|
| 1 | Surface Dressing of the ground in any kind of soil including removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto 75 m as directed. |
| 2 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.(a) Depth of excavation not exceeding 1,500 mm. |
| 3 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work)a) With earth obtained from excavation of foundation. |
| 4 | Filling in foundation or plinth by Fine sand in layers not exceeding 150 mm. as directed and consolidating same by thorough saturation with water ramming complete, including the cost of supply of sand. (Payment to be made on measurement of finished quantity) |
| 5 | (I) Cement concrete with graded stone ballast (40 mm size excluding shuttering)In ground floor(A) [Pakur Variety](a) 1:3:6 proportion |
| 6 | Controlled Cement concrete with well graded stone chips (20 mm nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test and job mix foumula. In ground floor and foundation.[using concrete mixture] |
| 7 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 8 | Ordinary Cement Concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement, If any, in ground floor. as per relevant IS codes.(a) Pakur Variety. In ground floor |
| 9 | Ordinary Cement concrete (mix 1:1.5:3)with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.a) Pakur Variety |
| 10 | Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. |
| 11 | Hire and labour charges for shuttering with centreing and necessary staging upto 4 m. using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works. (upto roof of ground floor)(c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work.Ground floor |
| 12 | (f) 25mm. to 30mm. shuttering without staging in foundation |
| 13 | Reinforcement for reinforced concrete work inall sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. (i) Tor steel/Mild Steel. II. JSW/JSPL/SHAYAM/SRMB/BMASL/ELECTROSTEEL/SSL(IN GF)1.%*7.85*Concrete Volumn |
| 14 | Brick work with 1st class bricks in cement mortar (1:6)(a) In foundation and plinth |
| 15 | (b) In superstructure, ground floor |
| 16 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) inground floor. |
| 17 | Extra for using approved H.B netting in every third layer in 125 mm. thick brick work in any floor |
| 18 | 40 mm. thick damp proof course with cement concrete (1:1.5:3) (with graded stone chips 20 mm nominal size) with water proofing compound of approved brand @ 0.2% weight of cement including cost of materials over two coats of non toxic acrylic polymer modified cementitious waterproofing slurry coat complete [cost of water proofing compound and non toxic paint to be paid seperately) for underground water retaining structures. |
| 19 | (a) Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer\"s specification. |
| 20 | Supplying and laying true to line and level Anti-Skid, Full Body, Homogeneous& Granular finish Vitrified Tiles conforming to IS:15622-2006 & IS 4457-2007and testing shall be made in accordance with IS:13630 [Non- modular sizes fortiles with Skid resistance > 0.5, Mohr\"s hardness > 5.0, Staining resistance:Class-1, Water Absorption: E < 0.5%], MOR > 35 N/sq.mm in Internal area ofbuilding e.g. Toilet Block, Passage, Corridor, Accessible Open Terrace etc. setin 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry at back side oftiles using cement @ 2.91 Kg./Sqm or using Polymerised Adhesive (6 mm thicklayer applied directly over finished artificial stone floor/ Mosaic etc without anybacking course) laid after application slurry using 1.75 Kg of cement per Sqmbelow mortar only, joints grouted with admixture of white cement and colouringpigment to match with colour of tiles/ epoxy grout materials of approved make asdirected and removal of wax coating of top surface of tiles with warm water andpolishing the tiles using soft and dry cloth upto mirror finish complete includingthe cost of materials, labour and all other incidental charges complete true to themanufacturer\"s specification and direction of Engineer-in-Charge. (Whitecement, synthetic adhesive and grout material to be supplied by the contractor).b) In Ground Floor: Sizes-600 mm x600mm x10 mm with breaking strength >1500 N |
