Tender For Construction Of Eklavya Model Residential School Including Site Development Works At Pangi At Killar Dharwas Tehsil Pangi District Chamba Hp Sh Two Nos. Of Studio Apartments Transit Accommodation Including Site Development (Civil And Elec
Tender Value
6.12 Crore
Estimated cost
Bid Submission
28 Jan 2025
0 days left
EMD
12.25 Lakhs
Bank guarantee accepted
Document Fee
1770
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
pangi → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Eklavya Model Residential School Including Site Development Works At Pangi At Killar Dharwas Tehsil Pangi District Chamba Hp Sh Two Nos. Of Studio Apartments Transit Accommodation Including Site Development (Civil And Electrical Work
BOQ
| Sl. No. | Item Description |
| 1 | Sub-Head - Earth Work |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. |
| 3 | a) All kinds of soil |
| 4 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50 m and lift up to 1.5m, as directed by Engineer-in-Charge. |
| 5 | a) Ordinary rock |
| 6 | b) Hard rock (blasting prohibited) |
| 7 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 8 | a) All kinds of soil. |
| 9 | Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m. |
| 10 | a) Ordinary rock |
| 11 | b) Hard rock (requiring blasting) |
| 12 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : |
| 13 | All kinds of soil |
| 14 | Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 15 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 16 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 17 | Sub-Head - Concrete Work |
| 18 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 19 | a) 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). |
| 20 | b) 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 21 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing : |
| 22 | a) 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 23 | Centering and shuttering including strutting, propping etc. and removal of form work for : |
| 24 | Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.. |
| 25 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources). |
| 26 | Providing and applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. |
| 27 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling & dressing & finishing the top smooth. |
| 28 | Providing and laying in position with cement concrete of mix 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) using 15% plum/ stone boulders of specified grade and size and curing complete excluding cost of centring and shuttering,in retaining walls and breast wall.The size of plum will be usually be 150 to 300 mm as per the direction of Engineer-in-Charge. |
| 29 | Sub-Head - Reinforced Cement Concrete |
| 30 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : |
| 31 | a) 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 32 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : |
| 33 | a) 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 34 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources). |
| 35 | Centering and shuttering including strutting, propping etc. and removal of form for : |
| 36 | Foundations, footings, bases of columns, etc. for mass concrete |
| 37 | Suspended floors, roofs, landings, balconies and access platform |
| 38 | Shelves (Cast in situ) |
| 39 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 40 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 41 | Stairs, (excluding landings) except spiral-staircases |
| 42 | Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like |
| 43 | Edges of slabs and breaks in floors and walls |
| 44 | Under 20 cm wide |
| 45 | Weather shade, Chajjas, corbels etc., including edges |
| 46 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto all floor level. |
| 47 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 48 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections |
| 49 | Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand). |
| 50 | Sub-Head - Masonry Work |
| 51 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 52 | a) Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 53 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : |
| 54 | a) Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 55 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. |
| 56 | a) Cement mortar 1:4 (1 cement :4 coarse sand) |
| 57 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.ird course of half brick masonry. |
| 58 | Providing and laying broken autoclaved aerated cement (AAC) blocks and/or bats (light weight, having density 550-650 kg/m3) of nominal size 25mm to 65mm in the sunken portion of toilets upto floor five level all complete as per the direction of Engineer-in-charge. |
| 59 | Sub-Head - Stone Work |
| 60 | Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level with : |
| 61 | Cement mortar 1:6 (1 cement : 6 coarse sand). |
| 62 | Supplying & Filling with stone boulders of size 150 to 300 mm in plum concrete of retaining wall complete as per the direction of the Engineer-in-charge. ( Note :- 30% deduction shall be made for voids in boulder filling) |
| 63 | Providing and fixing 75 mm dia Rigid PVC pipe (working pressure 4kg./sqcm.) conforming to IS : 13592 type A in retaining walls for use as weep holes, laid to required slope complete as per the directions of the Engineer-in-charge. |
| 64 | Sub-Head : Cladding Work |
| 65 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. |
