|
| 1 | Cleaning junglesincluding uprooting of trunk vegetation grass, bushes, wood trees and sapling of girth upto 30cm measured at a height of 1 meter above ground level and removal of rubbish upto a distance of 50m outside the periphery of area cleared. UPPWD SOR-2022 SI No 259 |
| 2 | Earth work in excavation in foundation trenches in ordinary soil(Loam,Clay or Sand) including laft upto 1.50 M and lead up to 30m and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and the side of the foundation trenches ot into the plinth and rewmoval and disposal of surplus Earth as directed by the engineer-in-charge up to a distance of 30m from the foundation trenches.SI No 251 page 25 |
| 3 | Cement Concrete with 4 cm. gauge stone ballast, fine sand of 1.25 F.M. & cement in proportion of 10:5:1 in foundation & under floors including supply of all matedkrials. labour. Tools & plants etc. required for proper completion of the work SI NO 274 SOR 2022 page 27 |
| 4 | Brick work with common burnt clay F.P.S (non modular) bricks of class Mdesignation -100 class brickwork 1:4 Cement and Coarse sand for foundation and PlinthUPPWD SOR 2022SI no 6.1.1 page 30 |
| 5 | Brick work with common burnt clay F.P.S (non modular) bricks of class designation -100 class brickwork 1:4 Cement and Coarse sand for Super Structure UPPWD SOR 2022SI no 6.4.1 page 30 |
| 6 | 12mm thick cement plasteron brick work with cement mortar of mix 1:4 (1cement:4Coarse sand) UPPWD SOR 2022 SI no 584 (ii)page 55 |
| 7 | 15mm thick cement plasteron rough side og single or half brick wallwith cement mortar of mix 1:4 (1cement:4Coarse sand) UPPWD SOR 2022 SI no 2new page 55 |
| 8 | Finishing wall (Two Coat ) with exteriorpaint (Apex) of approved brand and manufacture and of required shade on undercoated wall surface to give even shade including one coat of primer applied curing cost of all material labour T&P etc.UPPWD SOR 2022 SI No 21new Page 63 |
| 9 | Painting two coat orincluding preparing the surface by thoroughly clearingthe surface of all dirt dust and scrapping and papering Including cost of all material labour T&P etc required for proper completion of work.UPPWD SOR 2022 SI no (2New+3New)(33+80)=113 Page 61 |
| 10 | Supply and Fixing of Rest Chair Bench |
| 11 | Concrete with 2 cm. Gauge approved stone ballast, coarse sand and cement in foundation and under floors in the proportion of 4:2:1 including supply of all materials, labour, Tools & plants etc. Required for proper completion of the work.SI No 279 SOR 2022 |
| 12 | Construction of sub grade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table no, 300-2 Carted earth 8 km. As per MORTH Specification 305/SI No 3.18 |
| 13 | Concrete with 2 cm. Gauge approved stone ballast, coarse sand and cement in foundation and under floors in the proportion of 4:2:1 including supply of all materials, labour, Tools & plants etc. Required for proper completion of the work.SI No 279 SOR 2022 |
| 14 | PART-B |
| 15 | Providing and fixing Arm and Shoulder Wheel of size 1300x1200x1350 mm make of Green Gym or Equivalent fabricated with main post of 140mm dia and 3.0 mm thick rest of the pipe are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tabular steel and hot dipped galvanized, and powder coated using Akzo nobel or equivalent of 80-120 micron thick. All welding joint of pipe are robotic welded with joint scalloped as necessary and dressed off removing sharp egde and burrs. Zinc primer paint to be applied at all welding points prior to finishing Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-In-Charge. Equipment to be fitted within built limiter to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolt and once the concrete is set, fix the equipment on to it and cover nuts and bolt with the base plate cover, all complete as per direction and approval of Engineer-In-Charge regarding material shape of equipment colour on metal, seat and base cover plate and fixing of equipment etc. |
| 16 | Providing and fixingof Chin up Bar size 26300x305x2640 mm make of Green Gym or Equivalent fabricated with main post of 140mm dia and 3.0 mm thick rest of the pipe are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tabular steel and hot dipped galvanized, and powder coated using Akzo nobel or equivalent of 80-120 micron thick. All welding joint of pipe are robotic welded with joint scalloped as necessary and dressed off removing sharp egde and burrs. Zinc primer paint to be applied at all welding points prior to finishing Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-In-Charge. Equipment to be fitted within built limiter to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolt and once the concrete is set, fix the equipment on to it and cover nuts and bolt with the base plate cover, all complete as per direction and approval of Engineer-In-Charge regarding material shape of equipment colour on metal, seat and base cover plate and fixing of equipment etc. |
