|
| 1 | (1) Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm. D.A.R No-15.23.1 |
| 2 | (1) Providing and laying vitrifed floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622 of approved make in all colours shades, laid on on 20 mm thick cement mortar 1:4 ( 1 cement 4 coarse sand) Jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigment etc. complete.Size of Tile 600x600 mm (D.A.R-11.41.2) |
| 3 | (1) Providing and fixing CI jali complete |
| 4 | (1) Cartage of surplus earth /malba loading and unloading but excluding stackings on pucca roads up to 15 km.(S.L231(a)-15 |
| 5 | (1) Supply and fixing ISI marked 32 mm thick flush door shutter commercial conforming quality conforming to IS : 2202 (Part I) including supply and fixing of hinges,screws, sliding bolt, tower bolt, door stoper and Allum. Handel etc complete work. |
| 6 | (2) Providing , Fixing ofAlmirah with mica laminated 18 mm HDHMRboard out side with one side decorative lamination .depth of cupordis 30 cm back side of cup board made by 5.5 mm thick HDHMRboard including cost of all acessires as handle hinges lock rolling chainel etc complete work |
| 7 | (2) Providing and Fixing of cup board with mica laminated 18mm HDMRboard out side with one side decorative lamination .depth of cupordis 30 cm back side of cup board made by 12mm thick HDMRboard including cost of all accessories such as handle, hinges, lock etc complete work.. |
| 8 | (2) Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mmapart including drilling 12 mm diameter holes andplugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1concentration DSR 2.53.1 |
| 9 | (2) Proding and fixing aluminium work for doors windows, ventilators and partitions with extruded built up standard tublar section/ appropriate Z section and other sections of approved make conferming to IS:733 and IS 1285 , fixing with dash fasteners of requried dia and size , including necessary filling up the gaps at at junction I.S at top bottom and sides with required EPDM rubber/ neoprene gasket etc alumimium section shall be smooth , rust free straight ,mitred and joints machanically where requried including clear angle , aluminum snap beading for glazing / paneling C.P Brass/ stainless steel screws all complete as per architectural drawing and the direction of Engineer-in - charge (glazing, paneling , and dash fasteners to be paid for separately)::for fixed portion:: powder coated aluminium ( minimum thickness of powder coating 50 micron (dsr -21.1.1.2) |
| 10 | (2) Proding and fixing aluminium work for doors windows, ventilators and partitions with extruded built up standard tublar section/ appropriate Z section and other sections of approved make conferming to IS:733 and IS 1285 , fixing with dash fasteners of requried dia and size , including necessary filling up the gaps at at junction I.S at top bottom and sides with required EPDM rubber/ neoprene gasket etc alumimium section shall be smooth , rust free straight ,mitred and joints machanically where requried including clear angle , aluminum snap beading for glazing / paneling C.P Brass/ stainless steel screws all complete as per architectural drawing and the direction of Engineer-in - charge (glazing, paneling , and dash fasteners to be paid for separately)::for shutters of doors, windows &ventilatorsincluding providing and fixing hinges/ pivots and making provision for fixings wherever required including the costof EPDM rubber/ neoprene gasket required(fitting shall be paid for seprately):: powder coated aluminium ( minimum thickness of powder coating 50 micron (dsr -21.1.2.2) |
| 11 | (2) Proding and fixing glazing in aluminium door , window ventilator shutter and partition etc with EPDM rubber / neoprane gasket etc complete as perarchitectural drawing and the direction of Engineer-in - charge (cost of aluminium snap beading shall be paid in basic item:(with float glass panes of 5 mm thickness (weight not less than 12.50kg/sqm)(dsr-21.3.2) |
| 12 | (2) Providing and fixing of glazing in Aluminium door/window, Ventilator shutter and Partitions etc, with EPDM Rubber/ neoprene gasket etc, complete as per the architectural drawings and the direction fo E/I (Cost of aluminium snap beading shall be paid in basic item with APC Sheet (Aluminium Power Coated Sheet). |
| 13 | (2) FILLING the gap in between allmunium frame and adjacent RCC/Brick/stone work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete complying to ASTM C920, DIN 18540-F & ISO 11600. Upto 10mm depth and 10mm width item no. dsr- 21.19.2 |
| 14 | (2) Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick &2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge. Anodized (AC 15 ) aluminium tubular handle bar dsr21.12.2 |
| 15 | (2) providing and fixing roller for sliding door complete |
| 16 | (2) P/F brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary citting and making good etc. complete.(D.S.R-21.13) |
| 17 | (2) Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. DSR-1.1.18 |