| 66 | a) Granite stone slab colour black, Cherry/Ruby red |
| 67 | (i) Area of slab upto 0.50 sqm |
| 68 | Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete |
| 69 | Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinalpartitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finishedsmooth. |
| 70 | a) Granite Stone of approved shade |
| 71 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 72 | Sub Head-Wood & PVC Work |
| 73 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia. & length (hold fast lugs or dash fastener shall be paid for separately). |
| 74 | a) Second class teak wood |
| 75 | Extra for providing frosted glass panes 4 mm thick (weight not less than 10 kg per sqm) instead of ordinary float glass panes 4 mm thick (weight not less than 10 kg per sqm) in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). |
| 76 | Providing and fixing BWP grade factory machine pressed pre-laminated flush door shutters of exterior grade with teak wood lippingon edgesas per IS:2202-Part 1of approved make core of block board construction with frame of 1st class hard wood and well matched 1 mm thick high pressure decorative laminationconfirming to IS :2046 -95 above 3 ply veneeringon both faces of shutters with high density protective surfacelayer and reverse side of adhesive bonding quality conform to IS:2046 Type-S : |
| 77 | a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 78 | Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). |
| 79 | Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25 mm with two chromium plated brass brackets fixed withC.P. brass screws and PVC sleeves etc., wherever necessary complete : |
| 80 | a) 25 mm dia |
| 81 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) |
| 82 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight up to 35 kg and door width up to 700 mm) with necessary accessories and screws etc. complete. |
| 83 | Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm fixed with wooden adhesive of approved quality and screws/ nails on the edges of the Pre-laminated particle board as per direction of Engineer-in-charge. |
| 84 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : |
| 85 | a) 35 mm thick shutters. |
| 86 | (i) with ISI marked M.S. pressed butt hinges bright finished of required size - Second class teak wood |
| 87 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. |
| 88 | a) Second class teak wood |
| 89 | (i) 30 mm thick |
| 90 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. |
| 91 | Fixed to openings /wooden frames with rawl plugs screws etc. |
| 92 | Providing and fixing Stainless steel sliding door boltstransparent or dyed to required colour or shade with nuts and screws etc. complete : |
| 93 | a) 300x16 mm |
| 94 | b) 250x16 mm |
| 95 | Providing and fixing SStower bolts transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 96 | a) 250x10 mm |
| 97 | b) 150x10 mm |
| 98 | Providing and fixing stainless steel handlestransparent or dyed to required colour or shade with necessary screws etc. complete : |
| 99 | a) 125 mm |
| 100 | b) 100 mm |
| 101 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 102 | a) Twin rubber stopper |
| 103 | Providing & Fixingglass panes, with wooden fillets: |
| 104 | a) Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm). |
| 105 | Providing M.S. Piano hinges ISI marked IS : 3818 finished with nickel chromium plating grade 1 as per IS: 1068 and fixing with necessaryscrews etc., complete. |
| 106 | a) Overall width 35 mm |
| 107 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. |
| 108 | a) 1.0 mm thick. |
| 109 | Providing & Fixinglaminated sheet of in white / ivory shade of Century/Greenply/Merino make, inside of cupboard etc. with adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. |
| 110 | a) 0.8 mm thick. |
| 111 | Providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer-in-charge. |
| 112 | Providing and fixing MS powder coated set of five pegs (Hooks) of approved quality with MS screws all complete as per direction of the Engineer-in-charge . |
| 113 | P/F PVC rubber Silencer on the rear side of door shutter to avoid collision between wall and door shutter as per directions of Engineer in Charge. |
| 114 | Providing and fixing BWP Ply board conforming to IS: 710 of of Merriono/ Greenply/ Century/Archid/Kitply , bonded with phenolformaldehyde synthetic resin in cupboards, shelves, shutters with necessary screws, nails and adhesive etc. all complete as per the direction of Engineer-in-charge |
| 115 | a) 18 mm thick |
| 116 | Providing and fixing 6mm thick BWP grade commercial ply of Merriono/ Greenply/Century/ Archid/ Kitply , bonded with phenolformaldehyde synthetic resin in backing ofcupboards, shelves, shutters with necessary screws, nails and adhesive etc. all complete as per the direction of Engineer-in-charge |
| 117 | a) 6 mm thick |
| 118 | Sub-Head - Steel Work |
| 119 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 120 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 121 | a) In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete. |
| 122 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 123 | Sub-Head - Flooring |
| 124 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 125 | a) 40 mm thick with 20 mm nominal size stone aggregate |
| 126 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete. |
