|
| 1 | Providing and fixing \"Air Walker\" with below specifications: 1. Dimensions (LxWxH): 1100 x 450 x 1300mm2. Fabricated with main post of NB 100mm (G.1.) C Class Pipe of approved make3. U shaped main frame of NB 80mm (G.1.) C Class Pipe, Leg Support frame of NB 50mm (0.1) C Class Pipe4. Handy frame pipes of NB 32mm (G.1.) C ClassNB stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres)5. All Pipes are powder coated with 80–120-micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs7. Zinc primer paint is applied at all the welding points prior to finishing.8. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured.9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.11. The equipment are fitted with inbuilt limiters to prevent unwanted movements.12. The equipment is fixed on ground with concrete of minimum strength M-25 and I shaped welded bolts of 18mm thickness.13. 14. High tensile steel with galvanized nut bolts is used for assembly.Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.15. Equipment made to G5 Mark, EN16630, DIN 79000 & 150 14001 International standard for outdoor fitness equipment16. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. |
| 2 | Providing and fixing double\" Sit-Up Station\" with below specifications: 1. Dimensions (LxWxH): 1600 x 1150 x 650mm2. Fabricated with main frame of NB 100mm (G.I.) \"C\" Class Pipe of approved make.3. Main frame of NB 25mm (G.I.) \"C\" Class Pipe.4. Leg support of NB 65mm (G.I.) \"C\" Class Pipe \"NB\" stands for Nominal Bore i.e., Internal Diameter of pipe in millimetre’s) 5. Fixed on its top is back support made of perforated MS sheet of 2mm thickness.6. All pipes are powder coated using Akzo Nobel or equivalent Paint of 80-120 micron thick.7. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.8. Zinc primer paint is applied at all welding points prior to finishing.9. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured.10. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 11. Once the concrete is set, the equipment is fixed on to it.12. High tensile steel with galvanized nut bolts are used for assembly.13. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.14. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. |
| 3 | Providing and fixing \"Air Swing\" in pair with below specifications:1. Dimensions (LxWxH): 1150 x 900 x 1250 mm2. Fabricated with main post of NB 100mm (G.I.) \"C\" Class Pipe of approved make. 3. Leg Support frame of NB 50mm (G.I.) \"C\" Class Pipe. 4. Handle support frame of NB 32mm (G.I.) \"C\" Class Pipe. (\"NB\" stands for Nominal Bore i.e., Internal Diameter of pipe in millimetre’s)5. All Pipes are powder coated with 80–120-micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Handle bars are provided with high end quality rubber grips.9. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. 10. Foothold made of MS Sheet Metal with rounded edges to prevent impact and injury.11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.15. High tensile steel with galvanized nut bolts are used for assembly.16. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. |
| 4 | Providing and fixing \"Horse Rider Station\" with below specifications:1. Dimensions (LxWxH): 1000 x 600 x 1100 mm2. Fabricated with main post of NB 100mm (G.I.) \"C\" Class Pipe of approved make.3. Main frame of NB 65mm (G.I.) \"C\" Class Pipe. 4. Handle support frame of NB 50mm (G.I.) \"C\" Class Pipe and other pipes of 4 NB 32mm & NB 25mm (G.I.) \"C\" Class Pipe. (\"NB\" stands for Nominal Bore i.e., Internal Diameter of pipe in millimetre’s)5. All Pipes are powder coated with 80–120-micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing.8. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured.9. Foothold made of NB 32mm (G.I.) \"C\" Class Pipe. 10. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmentally friendly.11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly.16. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. |
| 5 | Providing and fixing \"Leg Press\" in a pair with below specifications:1. Dimensions (LxWxH): 2000 x 600 x 1800 mm2.Fabricated with main post of NB 100mm (G.I.) \"C\" Class Pipe of approved make.3. Seat Main frame of NB 50mm (G.I.) \"C\" Class Pipe and Pipe connecting main post to seat main frame of NB 65mm (G.I.) \"C\" Class Pipe. (\"NB\" stands for Nominal Bore i.e., Internal Diameter of pipe in millimetre’s)4. All Pipes are powder coated with 80–120-micron thick AkzoNobel or equivalent Paints. 5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.6. Zinc primer paint is applied at all the welding points prior to finishing.7. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured.8. Foothold made of NB 50mm (G.I.) \"C\" Class Pipe.9. Seats made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmentally friendly. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.11. The equipment are fitted with inbuilt limiters to prevent unwanted movements.12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.14. High tensile steel with galvanized nut bolts are used for assembly.15. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.16. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. |
