|
| 1 | Supply & Laying of Distribution pipe line (D. I.K-7 / HDPE PE 100, PN 6 / / M.S Pipes 8 mm thick upto 300 mm dia and 10 mm thick for 350 mm and above dia as mentioned in the NIeB) of All types & Classes, including supplying and fixing of ISI markedall types of fittings / specialsrelevant to pipe materials conforming to relevant IS Codes with necessary jointing material rubber gasket including supply ofall types of necessary valves with valve chamber, air valve etc as mentioned in the NIeBincluding earth work in excavation in trenches, shoring (if necessary) of adequate width having minimum depth to keep the top surface of pipe 1.10 mbelow of the existing ground level in any kind of soil mixed with boulder, metal crust, concrete pavement, any road sub-grade and its flank etc., dewatering the trenches, preparing the bottom surface of the trenches for continuous bedding including sand filling (if necessary) &Over-Ground installation to cross small ditches etc. supported with RCC pillars and fitting, fixing, jointing (all types of joints) , specials etc. as per requirement, in position, cutting, chamfering of pipes as required including supply and fitting in position D.I. Specials, thrust blocks as per requirement, filling of the trenches with excavated materials, consolidating the same in layers, guarding trenches with temporary bamboo railing for safety where necessary, emergency horizontal auger boring (for roads other than NH and Railway) where necessary, removing the surplus materials from the site as per Municipal rules in vogue including all material & labour charges, tools and plants, hydraulic pressure testing,and Permanent Roads Restoration as per enclosed drawing as mentioned in the NIeB, cost of construction of Carrier Steel Bridge, ValveandValve Chamber & as per instruction ofE.I.C. of pipe length2.74 KmCourt OHR (Zone-28), Manoj OHR (Zone-9) & Polo OHR (Zone-11) at Asansol Area within Asansol Municipal Corporation. (The Bid is Tunkey Basis. All the works as mentioned in the NIeB will be completed by the bidders. Bidders are requested to see the items of MS pipes, SLuice Valve, Air Release Valve and others fittings and accessories as mentioned in the NIeB rates will be included in rate of these following items) |
| 2 | HDPE PIPE (PE 100, PN 6) 110 MM DIA |
| 3 | HDPE PIPE (PE 100, PN 6) 160 MM DIA |
| 4 | Supplying and febricating of M.S PIPE 300 MM DIA |
| 5 | Supplying, fitting and fixing of C.I. Mechanical Compression flexible Collar Couplings suitable for C.I. Spun Pipes (as per IS: 1536) and D. I. Pipes (as per IS: 8329) complete with Sealing Rubber Gasket of EPDM quality (IS:5382/1985 Type - 4), Cast Iron Follower Glands and Mild Steel Nut Bolts (Zinc Coated). The whole assembly should be mechanically and hydraulically tested to the provisions as laid down in IS: 1538. Fitting and fixing should be in proper position with proper care of main pipe line for leak proof condition. 300 mm dia |
| 6 | Supplying, fitting and fixing of C.I. Mechanical Compression Long Sleeve Collar Coupling (popularly known as Cut-N-Repair Coupling) suitable for jointing C.I. Spun Pipes (as per IS: 1536) and D.I. Pipes (as per IS: 8329) with BS:1211 Class-B Pipes. The Couplings will be supplied complete with Sealing Rubber Gasket of EPDM quality (IS:5382/1985 Type-4), Cast Iron Follower Glands and Mild Steel (Zinc Coated) Nut Bolts . The whole assembly should be mechanically and hydraulically tested to the provisions as laid down in IS: 1538. Fitting and fixing should be in proper position with proper care of main pipe line for leak proof condition. 450 mm with length 400 mm |
| 7 | Cost iron double flanged manually operated sluice valves generally conforming to IS 14846 : 2000, having four faces and spindle nut of gunmetal, inside screw non- rising type quality gunmetal /AISI 410 spindle: seat tested to 10kg/CM2 and body tested to 15kg/CM2, flanges flat faced and drilled to 1S. : 1538 : 1993. Painted black all over with asphalt base paint. Valves tested by closed end method. 300 mm dia |
| 8 | Cost iron double flanged manually operated sluice valves generally conforming to IS 14846 : 2000, having four faces and spindle nut of gunmetal, inside screw non- rising type quality gunmetal /AISI 410 spindle: seat tested to 10kg/CM2 and body tested to 15kg/CM2, flanges flat faced and drilled to 1S. : 1538 : 1993. Painted black all over with asphalt base paint. Valves tested by closed end method. 350 mm dia |