| 127 | Providing and laying full body & unglazed vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 128 | a) Size of Tile 600x600 mm |
| 129 | Providing and laying Full body and unglazedVitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make in all colours & shade in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. |
| 130 | a) Size of Tile 600x600 mm |
| 131 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade(0.10 kg of hardener and 0.20 kg of resin per kg), including filling/grouting and finishing complete as per direction of Engineer-in-charge. |
| 132 | a) Size of Tile 600x600 mm |
| 133 | Deduct for not grouting the joints with white cement and matching pigment in the items of fixing of vitrified tiles . |
| 134 | Providing and layingGVTvitrified floor tiles of approvedin smooth finish Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622, in all colours & shade in wall liningover 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including using PVC spacer 2 to 3 mm thick and after removing the spacers,the joints shall be filled using epoxy grout mix of 0.7 kg of organic coated filler of desired shade , 0.1 Kg of hardner and 0.2 kg of resin per kg of grout and finishing all complete as per direction of E-In-Charge. |
| 135 | a) Size of Tile1200x600 mm |
| 136 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. |
| 137 | a) Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent |
| 138 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. |
| 139 | a) Glazed Vitrified tiles Matt/Antiskid finish of size |
| 140 | (i) Size of Tile 600 x 600 mm |
| 141 | Sub-Head - Roofing |
| 142 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 143 | (i) Single socketed pipes. |
| 144 | a) 110 mm diameter |
| 145 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 146 | a) Coupler |
| 147 | (i) 110 mm |
| 148 | b) Bend 87.5° |
| 149 | (i) 110 mm bend |
| 150 | C) Shoe (Plain) |
| 151 | (i) 110 mm Shoe |
| 152 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 153 | a) 110 mm |
| 154 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /seIf tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 155 | Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : |
| 156 | a) Ridges plain (500 - 600mm) |
| 157 | b) Flashings/ Aprons.( Upto 600 mm) |
| 158 | C) Barge board (Upto 300 mm) |
| 159 | d) Gutter (600 mm over all girth) |
| 160 | Sub-Head - Finishing |
| 161 | Rough cast plaster upto 10 m height above ground level with a mixture of sand and gravel or crushed stone from 6 mm to 10 mm nominal size, dashed over and including the fresh plaster in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand) and top layer 10 mm cement plaster 1:3 (1 cement: 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement. |
| 162 | Ordinary cement finish using ordinary cement |
| 163 | 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement: 5 coarse sand) finished with a top layer 6mm thick cement plaster 1:6 (1 cement: 6 fine sand). |
| 164 | 15 mm cement plaster on rough side of single or half brick wall of mix : |
| 165 | a) 1:6 (1 cement: 6 coarse sand) |
| 166 | Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. |
| 167 | a) 12 mm cement plaster |
| 168 | Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. |
| 169 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer, of required shade and colour all complete : |
| 170 | a) New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre |
| 171 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade |
| 172 | a) New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 173 | Applying priming coat : |
| 174 | a) With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works |
| 175 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 176 | a) Two or more coats on new work. |
| 177 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: |
| 178 | a) Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. |
| 179 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 180 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 181 | Providing & fixing G.I. chicken wire mesh of nominal size upto 20mm having 24 gauge thick with G.I. nails etc. to wall surface of dissmilar material viz RCC and brick work etc.all complete. |
| 182 | Sub-Head - Sanitary Installations |
| 183 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required : |
| 184 | a) W.C. pan with ISI marked white solid plastic seat and lid |
| 185 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : |
| 186 | a) Single half stall urinal with 5 litre P.V.C. automatic flushing cistern |
| 187 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: |
| 188 | a) White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap |
| 189 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 190 | a) Kitchen sink without drain board |
| 191 | (i) 610 x 460 mm bowl depth 200 mm. |
| 192 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 193 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 194 | a) Flexible pipe |
| 195 | (i) 32 mm dia |
| 196 | Providing and fixing toilet paper holder : |
| 197 | a) C.P. brass |
| 198 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. |
| 199 | a) Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms. |
| 200 | Providing and fixing PTMT Bottle Trap for Wash basin and sink. |
| 201 | a) Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms |
