|
| 1 | Providing and laying of Hot applied Thermoplastic compound 2.5mm thick including reflectoring glass beds @ 250 grms per Sqm. area thickness of 2.50mm is exclusive of surface applied glass beds as per IRC:35. The finished surface to be level, uniform and free from streaks and holes etc., complete (as per MORTH specification No. 803) |
| 2 | Providing and fixing reflective road studs of ‘category A’ Raised pavement markers made out of poly carbonate/methyl methecrylate/ABS moulded body conforming to ASTM D 788 and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity valuesconforming to ASTM D4280.The reflective raised pavement markers shall also confirm to the MORT&H circular No RW / NH. 33023/10/ 97-DO.III dt 11.06.97the height, width and length shall not be less than 15 mm, 90mm and 100 mm andwith minimum reflective area of 13 sq.cm. on each side and the slope to the baseshall be 35+/-5 degree. Each reflector shall have a CIL not less than values specified in table 2 of said MoRT&H circular.The strength of detachmentof the integrated cylinderical shanks,(of diameter not less than 19 +/- 2mm and height not less than 30 +/- 2mm ) from the body is to be a minimum value of 500kgf.Fixing will be by drilling holes on the road for the shanks to go inside,without nails and using epoxy resin based adhesive as per manufacturer\"s recommendation and complete as directed by the engineer.The marker shall support a load of 13635kg tested in accordance with ASTM D4280 and confirming to IRC 35 -2015 guide lines and MoRT&H Specification 804 etc., complete. |
| 3 | Providing and erecting of retro-reflectorised Cautionary, Mandatory and Informatory signs (with definition board) made out of High Intensity Prismatic grade sheeting confirming toType IV standards of IRC: 67-2012 and ASTMD 4956-09,specification and fixed over 2.00mm thick Aluminium sheet fixed over a back supporting frame of 25mm x 25mm x 3mm Mild steel angle and supported on a mild steel angle post 75mm x 75mm x 6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixedto the ground by means of properly designed foundation with M15 grade cement concrete 45cmx45cmx60cm size including cost and conveyance of all materials,equipment, machinery and labour with all leads and lift, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge.High Intensity retro reflectro sheet shall consist of minimum coefficient of Retro reflection as per Table 6.6 of IRC 67-2012.The retro refective sheeting shall be covered under seven year warrenty issued for field perfomance and a certified copy of three years out door exposer report shall be obtained as per IRC 67-2012 (as per MoRT&H Specification No:801) |
| 4 | (60 cm Circular board) |
| 5 | (90 cm Equilateral triangle) |
| 6 | Providing and erecting of retro-reflectorised Hazard marker traffic sign made out of high intensity Prismatic grade sheeting confirming to Type IV standards of IRC: 67-2012 and ASTMD 4956-09,specification and fixed over 2.00mm thick Aluminium sheet fixed over a back supporting frame of 25mm x 25mm x 3mm Mild steel angle and supported on a mild steel angle post 75mm x 75mm x 6mm and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmx45cmx60cm size including cost and conveyance of all materials,equipment,machinery and labour with all leads and lift, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge.High intensity Retro reflectro sheet shall consist of minimum coefficient of Retro reflection as per Table 6.6 of IRC 67-2012.The retro refective sheeting shall be covered under seven year warrenty issued for field perfomance and a certified copy of three years out door exposer report shall be obtained as per IRC 67-2012 (as per MoRT&H Specification No:801) 30cmx90 cm rectangular |
| 7 | Providing and erecting of retro-reflectorised Cautionary, Mandatory and Informatory signs (without definition board) made out of High Intensity Prismatic grade sheeting confirming Type IV standards of IRC: 67-2012 and ASTMD 4956-09,specification and fixed over 2.00mm thick Aluminium sheet fixed over a back supporting frame of 25mm x 25mm x 3mm Mild steel angle and supported on a mild steel angle post 75mm x 75mm x 6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmx45cmx60cm size including cost and conveyance of all materials,equipment,machinery and labour with all leads and lift, loading charges necessary for satisfactory completion of the work as directed by the engineer in charge.High Intensity retro reflectro sheet shall consist of minimum coefficient of Retro reflection as per Table 6.6 of IRC 67-2012.The retro refective sheeting shall be covered under seven year warrenty issued for field perfomance and a certified copy of three years out door exposer report shall be obtained as per IRC 67-2012 (as per MoRT&H Specification No:801) |
| 8 | (90 cm high octogan) |
| 9 | (80x60 cm rectangular Chevron Board |
| 10 | Providing and erecting of Direction and Place Identification Retro-reflectorised Sign made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67: 2012 and ASTM D 4956 -09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mmx25mmx3mm Mild Steel angle and supported on a mild steel angle post 75X75X6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmX45cmX60cm size including cost & conveyance of all materials, equipment, machinery&labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by theengineer in charge. High intensity Retro Reflectro sheet shall consist of minimumcoefficient of Retro-reflection as per Table 6.6 of IRC 67-2012. The retro- reflective sheeting shall be covered under 7 yearwarranty issued for field performance and a certifiedcopy of three years outdoor exposure report shall be obtained as per IRC 67:2012. (as per MORT&H Specification No.801) (for sign having area more than 0.9 sqm) Type-IV. |