| 21 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(B) WallWith Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.(b) Area of each tile above 0.09 Sq.m. (i) Coloured decorativeGround floor |
| 22 | Supplying,fitting & fixing granite slab 15mm to 18mm thick infloor, lobby, stair, landing and treads etc. over 20mm (avg)thick base of cement morter (1:2) laid with white cement slurry@ 4.40Kg per Square meter before placing of granite andjointed with white cement slurry @ 2.0 Kg per square meterwith necessary pigments and complete as per direction ofEngineer-in-charge including cost of all materials, labours,curing and roughening of concrete surface complete.In ground floor(iii) Area of each Slab/tile exceeding 0.60 sq.m but not exceeding 1.00 sq.m. |
| 23 | Extra cost of labour for prefinished and premoulded Nosing to treads of steps, railing, window sill etc. of Marble Stone. |
| 24 | Extra cost of labour for Marble Stone Floor in treads of Steps. |
| 25 | Supplying, fitting & fixing Glass mosaic tiles at finished plain wall surface of size 20 mm x 20 mm x 4 mm in all color, design, fixing in customize design as per direction of engineering- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge. [At Ground Floor] iii) Mural aligned/ CAD Design Type |
| 26 | Supplying& laying 20 mm designer chequered tiles of any shade and of approved quality as per IS: 1237: 1980 laid in patterns as directed in pavement, footpath including necessary underlay 25 mm thick average cement mortar (1:3) complete in all respect with all labour and materials [using cement slurry @ 4.4 kg/Sq.m at back side of tiles. Cement of mortar & slurry will be supplied by the Department. Border concrete if necessary to be paid separately]. |
| 27 | Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x 10mm x 2mm vertical channels 100mm apart in fully stretched position 20mm x 5mm M.S. flats as collapsible bracings properly rivetted and washered including 38mm steel rollers including locking arrangements, fitted and fixed in position with lugs set in cement concrete and including cutting necessary holes, chasing etc. in walls, floors etc. and making good damages complete.In ground floor. |
| 28 | (a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.(i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr.In ground floor. |
| 29 | Supplying, fitting and fixing Stainless Steel railing consist of 38mm dia and 900mm height vertical balustrade at every two alternative steps, 50mm dia top rail, 3 (three) nos 19mm dia horizontal Strainless steel pipe and base/cover plate with Strainless Steel GRADE 304 containing 7.5% nickle (Interior Grade) Brushed/Mat finish, complete as per direction of the Engineer-in- harge. Weight of Strainless Steel railing per metre 6.5 Kg (approx)In ground floor. |
| 30 | Labour for Chipping of concrete surface before taking upPlastering work. |
| 31 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints or rougening of concrete surface, including throating, nosing and drip course where necessaryi) With 4:1 cement mortar ( Due to saline area and fluted ,corrugated or ribbed plaster).(i) With 6:1 cement mortar(b) 20 mm. thick plaster (a) In ground floor. |
| 32 | (b) 15 mm. thick plaster(ii) With 1:4 cement morta(i) In ground floor. |
| 33 | (c) 10 mm. thick plaster(i) In ground floor |
| 34 | Extra for fluted, corrugated or ribbed plaster (over rate of corresponding rate of plaster). (Cement 0.135 Cu.m/100Sq.m) |
| 35 | Neat cement punning about 1.5mm thick in wall, dado, windowsill, floor etc.NOTE: Cement 0.152 cu.m per100 sq.m |
