|
| 1 | M &L for pressure washing and cleaning thoroughly the bottom floor and inside walls of 700000 gallons capacity swimming pool after draining out of water including cleaning of joints of tiles of the pool by suitable mechanical means using mild hydrochloric acid for fungus/algae free surfaces including removing out all dirt and foreign matters if any from the pool to a distance not exceeding 50m complete to the satisfaction of the Engineer-in-Charge all as specified and directed.Notes :-(a) Size of the Swimming Pool is 50m length x 25m width and depth varying from 1.2m to 3m (Approx).(b) Draining of water from the Swimming Pool shall be made by the department.(c) Draining of water, pump & motor provided by contractor for suitable capacity. |
| 2 | M&L for pressure washing and cleaning thoroughly the bottom and inside walls of balancing tank of the swimming pool after draining out of water by suitable mechanical means using bleaching powder including removing of sludge/slurry/foreign matters if any from the tank to a distance not exceeding 50m complete to the satisfaction of the Engineer-in-Charge all as specified and directed.Notes :-(a) Size of the Balancing tank is 3.6m length x 2.9m width and depth 4m (Approx)(b) Draining of water from the Balancing tank shall be made by the department.(c) Draining of water, pump & motor provided by contractor for suitable capacity. |
| 3 | Cleaning of swimming pool (2 / 3 days in a week as per requirement ) including by providing of minimum 4 Nos labour for operating of suction sweeper & submersible pool cleaner and mannual cleaning by using brushes, sweeps etc to the floor sides of walls, over flow water channel of swimming pool surrounding area removing all floated materials/insects from pool water and removing all foreign materials muds etc from pool area to outside of the pool not less than 50 mtr as directed at site Engr-in-charge.Note :- (i) Daily maintenance of swimming pool is to be carriied out as per operating time schedule of the swimming pool, i.e. wef 9:30 AM to 3:00 PM.and all T&P are the responsibilitry of the contractor(ii) Surrounding areas of the pool including plant room shall be cleaned after 3:00 PM & upto 5:30 PM. |
| 4 | M&L for Filter media refilling of Quartz sand sewed as per the standards and details are as followa. Fine sand 16X32 mesh of 450 mm depth = 2X7.0MT |
| 5 | Labour charges washing of filter media (pebbles) and re filling of pebbles and new media and complete to the satisfaction of the Engineer-in-charge all as specified and directed. |
| 6 | M&L for inside painting of filters two coat of red oxide and two coats of epoxy and complete to the satisfaction of the Engineer-in-charge all as specified and directed. |
| 7 | Supply in replacementPVC flexible suction and delivery hoses, ISI marked incorporating a rigid PVC priral as an integral part of the soft PVC balls green ribbed colour of 40 mm dia, working pressure @ 6 kg/Sqcm complete all as specified and directed. |
| 8 | Supply in replacement only PVC flexible suction and delivery hoses, ISI marked incorporating a rigid PVC spiral as an integral part of the soft PVC wallgreen ribbed colour of 50 mm dia, working pressure @ 6 kg/Sqcm complete all as specified and directed. |
| 9 | Supply in cosumptionliquid amonia in 450 ml PVC bottle complete all as specified and directed.Make :-Pearl Filler/RMCO/Mizag. |
| 10 | Supplyin cosumption free chlorine testing kit paper strips (Colome metric TMG) for detection levels (0.05, 0.1, 0.4, 0.6, 0.8, 1.2, 1.5, 2.0, 4.0, 6.0 ppm (Mgle) test time 40 seconds having each bottle of 50 test strips complete all as specified and directed. |
| 11 | Supplyin cosumption Tri chloro isocyanuric acid(TCCA-90)in white granular form for disinfectant for swimming pool of supar quality contains chlorine 90 % duly packed in 50 kg drum100% solvable in water, having molecular weight 23.44 and appearance in white PH value 1% solution - 2.7 to 3.3 and moisture level 0.5% complete all as specified and directed. |
| 12 | Supplyin cosumption nonferric alum best quality, ISI marked suitable for using at water treatment plant for drinking purpose complete all as specified and as directed. |
| 13 | Supplyin cosumption bleaching powder of 30% chlorine available, ISI marked Grade-IQUALITY CONFORMING TO is 673 PACKED IN FACTORY SEALED POLY PACK AND DELIVERED AT AGE E/M II (U) store yard complete all as specified and as directed. |
| 14 | Supplyin cosumption Hydrochloric acid industrial grade complete all as specified and directed. |
| 15 | Supplyin cosumption soda ash confirming to IS complete all as specified and directed. |
| 16 | Supplyin consumption copper sulphate crystal, ISI marked to maintain the H2O standards complete all as specified and directed.Notes for item No 9 to 16 :-(i) Contractor shall supply material as per monthly requirement basis in bags/containers as and when directed at various installation of AGE E/M No-II.(ii)The quoted rateis deemed to be included complete labour and transportation for the materials at various installations of AGE E/M No II with out any extra cost.(iii) Supplier must provide alongwith materials, \"certificate of compliance\"/\"Test certificate\" in original indicating Batch No, date of manufacturing and quantity supplied. |
| 17 | Supply and testing water hardness test kit digital type complete all as specified and directed. |
| 18 | Supply in replacement nylon rope of size 1\" (Inch) dia suitable for suction sweeper complete all as specified and directed. |
| 19 | M&L for repairs/replacement of suction sweeper i.e wheel, leather patti, wheel hook, nut, bolt, washer and brushes of suitable size complete all as specified and directed |
| 20 | Supply in replacement leaf net, deep bag net made in polypropylene and white polyester netting including butterfly connection for swimming pool complete all as specified and directed. |