| 11 | Providing fixing of Rigid median marker double sided made of polycarbonate for impact resistance and good weather ability. Polucarbonate used for molding the median marker shall have a minimum Izod impact strength value of 600 J/m at room temperature. The impact strength of the poly carbonate should not decrease to less than 70%of its initial value on beingsubjected to UV weathering as per ASTM G 155 for 1000 hoursorexposure to 2 years of natural weathering. The body of the median marker shall be in the form of an isosceles trapezoidal structure of length 15cm height and width of 10 x 10cm. The median marker shall have fluorescent yellow retro - reflective sheeting confirming to type XI specifications as per ASTM D 4956. Area of reflective sheeting should not less than 70 cm2. Edge of retro - reflective shall be concealed using a grill/mesh/similar mechanism to prevent vandalism and sheeting pilferage. The logo of the manufacturer shall be embossed and painted in contrasting colour on both side of median marker for distinct identification. |
| 12 | Providing and Fixing of Flexible Median Marker that are made of tough, high impact resistant, injectionmolded, thermoplastic body with property of flexibility to provide high durability. The dimension of Flexible Median Marker should not exceed 18.4 cm in height(including shank height),12.5 Cm in width.,0.65 cm in thickness and shank depth shall be 3.4 cm The body structure shall be rounded at all its corners and edges. The plastic used for molding the Flexible Median Marker should survive impact load of 5kg continuously for 750 times at room temperature. The logo of the manufacturer shall be embossed on either side of the body in the injection molding process. The Median Marker shall have flame like shaped body with, fluorescent yellow color retroreflective sheeting of size not less than 90 Cm square,with fully reflective micro prismatic cube corners as its retro-reflective elements as per IRC 67 2012 and ASTM D4956-09 type XI specifications reflectivity values. The retro-reflective sheeting shall be one orboth sides of the Flexible Median Marker and shall be edge protected with no exposed edges which will prevent edge lifting, vandalism, sheeting damage, |
| 13 | Proving and fixing Solar powered Traffic Blinkers of 30cm dia with Polycarbonate Dome 5mm Red of Led 150 Nos. iri each Red Blinkers Light - 1 No. with Red / White / Blue Led Blinkers Delineator Solar Panel :12v 50w Solar Panel — 1 No. 12v 18 AH Battery -1 No. with Box, Solar Circuit Controller Board Box.Straight Pole : MS Pole 3” dia 2.5mm thick 18 Feet height pole (1 No.) with 2 Feet under ground pole foundation, pole painting including transportation charges, installation charges etc., complete as per standard specification |
| 14 | Providing and erecting Single sided Double Guard Metal Beam Crash Barrier System 1.70m high,comprising of 3mm thick wall “W” beams posts and spacer channels shall be made by cold roll forming using HR conform to IS 5986 Fe 410/360 and dip galvanized having Zinc Mass of 550gms/ sqm, minimum 950mm above road/ ground level fixed on ISMC series channel vertical post 150x75x5mm spaced 2m center to center 312mm x 83mm flange width x 3mm thick, 4318mm long post directly embedded in the concrete (M15) pit size 350x350x800mm for a depth of 750mm below ground. All fixing bolts and nuts hot dip galvanized conforming to IS:1367 clause 4.60 all complete as per Technical Specification and as directed by the Engineer- in- charge |
| 15 | Providing and fixing of Digitally Printed Retro Reflectorized Sign Board using UV Inkjet Printer made out of cube corner micro prismatic grade sheeting of Type-XI standards of IRC 67-2012 and ASTM D 4956 – 09 specification, Digitally Printed using UV Inkjet Printer (UVIJ) for traffic colour, images/ logos/ text and laminated with clear electrocuttable film and applied to properly prepared sign substrates, fixed over 2mm Aluminium sheet with back supporting frame of 50x50x6mm Mild Steel ‘L’ angle and supported on a 150NB (Nominal Bore) pipe with 4.50mm thick with an overall height from top of the board to foundation. The sign board should be of 2.10m clear height from the ground level to the bottom of the sign board and 1.10m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete of size 450x450x1100mm including cost and conveyance of all materials, equipment, machineries to worksite, including all labour charges for fixing the gantry in position with all leads and lifts, loading charges and necessary for satisfactory completion of the work as directed by the engineer-in-charge etc., complete. The Micro prismatic sheeting should have minimum 70% co-efficient of Retro-reflection values as per table 6.90 of IRC 67-2012. The retroreflective sheeting shall be covered under 10 Years warranty issued for field performance and a certified copy of 3 years outdoor exposure report shall be obtained as per IRC 67-2012. The warranty shall be inclusive of digitally printed images/ logos/ test/ legends and their bonding to the retro-reflective sheeting (as per MoRT&H specification no.801) of Size – 3.64m x 2.42m |
| 16 | Supplying and installation of delineators (road way indicators, hazard markers and object markers), 80-100 cm high above ground level, painted at alternatively black and white in 15 cm wide strips, fitted with 80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground and conforming to IRC-79 etc., complete (as per MoRT&H specification No. 806) |
| 17 | Calculation of SubTotal, GST and Total Amount carried out by system automatically |
| 18 | Basic cost of value put to tender as per estimate |
| 19 | Add GST at 18% |
| 20 | Total Value put to Tender |
| 21 | Difference in Value |
| 22 | Bidder quoted value |
| 23 | Add GST at 18% of Final quoted Value |
| 24 | Total Value of Contract Including 18% of GST |
| 25 | Basic cost of value put to tender as per Estimate |
| 26 | Quoted Rate in Figures (Total Value of Contract Including 18% of GST ) |
