|
| 1 | SITC ofMNRE approved & confirming to IS:12933 P-1,2,3 & 5 Flat Plate Collector type solar hot water system havingcollector withZincalum sheet outer body ,Glass - line / Titanium Enamel coated Inner tank with Metal rust proof PUF insulated Body includingelectrical back up, Thermostat, Powder coated / Hot dipped galvanized MS standfor Collector & Tank etc. as required. of following capacity complete in all respect. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . |
| 2 | 500 litre/ day |
| 3 | SITC of Radial / mixed flow ISI marked water and anti-corrosive liquid filled submersible motor pump setssuitable for 100/150mm dia borewell.The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034 : 2018 and IS: 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008,& IS12615:2011with required accessories including making connection suitable for Bore well. The job includes labour part of lowering ofriser pipe G.I./H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to Starter. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. OEM shall have submitNABL / CPRI / ERDA accrediatedlab type test certificate before execution. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . |
| 4 | 150 mm diameter Submersible pump shall havefollowing HP Rating, phase, Head range, Discharge range respectively. |
| 5 | 5.0 HP, 3-Ø, (68 - 102)Mtr, (225-85) LPM |
| 6 | Providing & Fixing of HDPE pipe Confirming to IS:4984:2021for water supply suitable for submersible & jet pump with required fittings ie socket, elbows, tee etc. complete in all respect. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . |
| 7 | for vertical installation |
| 8 | 50 mm OD6 kg / cm2 |
| 9 | Providing & Laying of Polypropylene rope Confirming to IS:5175 for submersible pump of following sizes. complete in all respect. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . |
| 10 | 12mm (suitable up to 50 mm OD pipe) |
| 11 | P/Laying ISI marked P.V.C. insulated submersible cable confirming to(IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen freefor less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,existing pipe / open trench / Cable tray / on surface including making connection etc. as required. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSR |
| 12 | 4.0 Sq.mm 3 core flat / Round |
| 13 | SITC of ContactorOEM Fabricated DOL/Star-Delta Starter panel with switchgear selection as per Type-2 Cordinatiom Chart andmade out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFFpush buttons,ammeter, voltmeter, indicating lamps etc.suitable for following rating motors complete in all respect. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR . |
| 14 | For Three phase Submersible / Mono block pump |
| 15 | 3.0 HP to 5.0 HP ( Star / Delta starter ) |
| 16 | CIVIL BSR 2022 |
| 17 | P & F G.I. pipes (Internal Work) with G.I. Fittings excluding |
| 18 | union (IS:1239 Mark) & MS clamps including cutting and |
| 19 | making good the walls and floors: |
| 20 | (a) Exposed on wall |
| 21 | 20mm dia nominal bore \"B\" Class |
| 22 | 25mm dia nominal bore \"B\" Class |
| 23 | P & F Bib Cock (IS : 8931 Mark), Superior quality of |
| 24 | approved make: |
| 25 | C.P. Brass bib cock,15mm nominal bore. |
| 26 | P & F Full-way Valve (IS:778 Mark) or wheel valve of |
| 27 | approved make : |
| 28 | Gun-metal 20mm nominal bore. |
| 29 | Gun-metal 25mm nominal bore. |
| 30 | P & F PVC Storage Tank ISI Marked (IS : 12701) indicating |
| 31 | the BIS license No), of approved make with cover, 25mm dia |
| 32 | 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe |
| 33 | with plug & socket, including making connection etc., |
| 34 | complete of approved design: |
| 35 | 500 litres capacity. |
| 36 | Providing and fixing Polyethylene - Aluminium -Polyethylene |
| 37 | (PE-AL-PE) Composite Pressure Pipes as per 15450 : 2004 |
| 38 | U.V. stablised with carbon black having thermal stabillity for |
| 39 | hot and cold water supply, capable to withstand temperature |
| 40 | upto 80ºC including all special fittings of composite material |
| 41 | (engineering plastic blend and brass inserts wherever required) |
| 42 | e.g. elbows, tees, reducers, couplers connectors etc.with |
| 43 | clamps at 1.00 metre spacing.This include the cost of cutting |
| 44 | chases and including testing of joints complete as per direction |
| 45 | of Engineer In charge |
| 46 | Internal work - Exposed on Wall |
| 47 | 1620 (20mm OD) pipe |
| 48 | 2025 (25mm OD) pipe |
| 49 | P & F Full-way Valve (IS:778 Mark) or wheel valve ofapproved make : |
| 50 | Gun-metal 15mm nominal bore. |
| 51 | (-do-) 50mm nominal bore. |
| 52 | Supply & fixing G.I. Union ISI marked in G.I. pipe line as |
| 53 | required complete in all respect of size : |
| 54 | 20mm dia nominal bore |
| 55 | 25mm dia nominal bore |
| 56 | Making connection of G.I. distribution branch with G.I. main |
| 57 | including all fittin |
| 58 | Upto 25mm dia |
| 59 | Providing and fixing welded mesh/expanded metal mesh in |
| 60 | frame work, flat iron beading 20x3mm including top cross laps |
| 61 | inside and out sides welding, iron bolts, crews, clips etc. |
| 62 | complete (excluding frame work) of size. |
| 63 | Welded mesh 25 mmx 25 mm x 2.1 mm |
| 64 | P & F Ball Cock (IS :1703 Mark) with Rod & P.V.C. Ball |
| 65 | complete : |
| 66 | Brass wt. Not less than 300 gm,15mm. |