| 36 | Supplying,fitting & fixing of 2-Track / 3-Track Aluminium sliding Window of all Aluminium sections viz. window frame (top,bottom & side frame), shutter (top, bottom, side & interlock member) made of aluminium alloy extrusions conforming to IS 733-1983 & IS 1285-1975, annodised conforming to IS 1868-1983, fitted with all other accessories viz. PVC roller, EPDM gasket, maruti lock, screws etc. including labour charges for fitting & fixing of aluminium 2- rack/3-track sliding window with fixing of glass (excluding cost of glass) all complete as per architectural drawings and direction of Engineer-in-charge.(A) In 10-12 Micron thickness Annodizing filmFor 2-Track window : Members for Bottom frame @ 0.875 Kg per Mtr. and for Top and Side frame @ 0.778 Kg per Mtr. and for shutter Bottom and Top member @ 0.472 Kg per Mtr., Style side member @ 0.493 Kg per Mtr. and Interlock member @ 0.612 Kg per Mtr. |
| 37 | Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987. ii) 4mm thick coloured / tinted / smoke glass. |
| 38 | Supplying profiles of required section made of Aluminum Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Anodized (with required film thickness andspecified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composite door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - In Charge. (Payment will be made on finished length of the work).(A) In 10-12 Micron thickness Anodizing filmI) Natural whiteh) Louvered window.i) Top, bottom and side member |
| 39 | ii) Louvered Section. |
| 40 | iii) Cleat angle ( Non-anodized). |
| 41 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps.(e)Sal: Malayasian(i) In Gr. Floor |
| 42 | Supplying, fitting and fixing fibre reinforced polymer (FRP) Composite door frame as per approved section with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to safisfy IS: 4020 door testing performance criteria.(i) 66mm x 90mm |
| 43 | Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings.In ground floor(iii) 35mm thick shutters with 19mm thick panel of size 30 to 45 cm(b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. |
| 44 | Supplying, fitting & fixing fibre reinforced polymer (FRP) Composite door shutters as per approved design with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to satisfy IS:4020 door testing performance criteria.In ground floor.(i) 32 mm thick |
| 45 | Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately)(a) 40mm X 6mm, 250mm Length |
| 46 | Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws:(iv) 150mm long x 10mm dia. bolt. |
| 47 | (x) 300mm long x 12mm dia. Bolt |
| 48 | Anodised aluminium butt hinges of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 205/66) and fitted and fixed with cadmium plated screws:(v) 100 x 63 x 3.2mm |
| 49 | Anodised aluminium decorative handle (hexagonal / fluted) of approed quality fitted and fixed complete.:(ii) 175mm plate x 12mm dia rod x 60mm hexagonal / fluted. |
| 50 | Anodised aluminium Aldrop / Sliding bolts of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 2681/66) fitted andfixed complete.(i) 250mm x 16mm dia bolt |
| 51 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC.(i) 250mm x 16mm dia bolta) Two Coat.i) Water based interior grade Acrylic Primer |
| 52 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC.(b) Two Coats(i) In Ground Floor: |
| 53 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer\"s specification and as per direction of Engineer-in- harge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.c) Super Protective 100% Acrylic Emulsion.(i) In Ground Floor:(Two Coat) |
| 54 | Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) :(Two coats)i) Standard Quality(i) In Ground Floor:(Two Coat) |
| 55 | Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick)(i) In Ground Floor. |
| 56 | (a) Priming one coaton steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 57 | (b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc |
| 58 | (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary: (b) On steel or other metal surface :With super gloss (hi-gloss) -(i) Two coats (withany shade except White) |
| 59 | (a) On timber or plastered surface :With super gloss (hi-gloss) -(i) Two coats (withany shade except White) |
| 60 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete.A) UPVC Pipes:(iii)160 mm. Dia. |
| 61 | B) UPVC Fittings:c) Bend 87.5 degree(iii)160 mm. Dia. |
| 62 | d) Shoe(iii) 160 mm. Dia. |