| 202 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 203 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 204 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 205 | Providing and Fixing PVC soil waste and vent pipes of pressure 6Kg/sqcm. including jointing with approval solvent. |
| 206 | (i) 110 mm Dia Pipes |
| 207 | Providing and fixing galvanised Iron holding down clamps for SWR PVC /sand cast iron/centrifugally cast (spun) iron pipes and fixing with galvanised iron screwed rodwith nuts , bolts and anchor bolts fastners in the ceiling complete in all respect. |
| 208 | a) For 110 mm diameter. |
| 209 | Providing and fixing plain bend of required degree. |
| 210 | a) 110 mm dia (SWR PVC). |
| 211 | Providing and fixing Door bend of required degree. |
| 212 | a) 110 mm dia (SWR PVC). |
| 213 | Providing and fixing single equal plain junction of required degree. |
| 214 | a) 110x110x110 mm(SWR PVC) |
| 215 | Providing and fixing single equaljunction with acess door of required degree. |
| 216 | a) 110x110x110 mm(SWR PVC) |
| 217 | Providing and fixing terminal guard: |
| 218 | a) 110 mm(SWR PVC) |
| 219 | Providing and fixing Collar: |
| 220 | a) 110 mm (For SWR PVC Pipe): |
| 221 | Providing and fixing PVC Floor trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : |
| 222 | a) 110 mm inlet and 110 mm outlet |
| 223 | Providing and fixing Stainless Steel (SS) 304 gradewall mounted towel ring square shape 157 mm long, 445 mm wide and 569 mm heightwith concealed fittings arrangement of approved make , weighing not less than 560 gms. |
| 224 | Providing and fixing Stainless Steel (SS) 304 gradetowel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved make all complete as per direction of Engineer-in-Charge. |
| 225 | a) 600 mm long towel rail with total length of 520 mm, width 88 mm and effective height of 50 mm, weighing not less than 500 gms. |
| 226 | Providing and fixing 100 mm Dia stainless steel grating with frame (with or without hole) . |
| 227 | Sub-Head : Water Supply |
| 228 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall |
| 229 | a) 20 mm nominal outer dia. Pipes. |
| 230 | b) 25 mm nominal outer dia .Pipes. |
| 231 | c) 32 mm nominal outer dia .Pipes. |
| 232 | d) 40 mm nominal outer dia .Pipes. |
| 233 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. |
| 234 | a) 15 mm nominal outer dia .Pipes. |
| 235 | b) 20 mm nominal outer dia .Pipes. |
| 236 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work |
| 237 | a) 32 mm nominal outer dia. Pipes. |
| 238 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : |
| 239 | a) 25 to 40 mm nominal bore |
| 240 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)Gate Valve in Chlorinated Polyvinyl Chloride (CPVC)pipe etc. complete (New work): |
| 241 | a) 25 mm nominal bore |
| 242 | b) 20 mm nominal bore |
| 243 | c) 32 mm nominal bore |
| 244 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : |
| 245 | a) 15 mm nominal bore |
| 246 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 247 | a) 45 cm length |
| 248 | (i) 15 mm nominal bore |
| 249 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : |
| 250 | a) 100 mm diameter |
| 251 | Providing and filling sand of grading zone V or coarser grade all- round the CPVC pipes in external work. |
| 252 | a) 32 mm diameter pipe |
| 253 | Providing and fixing CPVC Union in CPVC pipe including cutting and threading the pipe and making long screws etc. complete (New work). |
| 254 | a) CPVC Union 20 mm |
| 255 | b) CPVC Union 25 mm |
| 256 | c ) CPVC Union 32 mm |
| 257 | d) CPVC Union 40 mm |
| 258 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 259 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: |
| 260 | a) 15 mm nominal bore. |
| 261 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. |
| 262 | a) 15 mm nominal bore. |
| 263 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 264 | a) 15 mm nominal bore. |
| 265 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 266 | a) 15mm nominal bore |
| 267 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. |
| 268 | Providing and fixingJaiquar/Kohler/Hindware or equivalentSoap Dish holder ,SS 304 Stainless Steel, Brushed Steel Finish, 12.3cm x 12.15cm x 4.65cm LBH, easy to use Ergonomic Design, 23kg Load Bearing Capacity with conealed fitting arrangements.all complete as per direction of Engineer-in-charge. |
| 269 | Providing and fixing C.P. brass Sink Mixer ofapproved quality as per direction of Enginner in charge. |
| 270 | a) 15 mm nominal bore |
| 271 | Sub-Head : Drainage |
| 272 | Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : |
| 273 | a) 200 mm diameter |
| 274 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design: |
| 275 | a) 200 mm diameter S.W. pipe |
| 276 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : |
| 277 | a) 100x100 mm size P type |
| 278 | (i) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 279 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2coarse sand : 4 graded stone aggregate 20 mm nominal size),foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design : |
| 280 | a) Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg(weight of cover 23 kg and weight of frame 15 kg) : |
| 281 | (i) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 282 | Extra for depth for manholes |
| 283 | a) Size 90x80 cm |
| 284 | (i) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 285 | Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : |
| 286 | a) With 20x20 mm square bar |
| 287 | Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : |
