Supply of all matrials, Labour, T&P and execution of Constrution work at Birohi Village Pipe Water supply scheme Block Chhanve District - Mirzapur as complete in all respect including 100% household coverage by making FHTC (Functional househod tap connection ), commissioning, testing, trail run, defect liability and handing over to conerning Gram Panchayat. - Birohi WSS 2 Construction of 1.3 m high and 115mm thick boundary wall with 230 mmx230 mm thick pillar made in Brick masonry in 1 cement and 4 sand mortar, the spacing between two pillar should not be more than 3.0 m c/c and the depth of foundation should not be less than 0.60m, at the site of water works as per departmental type design and drawing, and, as per specifications given in the bid document including supply of all materials, labour T&P etc.for proper completion of work as per instructions of Engineer ‐in ‐ charge. (Drawing No.D‐1) 3 Supply and fixing of 3.6 m x 1.20 m MS gate including fabrication and supply of steel and construction of bounary wall pillars of size 1.35mx0.23mx0.23m with ornamental brick work 115mm th. around RCC, as per departmental type design and drawing (Drawing No. D‐1) and as per specifications laid down in the bid document, including supply of all material,labour,T&P etc.required for proper completion of work as per instructions of Engineer‐in‐charge. 4 Supplyandfixingof1.2mwideMSwicketgateincluding fabrication and supply of steel and construction of boundary wall pillars etc. as per specifications laid down in the bid document, including supply of all material, labour,T&P etc.required for proper completion of work as per instructions of Engineer‐in‐ charge. 5 Supply of all materials labour T&P etc. for complete construction of R.C.C. Over Head Tank of followingcapacityand staging above ground level with main components, including cost of soil testing and assuming bearingcapacity of soil as 8 MT, with supply of design and drawings.All the water retaining components of OHT shall be casted in M‐30 concrete and minimum grade of concrete of foundation and staging should be M‐25 with approved cement, coarse sand and stone grit as per I.S. 11682 and I.S.456Seismic effects and wind load should be taken into consideration as per I.S. 1893 for earthquake resistance and I.S. 875 part‐III for wind load on structure and including 1M wide RCC staircase, 1 m wide R.C.C. M30 balcony, M.S. ladder made of 50x50x6 mm angle section and 20mm plain M.S. bars with hand rails of 20mm medium class G.I. pipes, One aluminum ladder inside the tank from top dome to bottom dome, R.C.C. railing with 20mm dia medium class G.I.pipe (in 3 rows) on both sides of stair case, supported on 50x50x6mm M.S. angle section, spaced at intervals not more than 1.5m, Proper ventilator at top dome in circular shape of 1.2 m dia, Water level indicator fabricated with sensor connecting to automation, Lightening conductor as per I.S.S.2309 or its latest amendments of latest electricity rules, consisting of proper elevation rod with 5 or more fork points as prescribed in ISS 2309‐1969 and ISS 3013‐1966, C.I. manhole of min 60x60cm size with locking arrangement, Supply, fixing, jointing of D.I.D/F Pipes of appropriate size with D.I.D/F specials conforming to IS 8329/2000 as vertical pipes for inlet 6 250 KI 18 M Staging 7 Excavation of earth in ordinary soil (loam, clay or sand) for pipe line and rising main trenches including lift upto 1.50 m and lead upto 50 m and refilling watering, ramming of the excavated earth into the trench and also disposal of surplus earth upto 50m from the center of the trenches including supply of all material labour, T&P etc complete as per instructions of Engineer ‐in ‐charge. 8 Ordinary soil 9 Mixed soil with Kankar 10 Supply of following sizes (D.I.) pipes for rising main/distribution system conforming to latest/relevant I.S. 8329/2000 Specifications with all jointing materials such as specials conforming to latest /relevant I.S. specifications, suitable for D.I pipes, as per IS‐1239 /2000 and IS 8329/2000 or their latest amendment including F.O.R. destination and all taxes and insurance etc. with loading, unloading and Carting up to site of work, also including specials for these pipes and lowering them into the trenches and laying true to alignment and gradient and jointing etc. complete (including testing of pipe lines and cutting of pipes for making up the length but excluding the cost of trenches).all complete as per instructions of Engineer ‐in ‐ charge. 11 100 mm dia K‐9 12 Supply of following sizes pipes for ditribution system conforming to latest/relevant I.S 4984/1995 Specification with all jointing materials and specials conforming to leatest.Relevent I.S specifications including F.O.R. Destination and all taxes and insurance etc. with loading unloadingand carting up to site of work also including specials for these pipes and lowerring them into the trenches and laying true to alignment and gradient and jointing etc.complete ( including testing of pipe lines and cutting of pipes for making up the lenght but excluding the cost of trenches all complete as per instructions of Engineer -in-Charge. 13 63 mm dia HDPE Pipe PN‐6: Class PE‐100 14 Supply and carting up to site of work of the following dia DI butterfly/sluicevalves,classI,workingpressure10Kg/cm2 confirming to IS: 780/1969 or its latest amendments,including valve fittings & Dismantling Joints as per requirement F.O.R. destination, and lowering them into the already prepared trenches, fixing in position and jointing them with pipelines and testing etc. complete and also including supply of jointing materials etc. complete .including all taxes and insurance, as per instructions of Engineer ‐in ‐charge. 15 Sluice valve ‐125 mm dia 16 Sluice valve ‐100 mm dia 17 Sluice valve ‐80 mm dia 18 Construction of following type chambers as per department type design and drawing including Heavy duty M.S. Manhole Cover and all materials, labour, T&P etc complete forproper completion of work as per instructions of Engineer ‐in ‐charge. 19 Sluice valve chamber ( masonry type )dia upto 200 mm ‐ 1000 (L) x 1200 (W) x 1300 (H) mm 20 Water recharge Mechanism within the water works campus 21 Dismantling of the followingtype of road surfaces including supply of all materials labour T&P etc. required for proper completion of the work as per instructions of Engineer-in-charge 22 B.O.E. surface 23 Bituminous surface 24 Interlocking Road 25 C.C. Road 26 Reinstatement of the followingtype of road surfaces with old and new materials including supply of all materials labour T&P etc. required for proper completion of the work as per instructions of Engineer-in-charge 27 B.O.E. surface( 50% of existing bricks to be reused) 28 Bituminous surface 29 Interlocking Road 30 C.C. Road 31 Provision for following types of Culvert crossing along the alignment of pipe line complete as per instructions of Engineer ‐in ‐charge. ( casing of pipe is done by concreting) 32 Nala/Culvert Crossing ( width ‐3.5 m) upto Dia 300 mm 33 Making house connection should be done atleast 2 m inside the boundary wall with provision of tap from distribution line to outer wall of house, with supply of 1 m G.I. pipe ( 15 mm ) ( above ground )& average 10 mtr. MDPE Pipe ( 20 mm)( below ground) including specials,saddle, Tap,etc. of suitable size, T&P etc. including excavation, laying and jointing for proper completion of work as per instructions of Engineeras per Dwg 12 ( excluding road restoration) 34 Construction of single tap pillar type stand post as per type design 35 Interconnection of newly laid rising main pipe line to OHT and making bypass arrengement and connection with pump no.2 including all specials materials labour T&P etc all complete. 36 Painting of pump house, staff quarter and boundry wall including scraping of old paint and painting with one coat white cement based priming coat and two coat weather proof exterior emulsion ofnasian/berger/nerolacincluding supply of all material labout,T&P etc. complete. 37 Sluice valve - 50 mm dia 38 Display Board ( 2m X 1m )