| 9 | Cost iron double flanged manually operated sluice valves generally conforming to IS 14846 : 2000, having four faces and spindle nut of gunmetal, inside screw non- rising type quality gunmetal /AISI 410 spindle: seat tested to 10kg/CM2 and body tested to 15kg/CM2, flanges flat faced and drilled to 1S. : 1538 : 1993. Painted black all over with asphalt base paint. Valves tested by closed end method. 450 mm dia |
| 10 | Supplying including cost of installation of C.I. Mechanical joint Tee as dimensionally described in IS:13382/2004. Each Tee consists of One C.I. Body, Two C.I. Follower Glands, Two sealing Rubber Gaskets of EPDM quality (Conforming to IS:5382/1985 Type-4) and Zinc coated M.S. Fasteners. The Branch Flange is drilled as per IS: 1538. The whole assembly is mechanically and hydraulically tested to provisions as laid down in IS:13382 /2004. Diameter in mm 13382/2004.150 X 150 X 150 |
| 11 | Supplying including cost of installation of C.I. Mechanical joint Tee as dimensionally described in IS:13382/2004. Each Tee consists of One C.I. Body, Two C.I. Follower Glands, Two sealing Rubber Gaskets of EPDM quality (Conforming to IS:5382/1985 Type-4) and Zinc coated M.S. Fasteners. The Branch Flange is drilled as per IS: 1538. The whole assembly is mechanically and hydraulically tested to provisions as laid down in IS:13382 /2004. Diameter in mm 13382/2004.250 X 250 X 150 |
| 12 | Supplying including cost of installation of C.I. Mechanical joint Tee as dimensionally described in IS:13382/2004. Each Tee consists of One C.I. Body, Two C.I. Follower Glands, Two sealing Rubber Gaskets of EPDM quality (Conforming to IS:5382/1985 Type-4) and Zinc coated M.S. Fasteners. The Branch Flange is drilled as per IS: 1538. The whole assembly is mechanically and hydraulically tested to provisions as laid down in IS:13382 /2004. Diameter in mm 13382/2004.300 X 300 X 300 |
| 13 | Supplying including cost of installation of C.I. Mechanical joint Tee as dimensionally described in IS:13382/2004. Each Tee consists of One C.I. Body, Two C.I. Follower Glands, Two sealing Rubber Gaskets of EPDM quality (Conforming to IS:5382/1985 Type-4) and Zinc coated M.S. Fasteners. The Branch Flange is drilled as per IS: 1538. The whole assembly is mechanically and hydraulically tested to provisions as laid down in IS:13382 /2004. Diameter in mm 13382/2004.300 X 300 X 150 |
| 14 | Supplying including cost of installation of C.I. Mechanical joint Tee as dimensionally described in IS:13382/2004. Each Tee consists of One C.I. Body, Two C.I. Follower Glands, Two sealing Rubber Gaskets of EPDM quality (Conforming to IS:5382/1985 Type-4) and Zinc coated M.S. Fasteners. The Branch Flange is drilled as per IS: 1538. The whole assembly is mechanically and hydraulically tested to provisions as laid down in IS:13382 /2004. Diameter in mm 13382/2004.350 X 350 X 300 |
| 15 | Supplying including cost of installation of C.I. Mechanical joint Tee as dimensionally described in IS:13382/2004. Each Tee consists of One C.I. Body, Two C.I. Follower Glands, Two sealing Rubber Gaskets of EPDM quality (Conforming to IS:5382/1985 Type-4) and Zinc coated M.S. Fasteners. The Branch Flange is drilled as per IS: 1538. The whole assembly is mechanically and hydraulically tested to provisions as laid down in IS:13382 /2004. Diameter in mm 13382/2004.450 X 450 X 150 |
| 16 | Supplying, fitting and fixing of C.I. Mechanical flexible Flange Socket Tailpiece suitable for making flanged connection with the plain barrel of C.I. Spun Pipes (as per IS : 1536) and D.I. Pipes (as per IS : 8329). The Tailpieces to be supplied complete with Sealing Rubber Gasket of EPDM quality (IS:5382/1985 Type-4), Cast Iron Follower Glands and Mild Steel Nut Bolts (Zinc Coated). The whole assembly should be mechanically and hydraulically tested to the provisions as laid down in IS: 1538. Fitting and fixing should be in proper position with proper care of main pipe line for leak proof condition. 350mm with length 150mm |
| 17 | Supplying, fitting and fixing of C.I. Mechanical flexible Flange Socket Tailpiece suitable for making flanged connection with the plain barrel of C.I. Spun Pipes (as per IS : 1536) and D.I. Pipes (as per IS : 8329). The Tailpieces to be supplied complete with Sealing Rubber Gasket of EPDM quality (IS:5382/1985 Type-4), Cast Iron Follower Glands and Mild Steel Nut Bolts (Zinc Coated). The whole assembly should be mechanically and hydraulically tested to the provisions as laid down in IS: 1538. Fitting and fixing should be in proper position with proper care of main pipe line for leak proof condition. 300mm with length 125mm |