| 288 | a) For pipes 100 to 250 mm diameter |
| 289 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 290 | a) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 291 | Sub-Head : Aluminium Work |
| 292 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 293 | a) For fixed portion |
| 294 | i) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 295 | b) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). |
| 296 | i) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 297 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. |
| 298 | a) Pre-laminated particle board with decorative lamination on both sides. |
| 299 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 300 | a) With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm) |
| 301 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg., for doors, including cost of cutting floors ,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. |
| 302 | a) With stainless steel cover plate minimum 1.25 mm thickness. |
| 303 | Providing and fixing Brass 100 mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 304 | Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineer-in-charge |
| 305 | a) Powder coated minimum thickness 50 micron aluminium |
| 306 | Sub-Head : Water Proofing |
| 307 | Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: |
| 308 | (i)Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. |
| 309 | (ii)IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. |
| 310 | (iii)IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. |
| 311 | (IV) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm). |
| 312 | Electrical Works |
| 313 | SUB HEAD-I(Interna Wiring) |
| 314 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 315 | a) Group A |
| 316 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 317 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 318 | Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 319 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. |
| 320 | a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 321 | b) 4 X 1.5 sq. mm + 2 X 1.5 sq. mm earth wire |
| 322 | c) 2 X 10 sq. mm + 1 X 6 sq. mm earth wire |
| 323 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. |
| 324 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required. |
| 325 | Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. |
| 326 | SUB HEAD-II (Distribution System) |
| 327 | Supplying and fixing following way, horizontal type SPN , sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with metal door, tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) (Make-Havells -Metallica ) |
| 328 | a) 12 Way SPNDouble Door (CAT No-DHDNSHODAW12 ) |
| 329 | b) 16 Way SPNDouble Door (CAT No-DHDNSHODAW16 ) |
| 330 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, having provision ofmounting MCCB upto 125A as incomer complete with making interconnection etc as required. (but without outgoing MCBs and incomer MCCB ) (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) (Make:- ( Make L&T-PHV306DYM or Similar Superior make) |
| 331 | a) 6 way (6+6+6), Double door |
| 332 | Supplying and fixing following rating, 240/415 volts, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 333 | a) 5 amps to 32 amps, 240 volts Single pole. |
| 334 | b) 40 amp SP MCB |
| 335 | c) Double Pole 6-32A |
| 336 | d) Double Pole 40A |
| 337 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 338 | a) 25 amps |
| 339 | b) 40 amps |
| 340 | S/F Following rating and breaking capacity Three Pole MCCBwith thermomagnetic release and terminal spreaders in the existing vertical DB i/c making interconnection with existing Bus Bar etc as required. |
| 341 | a) 125A 16KA |
| 342 | Supplying and fixing Cable End Box ( IP 43 ) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required. |
| 343 | a) For 10 way, Double door SPN MCBDB |
| 344 | b) For 14 way, Double door SPN MCBDB |
| 345 | Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 346 | SH-III (Telephone, Television Wiring & Conduting Only) |
| 347 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. |
| 348 | a) 1 or 2 Module (75mmX75mm) |
| 349 | b) 3 Module (100mmX75mm) |
| 350 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 351 | a) 5/6 amps switch |
| 352 | b) 3 pin 5/6 amp socket outlet |
| 353 | c) Telephone Socket outlet. |
| 354 | d) TV Antenna socket outlet. |
| 355 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 356 | a) 20mm |
| 357 | b) 25mm |
| 358 | Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, Unarmored Telephone cable in the existing surface/ recessed steel/ PVC conduit as required. |
| 359 | a) 2 Pair |
| 360 | Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. |
| 361 | a) 1 run of cable |
| 362 | SUB HEAD-IV (Earthing ) |
| 363 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories,and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. ( For L.A.) |
| 364 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt ) as required. |
| 365 | Supplying and laying 25 mm X 5 mm G.I strip on surface or in recess etc as required. |
| 366 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. |
| 367 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. |
AI Tender Summary
Tender Timeline
Jan 13, 2025
11:30 IST
Tender Published
Tender notice published.
CompletedJan 28, 2025
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedFeb 03, 2025
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender