|
| 1 | Supplying, Installation, testing and commissioning of HOT Dip galvanized octagonal steel pole of7 mtr height and made of 3 mm thick sheet,having bottom 135 mm OAF & top 70 mm OAFprovided with welded base plate of size 225 mm x 225 mm x 16 mm thick with built in connector control box complete with 250mm wide 3 mm thick hot dip galvanised MS strip in octagonal shape welded permanenty around on window cover/juction box i/c providing L hook in opposite side of control box just below the M.S. strip provided on juction box/cover box of suitable projection from the pole shaft to prevent the movable juction/cover box going down to the base plate and making a suitable site of hole on above the L-Hook (600mm approx) to hold the juection/cover box during the maintenance i/c covering with M.S. cover arrangement the hole to prevent entry of rain water through it completeas per drawing & technical specifications attached and providing followingaccessories with mounted inbuilt control box having flush cover with 2 nos. mounting strips with tapped holes on existing RCC foundation with bolt and nuts, making connections, interconnections with suitable size of copper wire with thimble/lugs in the connector box, earthing, marking/ numbering of pole etc. complete as per drawing & technical specifications attached including following accessories with mounted inbuilt control box.(a). 6mm thick phenolic laminated/Bakelite sheet inside the window mounted on the existing mounting strips inside the flush door.(b). 1 no. 63 Amp terminal block suitable forfollowing conductor / cable, fixedonDIN channels i/c providing and fixing DIN channel of suitable length – on the existing phenolic laminated / Bakelite sheet.(i) 16 sq mm conductor – 2 nos. (incoming and outgoing looping) (ii) Terminal suitable for 6 SWG GI wire / 2.5 sq mm wire.(c).6 Amp,SP MCB,10 KA, ‘C’ Series – 1 no. including mountings on DIN channel, Earth stud 2 Nos. welded at suitable height i/c washers, springs washers & nuts etc.(d) Suitable arrangement for saddling of incoming / outgoing cables. |
| 2 | Providing and laying in position, M25 reinforced cement concrete foundation of size 450 mm (L) x 450 mm (W) and 1400 mm (D) i/c excavation of earth, providing cutting, bending and placing in position reinforcement of cold twisted bar of 12 mm dia. 1600 mm long (approx.) – atleast 8 Nos. and reinforcement ring of cold twisted bar of 10 mm dia. 1800 mm long (approx.)- atleast 10 Nos. (with 140 mm spacing) i/c supplying of 4 Nos. M-24 x 700 mm long (150 mm top threaded & 250 mm top galvanized portion) M.S foundation bolt (EN 8-grade) with 4 Nos. nuts and 4 Nos. washer, bolt along with 2 Nos. templates/Anchor plate of size 225 mm x 225 mm x 4 mm thick having 4 Nos. 24 mm dia. holes to match with PCD of poles base plate with positioning of foundation bolts and providing 63 mm (OD) 2 Nos. DWC pipe for cable entry/exit, plastering & painting the foundation above the ground level etc complete as required. |
| 3 | Supplying & fixing of hot dipGalvanized minimum 500 mm long Bracket (to be installed at 7 mtr height) made out of suitable sized round pipe B-Class on octagonal pipe (3.60 mm Thick), 48 mm outer dia with 300 mm longgalvanized overhang with tightening bolts etc. as reqd. Tilt angle shall be around 10degree.a) Single arm bracket |
| 4 | Supplying of following size of XLPE insulatedaluminium Conductor having stranded wire armourd power cable of 1.1 KV grade i/c making, connection testing etc. as reqd.a) 2C x 16 sq.mm |
| 5 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.a) Upto 35 sq. mm |
| 6 | Supplying and laying of following sizeDWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc.conforming toIS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. i) 90 mm dia (OD- 90mm & ID-76 mm nominal) |
| 7 | Providing boring and laying of HDPE pipes (ISI marked) confirming to IS:4984 with pressure rating of 6kg/Sq.cm by trench less technology with no dig. method by making bore hole in horizontal direction across the road with boring equipment a) 90 mm (outer dia) |
| 8 | Earthing with G.I earth pipe 4.5 mtr. long X 40 mm dia i/c accessories and providing masonry enclosure with cover plate, having locking arrangement and watering pipe etc. with charcoal or coke & Salt as reqd. |
| 9 | Providing & Fixing25 mm X 5 mm G.I Strip on surface on in recess for connection etc. as reqd. |
| 10 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. |
