Tender For Construction Of Park In W.No. 06 Ghuggar Khildu Mc Palampur, palampur-Himachal Pradesh

Tender For Construction Of Park In W.No. 06 Ghuggar Khildu Mc Palampur; 1 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) 2 Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. Ordinary soil 3 Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade 4 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 5 Providing and Fixing Cast iron ornametal railing of size complete as drawing and design as per the instruction of Engineer-in-charge. 6 Stone soling properly handpacked filling interstices with Kharanja stone and consolidating with power road roller to the requested gradient and comber including spreading watering and rolling of binding materials moorum or earth etc. complete as per HP.PWD specification. 100 mm spread thickness (finished work including materials and labour) 7 Providing and Laying concrete for plain/reinforced concrete in open foundations complete as per drawing and technical specification clauses 802, 803, 1202 and 1203 1:4:8 8 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. 9 Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 P.C.C. grade M 20 Nominal mix (1:2:4) 10 Supplying of TRIPPLE TWISTER having specification of Dimensions: (LX W X H) = 1430mm X 1280mm X 1440 mm.Made of 3mm thick GI pipe. Gauge – 8 Ms Main frame- Made from114 mm OD A Class G.l. pipe. Foundation plate -M.S. round plate of250 mm & 8mm thick. Main frame bottoms protective cover - decent design seamless deep draw G.l. sheet metal cap. Bottom protective cover made in G.I Sheet top size 153X153mm and bottom size 239X239X90mm height with 03mm wall thickness. Shoulder ring pipe- D33 mm OD A Class G.I Pipe. Shoulder ring pipe support - 25 mm OD A Class G.I Pipe. Handle knob -Made up of stainless-steel ball shaped OD 70mm is fixed on shoulder ring pipe for rotational purpose. Top Closing caps- dome shape made by G.I material... Closing cap - PP/NYLON/HDPE materialFoundation stool: Made from main pipe 088 mm OD M.S pipe and top support of M.S. round plate of250 mm & 8mm thickness is welded at top. Square tube of 30x30x2 mm is use for to support center pipe. Foundation stool is embedded in C.C. stock below ground level. Bearing - Use is 6005 permanent lubricated reputed brands.Pin- 25 mm M.S. Foundation plate -M.S. round plate of250 mm & 8mm thick.Bearing bushes - 60 mm OD seamless pipe. circlips - A 24 circlips are used for assembly. Coating - best quality of powder coating 80-100 micron. .And as per direction of Engineer in charge 11 Supplying of BODY SHAPER having specification of Dimensions: (LX W X H) = 1370mm X 890mm X 1610 mm. Made of 3mm thick GI pipe. Gauge – 8 Ms Main frame- Made from114 mm OD A Class G.l. pipe. Foundation plate -M.S. round plate of250 mm & 8mm thick. Main frame bottoms protective cover - decent design seamless deep draw G.l. sheet metal cap. Bottom protective cover made in G.I Sheet top size 153X153mm and bottom size 239X239X90mm height with 03mm wall thickness. Shoulder ring pipe- D33 mm OD A Class G.I Pipe.Shoulder ring pipe support - 25 mm OD A Class G.I Pipe.Handle knob -Made up of stainless-steel ball shaped OD 70mm is fixed on shoulder ring pipe for rotational purpose. Top Closing caps- dome shape made by G.I material...Closing cap - PP/NYLON/HDPE material. Foundation stool: Made from main pipe 088 mm OD M.S pipe and top support of M.S. round plate of250 mm & 8mm thickness is welded at top.Square tube of 30x30x2 mm is use for to support center pipe. Foundation stool is embedded in C.C. stock below ground level. Bearing - Use is 6005 permanent lubricated reputed brands.Pin- 25 mm M.S. Foundation plate -M.S. round plate of250 mm &8mm thick.Bearing bushes - 60 mm OD seamless pipe. circlips - A 24 circlips are used for assembly. Coating - best quality of powder coating 80-100 micron.And as per direction of Engineer in Charge. 12 Supplying of AIR WALKER having specification of Dimensions: (LX W X H) = 14005mm X 540mm X 1495 mm.Made of 3mm thick GI pipe. Gauge – 8 Ms Main frame- Made from114 mm OD A Class G.l. pipe. Foundation plate -M.S. round plate of250 mm & 8mm thick.Main frame bottoms protective cover - decent design seamless deep draw G.l. sheet metal cap.Bottom protective cover made in G.I Sheet top size 153X153mm and bottom size 239X239X90mm height with 03mm wall thickness. Shoulder ring pipe- D33 mm OD A Class G.I Pipe.Shoulder ring pipe support - 25 mm OD A Class G.I Pipe. Handle knob -Made up of stainless-steel ball shaped OD 70mm is fixed on shoulder ring pipe for rotational purpose. Top Closing caps- dome shape made by G.I material...Closing cap - PP/NYLON/HDPE material.Foundation stool: Made from main pipe 088 mm OD M.S pipe and top support of M.S. round plate of250 mm & 8mm thickness is welded at top.Square tube of 30x30x2 mm is use for to support center pipe.Foundation stool is embedded in C.C. stock below ground level.Bearing - Use is 6005 permanent lubricated reputed brands.Pin- 25 mm M.S. Foundation plate -M.S. round plate of250 mm & 8mm thick.Bearing bushes - 60 mm OD seamless pipe. circlips - A 24 circlips are used for assembly.Coating - best quality of powder coating 80-100 micron. And as per direction ofEngineer in Charge 13 Supplying of CHEST AND SHOULDER having specification of Dimensions: (LX W X H) = 2560mm X 666mm X 1810 mm. Made of 3mm thick GI pipe.Gauge – 8 Ms Main frame- Made from114 mm OD A Class G.l. pipe.Foundation plate -M.S. round plate of250 mm & 8mm thick.Main frame bottoms protective cover - decent design seamless deep draw G.l. sheet metal cap. Bottom protective cover made in G.I Sheet top size 153X153mm and bottom size 239X239X90mm height with 03mm wall thickness. Shoulder ring pipe- D33 mm OD A Class G.I Pipe.Shoulder ring pipe support - 25 mm OD A Class G.I Pipe.Handle knob -Made up oftainless-steel ball shaped OD 70mm is fixed on shoulder ring pipe for rotational purpose. Top Closing caps- dome shape made by G.I material... Closing cap - PP/NYLON/HDPE material. Foundation stool: Made from main pipe 088 mm OD M.S pipe and top support of M.S. round plate of250 mm & 8mm thickness is welded at top.Square tube of 30x30x2 mm is use for to support center pipe.Foundation stool is embedded in C.C. stock below ground level.Bearing - Use is 6005 permanent lubricated reputed brands. Pin- 25 mm M.S. Foundation plate -M.S. round plate of250 mm & 8mm thick. Bearing bushes - 60 mm OD seamless pipe. circlips - A 24 circlips are used for assembly. Coating - best quality of powder coating 80-100 micron.And as per direction of Engineer in Charge.

INR 590 /-

INR 20000.0 /-

INR 9.83 Lakhs /-