|
| 1 | Dismantling all type of plain cementconcrete works, stacking serviceable materrials at site and removing rubbish as directed with in a lead of 75 m In ground floor including roof. |
| 2 | (b) above 150 mm. thick. |
| 3 | Earth work in excavation of foundation trenches or drains in all sorts of soil (including mixed soil but excluding laterite or sand stone) including removing, spreading or stacking the spoils within a lead of 75m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. . |
| 4 | (a) Depth of excavation not exceeding 1.500 mm. |
| 5 | Laying 150 mm. to 200 mm. boulder soling including rough dressing hand packing and ramming down small pieces in the interstics without rolling but including ramming. |
| 6 | Cost of stone boulder 150 mm size delivered ans stacked at site. |
| 7 | (II) Cement concrete with 30 mm. down graded shingles excluding shuttering.N.B. VarietyIn ground floor . |
| 8 | (a) 1:3:6 proportion. |
| 9 | Hire and labour charge for shuttering with centreing and necessary staging up to 4 m. using approved stout props and thick hard wood planks of approved thick ness with required bracing for concrete slabs, beams, columns, lintels curved or staight including fitting fixing and striking out after complection of works. (up to roof of ground floor). |
| 10 | (f) 25mm. To 30mm. Shuttering with out staging in foundation etc. |
| 11 | Plaster ( to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (ground floor). [Excluding cost of chipping over concrete surface]. |
| 12 | (ii) With 1:4 cement mortar . |
| 13 | (c)10 mm. thick plaster. |
| 14 | Neat cement punning about 1.5mm thick in wall, dado, windowsill, floor etc.NOTE:Cement 0.152 cu.m per100 sq.m. |
| 15 | Tack Coat Providing and applying tack coat with Cationic Bitumen Emulsion of approved grade conforming to IS:8887-1978 on the prepared surface cleaned with Hydraulic broom, moistening the surface including cost and carriage of emulsion, hire charges of machinery and labour, cost of fuel and lubricants all complete asper Clause 503 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). |
| 16 | On Bituminous Surface (Using Bitumen Emulsion at the rate of 0.20 to0.30 kg per sqm.) |
| 17 | Bituminous Macadam using Hot Mix Plant (HMP) Providing and laying bituminous macadam with Hot Mix Plant using approved crushed aggregates of specified grading as per Table 500.7 premixed with bituminous binder, transported to site laid over apreviously prepared surface at specified laying temperature with paver finisher to the required grade,level and alignment and rolled with suitable power roller for break down, inter-mediate and finished rolling as per specification to achieve the desired -compaction including cost and carriage of stone materials and bitumen, hire charges of machinery and equipment, cost of fuel and lubricants and wages of operational staff, quality control complete as per Clause 504 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). |
| 18 | For Grading II(19 mm nominal size, 50-75 mm thick.) |
| 19 | Using Batch type HMP of minimum capacity 60-90 TPH |
| 20 | Mastic Asphalt Providing and laying Mastic asphalt wearing course with paving grade bitumen meeting the requirements given in table 500-29 using approved coarse aggregate,fine aggregate, filler material and bitumen, prepared by using Mastic cooker including cost and carriage ofall ingredients, cost of heating aggregates and binder,mixing in specified proportions conforming to approved Job Mix Formula and laid to required level and slopeafter cleaning the surface, compacting, sealing the construction joints and surface finishing conforming to specifications including providing antiskid surface with bitumen pre-coated fine-grained hard stone chipping of13.2 mm nominal size at the rate of 0.005 cum per 10sqm and at an approximate spacing of 10 cm center tocenter in both directions, pressed into surface when the temperature of surfaces not less than 100°C, protruding1 mm to 4 mm over mastic surface, including the hire charges of all tools and plants and machinery, pay of operators, cost of |
| 21 | 25 mm thickness |
| 22 | GST18% |
| 23 | 1% L W CESS |
