironsheetroofingincludingallfasteningandboltgalvanisedironscrews and bolts, lead and bitumen washers etc. complete.(Weight of 6.8 Kilogram/sq.m.). |
| 18 | ProvidingandfixingM.S.grilldoor 24Kilogram / OneSquareMetreofvarioussizeasperdetaileddrawingswithouthotdipcoating,ironfixturesandfasteningsand3coatsofoil painting etc |
