|
| 1 | Excavation in foundation in mixed soil with moorum,shingle,kankar required the special tools & plants including lift up to1.50 m. and lead upto 30m and including filling watering and ramming of excavated earth into the trenches and the side of foundation trenches or into the plinth and removal ,disposal of suurplus earth.si 251(a)Rates are including all labour, material, T&P, taxes & labour cess but excluding GST |
| 2 | Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete .As per ReferencetoMORT&H Specification 401SN. 4.01 Rates are including all labour, material, T&P, taxes & labour cess but excluding GST |
| 3 | Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with grader in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density..As per ReferencetoMORT&H Specification 406SN. 4.14 Rates are including all labour, material, T&P, taxes & labour cess but excluding GST |
| 4 | Providing and applying primer coat with SS1 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70to 1.00 kg/sqm using mechanical means.As per ReferencetoMORT&H Specification 502SN. 5.10Rates are including all labour, material, T&P, taxes & labour cess but excluding GST |
| 5 | Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of @ 0.30kg per sqm on the prepared bituminous surface cleaned with mechanical broom.As per ReferencetoMORT&H Specification 503 SN.5.02 Rates are including all labour, material, T&P, taxes & labour cess but excluding GST |
| 6 | Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binderVG-30 @ 4.5 per centby weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specificationcomplete in all respects.As per ReferencetoMORT&H Specification 505SN. 5.4 Rates are including all labour, material, T&P, taxes & labour cess but excluding GST |
| 7 | Providing and laying bituminous concrete withhigher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder VG-30 @ 5.4per centof mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification complete in all respectsAs per ReferencetoMORT&H Specification 507SN. 5.5Rates are including all labour, material, T&P, taxes & labour cess but excluding GST |
| 8 | Repeted Bar at main road by thermoplastic making of( on T junction/ Intersection ) 300 mm wide and 5mm height at 600 apart (one set is of 6 Strip).Rates are including all labour, material, T&P, taxes & labour cess but excluding GST |
| 9 | Constrution of Table Top(size 3.750 Mrt wide100 mm thick at center parabolic) on adjoining intersection of road with BCwith all material, T&P, material , labour complete as per direction of Engineer in charge. including all labour, material, T&P, taxes & labour cess but excluding GST |
| 10 | Supplying & Fixing ofReflective tree plate having Size 15 Cm x15Cm, Consisting type XI sheeting over 1.5mm thick aluminium sheet including labour. Material T&P etc for proper completion of the work.including all labour, material, T&P, taxes & labour cess but excluding GST |
| 11 | Providing and laying hot applied thermoplastic compound 2.5 mm thick i/c reflectrorising glass beads @ 250.00 gm per Sqm area thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC 35 including cost of all material , labour and T&P etc as per Table No.800-3 of clause MORTH |
| 12 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity grade sheeting Type IV vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-15 grade cment conc. 60 cm Circular with diffinitation plate (20 cm x 60 cm) 60 cm below ground lvel as per approved drawing (Speed Limit) Stop Sign high octagon |
| 13 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity grade sheeting Type IV vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-15 grade cment conc. 60 cm Circular with diffinitation plate (20 cm x 60 cm) 60 cm below ground lvel as per approved drawing (Speed Limit) Intersection,Pedestrian & Hump equilateral triangle |
| 14 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity grade sheeting Type IV vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-15 grade cment conc. 60 cm Circular with diffinitation plate (20 cm x 60 cm) 60 cm below ground lvel as per approved drawing (Speed Limit) Speed Limit Sign Circular |
| 15 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity grade sheeting Type IV vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-15 grade cment conc. 60 cm Circular with diffinitation plate (20 cm x 60 cm) 60 cm below ground lvel as per approved drawing (Speed Limit) Village Informatory rectangular |
| 16 | Reflective Raised Pavement Marker Providing and fixing of raised pavement markers (Cat Eye) Type x-ASTMD-4956-04 Avery Dennision/3m(USA Make) having moulded body of polycarbonate, ASA, HIPS or ABS able to support a load of 13.635 M.T. tested in accordance with ASTMD 4280 type H and other requirement mentioned in MoRT&H Circular, its reflective lens made of micro prismatic lens (capable of providing total internal reflection of light), electronically welded to the body. The length, height and width of the body shall not exceed 130 mm, 20 mm and 105 mm respectively, The area of each reflective surface shall not be less than 13 Sq. cm . on each side sloping at the angle of 35 + 5 degree to the base to ensure maximum reflectively. it shall comply to specification of Category A of MoRT&H circular no. RW/NH 33023/10/97-DO-III dated 11.06.97 lenses shall be moulded of methyl methecrylate conforming to ASTMD 788 or equivalent.With 7 years warranty. Rate shall be inclusive of all taxes, royalty, VAT etc. All T&P/ machine material and labour required for proper completion of work. including all labour, material, T&P, taxes & labour cess but excluding GST (as SI no.9 New item ) |
| 17 | Supplying & fixing of Linear Delineator System (LDS)panels made of Micro prismatic Retro Reflective sheeting Type XI duly laminated on thin aluminium foil to a unique corrugated shape to provide retro reflection across wide range of observations and external angles. Each LDS panel should be of nominal length of 33 inch and each ridge shall be approximately 0.34 inch high. Each LDS panel is to be firmly fixed onexistingConcrite / brick work with 16 NosFastner/ screwas per IRC 79-2019 -Rates are inclusive of all taxes, royalty,etc. all T&P/machine material and labour required for proper completion of work.Note : The Composite warranty jointly signed by original manufacturer & authorized converter of at least 7 years shall be furnished on non judicial stamp of required denomination.including all labour, material, T&P, taxes & labour cess but excluding GST (as SI no.12 New item ) |