| 17 | Providing and fixing Sit Up Stationof size 1500x1150x650 mm make of Green Gym or Equivalent fabricated with main post of 140mm dia and 3.0 mm thick rest of the pipe are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tabular steel and hot dipped galvanized, and powder coated using Akzo nobel or equivalent of 80-120 micron thick. All welding joint of pipe are robotic welded with joint scalloped as necessary and dressed off removing sharp egde and burrs. Zinc primer paint to be applied at all welding points prior to finishing Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-In-Charge. Equipment to be fitted within built limiter to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolt and once the concrete is set, fix the equipment on to it and cover nuts and bolt with the base plate cover, all complete as per direction and approval of Engineer-In-Charge regarding material shape of equipment colour on metal, seat and base cover plate and fixing of equipment etc. |
| 18 | Providing and fixing Exercising Barof size 1800x550x1700 mm make of Green Gym or Equivalent fabricated with main post of 140mm dia and 3.0 mm thick rest of the pipe are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tabular steel and hot dipped galvanized, and powder coated using Akzo nobel or equivalent of 80-120 micron thick. All welding joint of pipe are robotic welded with joint scalloped as necessary and dressed off removing sharp egde and burrs. Zinc primer paint to be applied at all welding points prior to finishing Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-In-Charge. Equipment to be fitted within built limiter to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolt and once the concrete is set, fix the equipment on to it and cover nuts and bolt with the base plate cover, all complete as per direction and approval of Engineer-In-Charge regarding material shape of equipment colour on metal, seat and base cover plate and fixing of equipment etc. |
| 19 | Providing and fixing Seated Chest Pressof size 1800x700x2000 mm make of Green Gym or Equivalent fabricated with main post of 140mm dia and 3.0 mm thick rest of the pipe are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tabular steel and hot dipped galvanized, and powder coated using Akzo nobel or equivalent of 80-120 micron thick. All welding joint of pipe are robotic welded with joint scalloped as necessary and dressed off removing sharp egde and burrs. Zinc primer paint to be applied at all welding points prior to finishing Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-In-Charge. Equipment to be fitted within built limiter to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolt and once the concrete is set, fix the equipment on to it and cover nuts and bolt with the base plate cover, all complete as per direction and approval of Engineer-In-Charge regarding material shape of equipment colour on metal, seat and base cover plate and fixing of equipment etc. |
| 20 | Providing and fixing Twisterof size 1700x1300x1300 mm make of Green Gym or Equivalent fabricated with main post of 140mm dia and 3.0 mm thick rest of the pipe are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tabular steel and hot dipped galvanized, and powder coated using Akzo nobel or equivalent of 80-120 micron thick. All welding joint of pipe are robotic welded with joint scalloped as necessary and dressed off removing sharp egde and burrs. Zinc primer paint to be applied at all welding points prior to finishing Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-In-Charge. Equipment to be fitted within built limiter to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolt and once the concrete is set, fix the equipment on to it and cover nuts and bolt with the base plate cover, all complete as per direction and approval of Engineer-In-Charge regarding material shape of equipment colour on metal, seat and base cover plate and fixing of equipment etc. |
| 21 | Providing and fixing MULTIACTIVITY PLAY SYSTEM(MAPS) Product Area 6.4m x 8.10m (20.9ftx26.5Ft). Modal and Design no.MAPS-07 Including supply of all material labour T&P etc all complete workincluding GST |