| 63 | Supplying, fitting and fixing cast iron heavy type spiral staircase of approved design with 50 mm.dia. Stem and C.I. Steps 150 mm as per design 900 mm. high C.I, railing including necessary M.S. tie of suitable section embedded to wall with cement concrete (1:2:4) including cost of intermediate C.I. platform secured with necessary tie to stem and wall with cement concrete (1:2:4) including fixing the stem in ground with cement concrete (1:3:6) complete in all respect with all labour and materials(b) With 900 mm.dia. Well |
| 64 | S & PSupplying, fitting and fixing shower of approved brand and make.(b) Chromium plated Rose shower with revolving joint and 150 mm long shower arm (Equivalent to Code No. 5489 & Model - Florentine of Jaquar or similar brand). |
| 65 | (f) Hand Shower(Health Faucet) with 1mtr Fexible Tube with Wall Hook(Equivalent to Code No.573 & Model -ALLIED of Jaquar or similar). |
| 66 | Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only).(v) 40 mm dia |
| 67 | (vi) 32 mm dia |
| 68 | (vii) 25 mm dia |
| 69 | Supplying, fitting and fixing bib cock or stop cock.a) (i) Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand). |
| 70 | (b) (ii)Chromium plated Concealed Stop Cock (Equivalent to Code No. 514(A) & Model - Tropical / Sumthing Special of ESSCO or similar). |
| 71 | (d) (i) Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar). |
| 72 | f) (ii) CP 2-way bib Cock - 15 mm, supplied, fitted and fixed. (Code No.5041 & Model - FLORENTINE of JAQUAR or similar brand |
| 73 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbow, nipple, long screw, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required, jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accessories, specials. Payment for painting will be made separately)(a) For Exposed Work -- PVC Pipes (Dia)50mm |
| 74 | 40 mm |
| 75 | 32 mm |
| 76 | 25 mm |
| 77 | (b) For Concealed Work15 mm |
| 78 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. |
| 79 | Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer.(d) 2000 litre capacity |
| 80 | Labour for hoisting plastic water storage tank.(ii) Above 1500 litre upto 5000 litre capacity(a) Upto 1st story from G.L. |
| 81 | Labour for punching hole in plastic water storage tank upto 50 mm dia. |
| 82 | Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint.(i) 630 mm X 450 mm size |
| 83 | Supplying, fitting and fixing pedestal of approved make for wash basin (white) |
| 84 | Supplying, fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia.(i)450 mm long |
| 85 | (iii)600 mm long |
| 86 | Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps.(iii) 900 mm long |
| 87 | Supplying, fitting and fixing Waste fittings complete.(a) C.P. over brassii) 32 mm |
| 88 | Supplying, fitting & fixing Aluminium domical grating.(iii) 100 mm |
| 89 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992(A) (i)Single Socketed 3 Meter Length (b) 110 mm |
| 90 | (A) (iii) Single Socketed 1.8 Meter Length (b) 110 mm |
| 91 | (vii) Double Socketed 0.60 Meter Length(b) 110 mm |
| 92 | (B) Fittings(iii) Door Tee(b) 110 mm |
| 93 | vi) Door Y (LH) & (RH)(b) 110 mm |
| 94 | xi) Door Bend (T.S.)(b) 110 mm |
| 95 | xv) Vent Cow(b) 110 mm |
| 96 | xxi) 110 X 110 P Trap75 mm |
| 97 | xvii) W.C. Connector (150 mm long) 125 X 110(W/WC Ring)75 mm |
| 98 | Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materialsetc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any floor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Engineer-in-charge. (Payment will be made on centre line measurement of the total pipeline including specials. (A)Above ground(ii) 110 mm dia. |
| 99 | Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc.(a) With \"P\" trap |
| 100 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding \"P\" or \"S\" trap (excluding cost of concrete for fixing).i)(i) 580 mm X 440 mm |
| 101 | Supplying, fitting and fixing Flat back urinal (half stall urinal) in whitevitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete.(i) 635 mm X 395 mm X 420 mm |
