Tender For Supply Of Equipments For Industrial Drives And Control Laboratory, uthangarai-Tamil Nadu

Supply Of Equipments For Industrial Drives And Control Laboratory , List Of Equipments , Voltage Current And Power Measurement In Single Phase Ac Circuit Measurement Of Power By Using Various Loads . Analog Voltmeter 0-300V Ac Panel Mounted . Analog Ammeter 0-5A Ac Panel Mounted . Analog Wattmeter 1.5Kw Ac Panel Mounted . Single Digital Power Monitor To Measure Power . Single Phase Ac Lamp Load 230V/5A 1Kw . Panel Enclosure With Iylem Front Panel With Input/Output Terminal Outlets , Construct Led Circuit With Current Limiting Resistor . Power Source 0-9V Variable Dc . Led 3Mm White . Led 3Mm Rgb . Variable Resistance . Pcb Mounted With Terminal Outlets And Box Enclosure , Construct Dc Regulated Power Supply Unit Dc Power Supply Circuit With Discrete Components To Assemble And Test The Voltage And Different Waveforms With Transformer,Diodes, Regulator Ic 5V/12V Dc , Pcb And Box Enclosure , Demonstrate The Working Of Mcb And Elcb Demonstration And Testing Of Mcb And Elcb By Short Circuit Test, Earth Fault Test And Load Test By Using Lamp Load . Single Pole Mcb 2-5Amps . Two Pole Elcb 30Ma . Lamp Load Single Phase 5Amps . Panel Enclosure And Terminal Outlets , Logic Gate Using Ics . Built-In Power Supply Dc +5 V @ 500 Ma . On Panel Gates : 4 Nand Gates (7400), 4 Nor Gates (7402), . 4 And Gates (7408), 4 Or Gates (7432) & 6 Not Gates (7404) . 5 Logic Input Switches With Green Led Display . 5 Logic Output Red Led Display . Required Numbers Of Patch Cords And Operating Manual , Speed Control Of Induction Motor Using Vfd . Speed Control Of Induction Motor By Using Vfd Ac Drive Setup With Three Phase Squirrel Cage Induction Motor 0.5Hp/220V/1440Rpm . This Unit Consists Of Delta Or Equivalent Make Igbt Based 3-Ph V/F Drive Suitable For 0.5Hp/230V Induction Motor. . The Ac 1-Phase Input Terminals, Motor Output Terminals Points Are Brought Out On The Front Panel. . A 2Pole / 6Amps Mcb Is Provided To Switch On/Off The Ac Mains Supply To The Unit And Also For Protection. . The Drive Has The Facility To Change The Frequency With Constant V/F(Variable Voltage Variable Frequency) To Vary The Speed Of The Induction Motor Since The Speed Is Directly Proportional To The Frequency. . Voltage, Output Current, And Frequency. . Switch For Forward And Reverse Direction Of Rotation. , Direction Control Of Dc Motor Using Driver Ic L293d Arduino Based Direction Control Of Dc Motor Using L293d Driver Control Which Can Control A Set Of Two Dc Motors Simultaneously In Any Direction. Specification: ? Cpu: Atmega328p Mcu (Dip Package). ? L293d Driver Circuit ? Dc Motor 5V ? Forward/Reverse Switches Software Support: ? Arduino Ide Package Include: ? Trainer Kit. ? Usb Cable. ? 12V/1A Adaptor ? 2Mm Patch Cord , “Lt” Stepper Motor Drive Kit With Digital Controller Speed Control Of Stepper Motor :- This Unit Is Microcontroller Based Controller Circuit To Accurately Generates Pulses To Energize The Stepper Motor Winding In The Desired Sequence. Power Transistor Based Driver Ckt. To Drive The Stepper Motor, 2X16 Lcd Display To Set And Display The Parameters, And Able To Set The Speed Of The Motor In Rpm, Number Of Steps Motor Can Move, Direction Of Rotation – Forward And Reverse Direction With Half Step And Full – Step Mode.The Stepper Motor Fitted On The Panel And All The Connections Are Brought To A Connector. The Dial Is Fitted To The Shaft Of The Stepper Motor. The Inner Dial Marking In Steps And Outer Marking In Degrees. Step Angle : 1.80 + / – 0.10 3 Kg Cm = 0.1 Nm Steps Per Revolution : 200 Half Step = 0.90. Mains Operated. => Limited

INR 104607 /-

INR 1047.0 /-

Refer document