| 6 | Providing and fixing \"Pull Chair\" in a pair with below specifications:1. Dimensions (LxWxH): 2400 x 800 x 2000 mm2. Fabricated with main post of NB 100mm (G.L.) C Class Pipe of approved make. 3. Seat main frame of NB 50mm (G.L.) C Class Pipe, Pipe connecting main post with handle frame of NB 65mm (GL) \"C\" Class Pipe4. Handle frame of NB 32mm (G.L.) C Class Pipe. (\"NB\" stands for Nominal Bore le., Internal Diameter of pipe in millimetre’s)5. All Pipes are powder coated with 80–120-micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing.8. Handle bars are provided with high end quality rubber grips.9. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured.10. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmentally friendly.11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.12. The equipment are fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is fixed on ground with concrete of minimum strength M-25 and I shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.15. High tensile steel with galvanized nut bolts are used for assembly.16. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. |
| 7 | Providing and fixing \"Seated Chest Press\" in a pair with below specifications:1. Dimensions (LxWxH): 1800 x 700 x 2000 mm2. Fabricated with main post of NB 100mm (G.I.) \"C\" Class Pipe of approved make. 3. Seat Main frame of NB 50mm (G.I.) \"C\" Class Pipe.4. Handle frame of NB 32mm and NB 25mm (G.I.) \"C\" Class Pipe.(\"NB\" stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimetre’s).5. All Pipes are powder coated with 80–120-micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing.8. Handle bars are provided with high end quality rubber grips. 9.Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured.10. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant andenvironmentally friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.15. High tensile steel with galvanized nut bolts are used for assembly.16. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. |
| 8 | Providing and fixing \"Arm Wheel\" in a pair with below specifications:1. Dimensions (LxWxH): 850 x 800 x 1800 mm2. Fabricated with main post of NB 100mm (G.I.) \"C\" Class Pipe of approved make. 3. Wheel frame of NB 32mm with connecting spokes of NB 25mm, Pipe connecting main pilar with wheel frame of NB 50mm. All pipes must be (G.I.) \"C\" Class Pipes. (\"NB\" stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimetre’s). 4. All Pipes are powder coated with 80–120-micron thick AkzoNobel or equivalent Paints.5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.6. Zinc primer paint is applied at all the welding points prior to finishing.7. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured.8. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.9. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.10. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 11.High tensile steel with galvanized nut bolts are used for assembly.12. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. 13. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. |
| 9 | Providing and fixing \"Elliptical exerciser\" with below specifications: 1. Dimensions (LxWxH): 1200 x 550 x 1600 mm2. Fabricated with main post of NB 100mm (G.I.) \"C\" Class Pipe of approved make.3. Main frame of NB 80mm (G.I.) \"C\" Class Pipe.4. Handle frame of N8 32mm and NB 25mm (G.I.) \"C\" Class Pipe. (\"NB\" stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimetre’s).5. All Pipes are powder coated with 80–120-micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.11. The equipment is fixed on ground with concrete of minimum strength M-25 and I shaped welded bolts of 18mm thickness.12. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.13. High tensile steel with galvanized nut bolts are used for assembly.14. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. 15. Self-Explanatory stainless-steel label fixed on equipment for ease of use.16. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury, including maintenance cost for 2 years. |
| 10 | Providing and fixing \"Double Cross Walker \"with below specifications:1. Dimensions (LxWxH): 1600 x 600 x 1600 mm2. Fabricated with main post of NB 100mm (G.I.) \"C\" Class Pipe of approved make.3. Handle main frame of NB 50mm and other connecting pipes of NB 32mm and NB 25mm (G.I.) \"C\" Class Pipe. (\"NB\" stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimetre’s).4. Foot support frame of 96 x 46 x 3mm MS rectangular pipe. 5. All Pipes are powder coated with 80–120-micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. 9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury.10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with concrete of minimum strength M-25 and shaped welded bolts of 18mm thickness.13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.14. High tensile steel with galvanized nut bolts are used for assembly.15. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.16. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. |