| 102 | Supplying, fitting and fixing Squatting plate with integral flushing in white vitreous chinaware of approved make in cement concrete (6:3:1) with jhama chips complete. (Payment of concrete will be paid separately).(i) 450 mm X 350 mm |
| 103 | Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete..(a) E.W.C.(iv) Bestolite (solid type) white |
| 104 | Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete.i) Polythene Flush Pipe |
| 105 | Supplying, fitting and fixing urinal flush pipe fittings of approved brand.(a) C.P. urinal flush pipe fittings range of one |
| 106 | Supplying, fitting and fixing 18 mm thick marble partition slab with chawk doongri marbel square cut, both sides polished with two front corners rounded and edges polished. |
| 107 | Supplying, fitting and fixing liquid soap container.(b) PTMT(Prayag or equivalent) |
| 108 | Supplying, fitting and fixing soap holder.(a) PTMT (Prayag or equivalent) |
| 109 | Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm |
| 110 | Supplying, fitting and fixing towel rail with two brackets.(b) Aluminium(ii) 25 mm dia. and 600 mm long |
| 111 | Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chipsover a layer of jhama brick flat soling,15 mm thick (1:4) cement plaster to inside walls and out-side walls upto G.L. and 20 mm.thick (1:4) plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (1:4) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials.i) With Pakur variety JSW/JSPL/SHYAM… |
| 112 | Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C(1:1.5:3) bottom slab including supplying, fitting and fixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and fefilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials.(iv) For 50 usersA) With Pakur variety.JSW/JSPL/SHYAM |
| 113 | Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) toinside face upto the depth of cement brick work, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slabincluding filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials.With 250 mm thick dry brick work and 250 mm thick cement brick work (6:1) and 1.00m inside dia. ( .JSW/JSPL/SHYAM….) |
| 114 | E.I Work Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded \"FR\"PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polythen pipe complete with all accessories embedded in wall tolight/fan/call bell points with Modular type switch (Brand approved by EIC) fixed on Modular GI switch board with top cover plate flushed in wall incl. mending good damages to original finish. 8mtr |
| 115 | Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded \"FR\" PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polythen pipe complete with all accessories embedded in wall to 240 V 6A 5 pin plug point incl. S&F 240 V 6A 3 pin Modular type plug socket & Modular type switch (Brand approved by EIC)incl. S&F earth continuity wire, fixed on 4 Module GI switch board with 3/4 Module top cover plate flushed in wall incl.mending good damages to original finishOn Board |
| 116 | Supplying & Fixing 6 way GI Modular Switch Board of the following sizes complete with three no. suitable size Copper bar with holes (for Ph, N & E) fixed on bakelite/Hard Rubber insulator over the MS welded chairs incl. top cover flushed in wall for housing the board after cutting the brick wall incl. making earthing attachment, painting and mending good damages to building works . |
| 117 | Supply & Fixing 240 V 6 A Modular type switch (Brand approved by EIC) on existing GI Modular type switch board having top cover plate and making necessary connections as required . |
| 118 | Supply & Fixing 240 V, 6A, 5 pin Modular type plug socket (Brand approved by EIC), without switch & plug top, on existing GI Modular type switch board with top cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. |
| 119 | Supply & Fixing 240 V, 16 A, 3 pin Modular type plug socket (Brand approved by EIC) with 16A Modular type switch, without plug top on 4 Module GI Modular typeswitch board with top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wireetc. |
| 120 | Supplying and fixing double-door SPN MCB Distribution Board with IP-42/43 protection, concealed in wall as per GS. 2+12Way[ Legrand ] |
