|
| 1 | Supply and fixing cast iron Sluice valve PN 1.6 as per IS-14846, body, dome, wedge-CIIS:210, rings bronze IS:318, Spindle-SS IS-6603, Gland Packing gresy jute packing, fasteners-CS, Gasket-Natural rubber, Nominal size DN-150mm, both ends flanged in existing line without damaging to existing pipe line, fixed as in repair including dismentling taking down old unserviceable one complete all as specified and directed by Engineer-in-charge. Note :- Suitable size flanges for existing pipe line, joints and jointing material shall be included under this item. Make :- RMCO/Kirloskar/Venus |
| 2 | Description all as per item no 1 of above but size 100 mm dia Make :- RMCO/Kirloskar/Venus |
| 3 | Description all as per item no 1 of above but size 80 mm dia Make :- RMCO/Kirloskar/Venus |
| 4 | M&L for PCC 1:3:6 Type C2 for erection of fencing post/ mas concrete/supporting pillerwith 40 mm gradede coarse agreegete complete all as specified and as directed. |
| 5 | M&L for PCC 1:3:6 type C-1(20 mm graded aggregate) precast cement concrete block masonry with solid blocks exc 10 cm in width and setting in CM 1:6 etc complete all as specified and as directed. |
| 6 | M & L for 15mm thick rendering on fair faces of brick,stone work/concrete surfaces of wall in CM (1:4), finished surface even and smooth without using extra cement complete all as specified and as directed. |
| 7 | Excavation in trenches n. exc 1.5 mtr wide and n. exc 1.5 mtr depth for pole / cable / foundation etc incl getting out in soft /loose soil complete all as specified and directed. |
| 8 | Returning, filling in, approved earth including spreading, levelling, watering and well ramming in layers n.exc 25 Cm thick after cable are laid and tested complete all as specified and directed. |
| 9 | Removing excavated material / surplus soil to a distance not exc. 50 mtrs & deposited where directed at a level not exc.1.5 mtr above the ground level complete all as specified & directed. |
| 10 | M&L for High strength steel deformed TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel (annealed) wire not less than 0.90 mm dia. |
| 11 | M&L for Reinforced Cement Concrete M-25 (Design-Mix) using 20 mm garded stone aggregate as in foundation and supporting pillers for pipes complete |
| 12 | S&F Gun metal gate valves of 50 mm bore, (class I), ISI marked with iron wheel head, screwed both ends for iron pipe, ISI marked, including dismantling U/S gate valves complete all as specified and directed . Make :- Zoloto /Jindal/Sant |
| 13 | S&F Gun metal stop/gate valves of 40 mm bore, (class I), ISI marked with iron wheel head, screwed both ends for iron pipe, ISI marked, including dismantling U/S gate valves complete all as specified and directed . Make :- Zoloto /Jindal/Sant |
| 14 | S&F Gun metal stop/gate valves of 25 mm bore, (class I), ISI marked with iron wheel head, screwed both ends for iron pipe, ISI marked, including dismantling U/S gate valves complete all as specified and directed . Make :- Zoloto /Jindal/Sant |
| 15 | S&F Gun metal stop/gate valves of 20 mm bore, (class I), ISI marked with iron wheel head, screwed both ends for iron pipe, ISI marked, including dismantling U/S gate valves complete all as specified and directed . Make :- Zoloto /Jindal/Sant |
| 16 | S&F Gun metal stop/gate valves of 15 mm bore, (class I), ISI marked with iron wheel head, screwed both ends for iron pipe, ISI marked, including dismantling U/S gate valves complete all as specified and directed . Make :- Zoloto /Jindal/Sant |
| 17 | S & F in replacement of 150 mm bore air release valve double chamber as per IS 14845 including mounting GI pipe and clamps as per requirement at site suitable for cast iron pipe/ ductile iron pipe/GI pipe incl all fittings washer, nuts & bolt etc complete all as specified and directed.Make : KIrloskar/Zoloto/Sant/Leader |
| 18 | S & F in replacement of 100 mm bore air release valve doble chamber as per IS 14845 including mounting GI pipe and clamps as per requirement at site suitable for cast iron pipe/ ductile iron pipe/GI pipe incl all fittings washer, nuts & bolt etc complete all as specified and directed.Make : KIrloskar/Zoloto/Sant/Leader |