| 11 | Providing and fixing \"Triple Twister\" with below specifications:1. Dimensions (LxWxH): 1300 x 1300 x 1650 mm. 2. Fabricated with main post of NB 100mm (G.I.) \"C\" Class Pipe of approved make.3. Handle Main frame of NB 32mm (G.I.) \"C\" Class Pipe.4. Handle frame spokes of NB 25mm (G.I.) \"C\" Class Pipe. (\"NB\" stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimetre’s). 5. Foothold plate of made of MS Sheet Metal of 3mm thickness.6. All Pipes are powder coated with 80–120-micron thick AkzoNobel or equivalent Paints.7. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.8. Zinc primer paint is applied at all the welding points prior to finishing.9. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.10. The equipment is fixed on ground with concrete of minimum strength M-25 and shaped welded bolts of 18mm thickness.11. Once the concrete is set, the equipment is fixed on to it.12. High tensile steel with galvanized nut bolts are used for assembly.13. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. 14. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. |
| 12 | Providing and fixing \"Rowing Machine\" with below specifications:1. Dimensions (LxWxH): 1250 x 800 x 1150 mm2. Fabricated with main post of NB 100mm (G.I.) \"C\" Class Pipe of approved make.3. Main frame of NB 65mm (G.I.) \"C\" Class Pipe. 4. Handle support frame of NB 25mm (G.I.) \"C\" Class Pipe. (\"NB\" stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimetre’s).5. All Pipes are powder coated with 80–120-micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured.9. Foothold made of NB 50mm (G.I.) \"C\" Class Pipe.10. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmentally friendly.11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.15. High tensile steel with galvanized nut bolts are used for assembly.16. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. |
| 13 | Providing and fixing \"Stair Stepper\" with below specifications:1. Dimensions (LxWxH): 1100 x 800 x 1400 mm2. Fabricated with main post of NB 100mm (G.I.) \"C\" Class Pipe of approved make (\"NB\" stands for Nominal Bore i.e., Internal Diameter of pipe in millimetre’s) 3. Twister main frame of NB 32mm (G.I.) \"C\" Class Pipe and Handle frame of NB 32mm (G.I.) \"C\" Class Pipe. Twister Foothold plate of made of MS Sheet Metal of 3mm thickness.4. Stepper main frame of MS pipe 96 x 46mm and Handle frame of NB 32mm & 25mm (G.I.) \"C\" Class Pipe.5. All Pipes are powder coated with 80–120-micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury.9. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 10. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.11. Once the concrete is set, the equipment is fixed on to it. 12. High tensile steel with galvanized nut bolts are used for assembly.13. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.14. Self-Explanatory stainless-steel label fixed on equipment for ease of use. 15. The equipment are fitted with inbuilt limiters to prevent unwanted movements.16. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured including maintenance cost for 2 years. |
| 14 | Providing and fixing \"Exercising Bar” with below specifications:1. Dimensions (LxWxH): 1600 x 1150 x 650mm.2. Fabricated with main frame of NB 100mm (G.I.) \"C\" Class Pipe of approved make.3. Main frame of NB 25mm (G.I.) \"C\" Class Pipe.4. Leg support of NB 65mm (G.I.) \"C\" Class Pipe (\"NB\" stands for Nominal Bore i.e., Internal Diameter of pipe in millimetre’s) 5. Fixed on its top is back support made of perforated MS sheet of 2mm thickness.6. All pipes are powder coated using Akzo Nobel or equivalent Paint of 80-120 micron thick. 7. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.8. Zinc primer paint is applied at all welding points prior to finishing.9. Base plate cover made of virgin LLDPE plastic by rotational moulding with 4.00mm thickness, UV resistant and coloured.10. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.11. Once the concrete is set, the equipment is fixed on to it.12. High tensile steel with galvanized nut bolts are used for assembly.13. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.14. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years. |
| 15 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer -in - charge.(a) Nominal concrete 1:3:6 or richer mix (including equivalent design mix).i/c modified GST factor (2368.50x0.973) |
| 16 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. i/c modified GST factor (256.80x0.973) |
| 17 | Deduct for taking away the Old gym equipment without dismembering i/c dismantling charges and removing the dismantled old gym equipment\"s from the site as per the direction of Engineer-in-charge.Air Swing |
| 18 | Air Walker |
| 19 | Horse Rider Station |
| 20 | Arm Wheel |
| 21 | Double Cross Walker |
| 22 | Elliptical exerciser |
| 23 | Exercising Bar |
| 24 | Leg Press |
| 25 | Pull Chair |
| 26 | Rowing Machine |
| 27 | Seated Chest Press |
| 28 | Sit Up Station |
| 29 | Stair Stepper |
| 30 | Triple Twister |
| 31 | SCHEDULE-\"B\"For 3rd year all item of Schedule \"A\" except item No. 15 .00to17.14on Rs. 2882922/- @ 2.00 % |
| 32 | For 4th year all item of Schedule \"A\" except item No. 15 .00to17.14 on Rs. 2882922/- @ 3.00% |
| 33 | For 5th year all item of Schedule \"A\" except item No. 15 .00to17.14 on Rs. 2882922/- @ 4.00% |