| 121 | Supplying and fixing 240/415 V MCB Isolator on din rail of existing DBs and necessary connection as perGS [Make-Legrand ]40 A DP |
| 122 | Supplying and fixing 240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connectionas per GS [ Make -Legrand ] 6-32 A SP |
| 123 | Cutting Channel of size (43 mm x 43 mm) on masonry wall by Electric operated cutting machine incl. supplying & fixing heavy gauge 25 mm, 3 mm thick Polythene pipewithout earth continuity wire by means of anchoringchemical (Hilti/Sika) and GI \"U\" hooks of 18 SWG mending good damages to original finish by using own tools and tackles. 25 mm dia 3 mm thick polythene pipe without earthcontinuity wire |
| 124 | Supplying and Drawing 1.1 KV single core stranded \"FR\"PVC insulated & unsheathed single core stranded copper wire(Brand approved by EIC) of the following sizes in the prelaid polythene pipe and by the prelaid GI fish wire and making necy. connection as required.2x(1.5 sqmm)+1x(1.5 sqmm) (For seperate plug /Outdoor light) |
| 125 | 2x(1.5 sqmm)+1x(1.5 sqmm) (For seperate plug /Outdoor light) |
| 126 | 2x(2.5 sqmm)+1x(1.5 sqmm) (For Power plug & Computer Plug) |
| 127 | Finishing of the PVC insulated wire ends by socketting with pin/ ring type copper sockets and insulated tapes etc., including supplying sockets, tapes.1.5sqmm[NS] |
| 128 | 2.5sqmm[9 (i)/F-5] |
| 129 | 4 sqmm [9 (ii)/F-5] |
| 130 | 6 sqmm [9 (iii)/F-5] |
| 131 | Supply of2/3.5 Core XLPEInsulated & Sheathed Armoured Aluminium Conductor cables for Working Voltage up to 1100 Volts of following sizes [ Make Polycab / RR Cable /Havells /Gloster]2core 6 Sq. mm (for outdoor light)[ NS ] |
| 132 | 2core 10 Sq. mm[ NS ] |
| 133 | Laying of one No. cable upto 35 sqmm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed |
| 134 | Laying of cable upto 2 core 25sqmmonwall/surface incl. S & F MS saddles with earthing attachment in 2x 10 SWG GI (Hot Dip) Wire, making holes etc. as necy., mending good damages and painting[2(c)/F-1 ] |
| 135 | Supplying and fixing compression type gland thoseforfollowing XLPE / PVC armoured cable (2/4 / 3.5)Core as per GS. 2core 6 Sq. mm (for outdoor light)[ NS ] |
| 136 | 2core 10 Sq. mm[ NS ] |
| 137 | Supplying and fixing crimping type finishing thoseforfollowing XLPE / PVC armoured cable (2/4 / 3.5)Core as per GS. 2core 10 Sq. mm[ NS ] |
| 138 | 2core 6 Sq. mm (for outdoor light)[ NS ] |
| 139 | Sub-Head 6 -Fixing of Light FittingsFixing only single/twin fluorescent light fitting inthe ceilingfixed with “L” type MS clamp as per GS [17/C-2] |
| 140 | Fixing only bulk head ceiling fitting on wall /ceiling by screws etc. [13/ C-2 ] |
| 141 | Fixing only lamp |
| 142 | Supply and delivery of Robust & reliable LED bulk head with IP65 protection & light fitting (bajaj/philips/crompton make) 1K08 impact resistance suitable for surface and wall mounting applications.[ Make: Philips Model no. WT140W LED7S CW PSU SI PC or equvalent of Crompton/Wiprol. |
| 143 | Supply and delivery of Robust & SingleLED Tube light fitting Make-/philipscat no. TZZMC 502 P I x T -LED/Crompton cat no.IGPI6I LTD-16 1 x T8/Wipro Cat No. WI0921208P or equivalent of MAGIK] complete with 18/20 W LED tube lamp.[ Make: Philips Master tube model no. Mas LED Tube 1200mm 18W 865 T8-2100im/ Crompton cat no. LTTD-20/ Wipro Cat No.LL-13-291-650 or equivalent of Magik]. |
| 144 | Supply9W LED lamp to the lamp point. [PHILIPS make] |
| 145 | Supply & Fixing Socket type fan regulator (Step type)(Brand approved by EIC) on existing sheet metal switch board with bakelite/perspex top cover by screw after making housing for regulator knob by cutting bakelite/perspex top cover incl. making necy. connections etc. [ 18 (a) / E-6 ] |
| 146 | Supplying & Fixing MS fan clam of two piece type for RC ceiling as per approved specification, fabricated from 40 mm x 9 mm MS flat including making good damages to building roof with satisfactory finishing and painting – (As per Drawing no. 475 of PWD Specification Book – May 1991) [ 29 / D-14 ] |