| 19 | S & F in replacement of 80 mm bore air release valve double chamber as per IS 14845 including mounting GI pipe and clamps as per requirement at site suitable for cast iron pipe/ ductile iron pipe/GI pipe incl all fittings washer, nuts & bolt etc complete all as specified and directed.Make : KIrloskar/Zoloto/Sant/Leader |
| 20 | S & F in replacement of 25 mm bore air release valve single chamber as per IS 14845 including mounting GI pipe and clamps as per requirement at site suitable for cast iron pipe/ ductile iron pipe/GI pipe incl all fittings washer, nuts & bolt etc complete all as specified and directed.Make : KIrloskar/Zoloto/Sant/Leader |
| 21 | M&L for structural MS frame work half round or other stock section including securing posts and stuts in fencing, frame work for pump house/gates of installations, base frame for equipments including securing bolts, posts and sturts in fencing including cutting and makeing shapes as desired, drilling holes, notching for wire cut to size and made to the exisitng shape suitable for fixing MS chequred duct covers / door panels, including nuts, bolts and washers, welding / bracing works, bendingcold or hot drilling holes for bolts in any shapeetc flat iron fillets (for securing wire mesh etc)all necessary drilling, bolting or riveting etc and similar work confirming to Fe-290 Gde E-165 including onecoat of primer and two coats of synthetic enamel paint to the entire steel surfaces all as specified and directed. |
| 22 | M&L for chain link MS galvanised fencing including lines wires, dia of chain link n less than 3.5 mm any mesh any size any type to any type strands rails, straining bolts etc. |
| 23 | S&F mild steel screw bolt (mechine made) with hexagonal or square, head, n.exc 5 cm but n.ecx 10 cm dia all as specified and as directed. |
| 24 | M&L MS angles as fencing port, struct cutting tops in shape incl all necessary drilling, notching and reveting etc and similar work confirming fe 310-0 pr fe 4120-0 all as specified and directed. |
| 25 | M&L TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and includingmild steel wire (annealed) not less than 0.9 mm dia or securing with clips all as directed. |
| 26 | Material and labour for preperation of new steel surface exceeding 10cm width or girth, including cleaning, washing and applying two coats of blue synthetic Enemel paint over on External sufaces of PS tank complete all as specified and directed. |
| 27 | Material and labour for preperation of new steel surface exceeding 10cm width or girth, including cleaning, washing and applying two coats of black bituminous paint anticorossive (suitable for drinking purpose) on internal sufaces of PS tank complete all as specified and directed. |
| 28 | Material and labour for writing letter or figures (Block, Roman, Italic or Indian) of size not exceeding 30 cm height with synthetic enamel paint all as specified and directed. |
| 29 | Supply and fix in replacement of cast iron foot Valve flanged end conforming to IS 4038 G.M body ring & Rubber flap lift type with CI stainer or MS stainerof size 100 mm (4”) dia all as specified & directed. |
| 30 | Supply and fix in replacement of cast iron foot Valve flanged end conforming to IS 4038 G.M body ring & Rubber flap lift type with CI stainer or MS stainerof size 150 mm (6”) dia all as specified & directed. |
| 31 | S & F inreplacementincl leakage testing galvanised steel water tubing medium grade 150 mm dia bore with all fittings such as bends, elbow, socket, reducer etc,connecting pipe to PVC tank through connectors as required at site, laid under floor / trenches all as specified & directed. |
| 32 | Description all as per item No 31 of above but of size 100 mm dia all as specified & directed |
| 33 | Description all as per item No 31 of above but of size 80 mm dia all as specified & directed |
| 34 | M&L in replacement of flanges of 8 holes suitable for 150/100/80 mm dia GI pipe including filling sealing compound all as specified & directed. |
| 35 | S&F leather sheet gasket 3 mm thick all as specified & directed by E-in-C. |
| 36 | S&F in replacement Bolts & nuts 24/20/15 mm dia or as per requirement at site all as specified & directed by E-in-C. |