| 147 | Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc as per GS[ 21 (a) / C-3 ] |
| 148 | Fixing only exhaust fan after making holes in wall as per GS (12\") |
| 149 | Supply & Fixing louver shutter ( Aluminum)on wall with necy. bolts & nuts (6 mm dia x 62 mm long) as per GS (12\")[ 32(a)/D-14 ](12\") |
| 150 | S & F of 240 V,1200 mm sweep AC celing fan ( Make-CG HS/ Orient Quasar/ Usha Striker) complete with all safety wire & S3 capacitor,downrod,canopy,fork, blades etc.Complete with all accessories |
| 151 | Supply of Exhaustfanscomplete with all accessories having the following Model / Cat No.( Make -EPC )12\" ( 300mm ) Speed 1370 RPM [ NS ]12\" ( 300mm ) Speed 1370 RPM [ NS ] |
| 152 | Sub-Head 10 --Main Swirch,Change over Switch ,MisceleneousS&F 415V L&T 63 A TPN MSFU, Type: FN 63 TPN, on angle iron frame on wall with nuts & bolts etc. including S&F three nos. DIN type HRC type fuse as per rating. [PWD/GS Page No.: D3 Item No.: 4/a ] |
| 153 | Supplying and fixing of 12mm thick Hylam Sheet of size (2ft x 2ft) on wall with 3inch fastner, incl. S& F of 3nos 125A Kit-Kat fuse & 1 no neutral link on the hylam sheet with nuts bolts etc. |
| 154 | Sub-Head 11--- Building Light S&F Street light/Outdoor light/Compound Light Timer DB(Water Proof) concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment and febricated with following items as per instructions ofEIC i) 240 V, 6-32 A SPMCB of breaking capacity 10KA & \"\"C\"\" Charecteristic-- 01 noii) 240V 6-32 A DP MCB Isolator on din rail--- 01 No.iii) 240V , 2P, Power Contractor (rating above 20 Amp) with accessories ----- 01 noiv) Astronomical time switch --- 01nov) Toggle switch for manual/auto operation--- 01no. vi)Double door 2+4 Way SPNDB ---- 1Novii)Necessary connection by copper wire.[Make = ABB, Simens, Legrand, L&T, Havelles or as per EIC] |
| 155 | Supplying and Fixing GI water proof looping cable box having hinged GI Top Cover having 4 mm thick with rubber gasket lining, railway type mechanical locking arrangement, earthing terminal with lug etc. of the following sizes as indicated below, Comprising of one 250 V, 15 A Kit-Kat fuse unit, one NL on porcelain insulator etc. and housing the same in pole muffing incl. addition and alteration to the existing CC muffing (6:3:1) after dismantling the damaged looping cable box etc. where necy. incl. painting. ( 250 x 250 x 100mm ) [16(b)/I-2] |
| 156 | Fixing only outdoor / street light type fluorescent light fitting complete with all accessories to be fixed/projected from the wall of the building incl. making holes to building, S&F 40 mm dia GI pipe (ISI-Medium) 1.50 mts. average length, with GI socket at one end and thread at the other end & suitable bend to house the fitting & making necy. connections with S&F necy. length of 1.5 sqmm PVC insulated single core stranded annealed copper wire and making connections as required and mending good damages to wall and painting[19/C-3] |
| 157 | Supply & delivery of 36 Watt LED STREET Iight fittings with aesthetically designed roadway with execellent thermal management and IP65 protection [ make-PHILIPS/ BRP331 LED36 CW R5N PC PSU S1 V1). |
| 158 | Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the groundevel and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below:By ISI-Medium GI pipe [2a (G-1)] |
| 159 | Supplying & fixing earth busbar including Connecting the equipments of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall as per GS [4(a)/G-2 ] |
| 160 | Connecting the equipments to earth busbar including S & F GI (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damagesSolid GI wireNo 4 S.W.G wire[5(a) ii /G-2 ] |
| 161 | Excavation of soil for installation of Earth Electrode and filling & ramming. For softSoil[ 1(a)/G-1 ] |
| 162 | Supplying & fixing earth busbar including Connecting the equipments of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall as per GS[4(a)/G-2 ] |
| 163 | Add 18% extra in respect of GST on all items (1 to 127), on Rs.3132120.00 |
| 164 | Add 1% extra in respect of Labour Welfare Cess on items no. (1 to 128) 4on Rs.3695902.00 |