| 21 | Supply in replacement surface net made in polypropylene and white polyester netting butterfly connection for swimming pool complete all as specified and directed. |
| 22 | Supply in replacement extension able handles for cleaning attachments in anodized aluminium which can be adapted to the entire range of cleaning equipment, brushes, leaf skimmers and scoops, 7.5 mts, long for swimming pool complete all as specified and directed. |
| 23 | Supply in replacement transparent blue plastic vacuum hose 2\" (Inch) dia, 30 mtrs long medium gradeincluding hose cuffs for connection to suction inlets complete all as specified and directed. |
| 24 | Supply in replacement of curved brushes made in polypropylene for pool basins and scum liners complete all as specified and directed. |
| 25 | Supply in replacement straight brushes made in polypropylene for pool basins and scum liners complete all as specified and directed. |
| 26 | Supply in replacement Suction sweeper wheels as per sample of swimming pool complete all as specified and directed. |
| 27 | Arresting leakages from pumps of motor capacity 05 HP to 25 HP by replacing gasket, nutbolts, gland packing etc as required complete all as directed Note: Rate quoted by the contractor inclusive of all items as requiree to arrest the leakages from pumps |
| 28 | Serviceaning / periodical checking of Starter panel board suitable for 15 HP to 40 HP Motor by replacing all unserviceable parts , checking for any kind of loose contact , identification of fault etc complete all as specified and directed . Note : All spare to be replaced and measured under relevant items. |
| 29 | Serviceaning / periodical checking of Starter panel board suitable for 5 HP to 10 HP Motor by replacing all unserviceable parts , checking for any kind of loose contact , identification of fault etc complete all as specified and directed . Note : All spare to be replaced and measured under relevant items. |
| 30 | M&L for Disconnecting the suction and delivery pipe line and electric connections of centrifugal Monoblockpump set 7.5 HP to 25 HP capacity and removing it from its position carefully and transporting the same to the work shop and refixing the same in its original position after carryout the repairs and connecting back the water and electric connections including testing and commissioning complete all as specified and directed. |
| 31 | M&L for Disconnecting the suction and delivery pipe line and electric connections of centrifugal Monoblockpump set 1 HP to 5 HP capacity and removing it from its position carefully and transporting the same to the work shop and refixing the same in its original position after carryout the repairs and connecting back the water and electric connections including testing and commissioning complete all as specified and directed. |
| 32 | M&L in repair of centrifugal pump set of 1 to 5 HP capacity to achieve the water discharge as per manufacturer recommendation including replacement of worn out unserviceable parts complete all as specified and directed.Notes :-(i) Expendable stores like cotton waste/cleaning materials, lubricants, gland packing, metal filling, matching and transportation to and from site to work shop are deemed to be included in unit rate quoted.(ii) Labour against this item for replacement of spares (supply only items) shall be deemed to be included in the rate quoted.(iii) Spare parts like SS sleeves, impeller, stage casing etc shall be measured and paid separately under relevant item of Sch \"A\". |
| 33 | M&L in repair of centrifugal pump set of 7.5to 25 HP capacity to achieve the water discharge as per manufacturer recommendation including replacement of worn out unserviceable parts complete all as specified and directed.Notes :-(i) Expendable stores like cotton waste/cleaning materials, lubricants, gland packing, metal filling, matching and transportation to and from site to work shop are deemed to be included in unit rate quoted.(ii) Labour against this item for replacement of spares (supply only items) shall be deemed to be included in the rate quoted.(iii) Spare parts like SS sleeves, impeller, stage casing etc shall be measured and paid separately under relevant item of Sch \"A\". |
| 34 | Supply in replacement the following spares for repairs of Centrifugal pump set of 7.5 to 25 HP capacity complete all as specified and directed :- |
| 35 | (a) Ball bearing drive end for suitable size. |
| 36 | (b) Ball bearing for non driving end of suitable size. |
| 37 | (c)Gun Metal bush. |
| 38 | (d) CI impeller. |
| 39 | (e) MS pump shaft. |
| 40 | (f) Gland cover. |
| 41 | (g) Gland. |
| 42 | Supply in replacement the following spares for repairs of centrifugal / Monoblock pump set of up to 5 HP capacity complete all as specified and directed :- |
| 43 | Ball bearing suitable for induction motor. |
| 44 | Ball bearing for non drive end suitable for pump. |
| 45 | GM bush. |
| 46 | CI impeller. |
| 47 | MS pump shaft. |
| 48 | Gland cover. |
| 49 | M&L for rewinding of centrifugal motor with super enamelled copper conductor of same gauge, weight and turn to achieve its full efficiency including tying the windings and connecting the coils and brining the connections as that of existing one including renewal of worn out/unserviceable bearings etc complete all as specified and directed for following capacity :- |
| 50 | (a) Centrifugal motor 20 /25 HP capacity. |
| 51 | (b) Centrifugal motor 5.0/7.5HP capacity. |
| 52 | (c)Monoblock motor 1/3HP capacity. |
| 53 | M&L for Arrestingleakages of sluice valves by replacing Gland packing, gland bush, gland flange, nut bolts, gasket, packing material as required after dismantling in existing positionincluding testingon completion complete all as specified and directed for the following sizes:-Note: Quoted rates inclusive of the materialsmentioned above like Gland packing, gland bush, gland flange, nut bolts, gasket, packing material etc as required to arrest the leakages. |
| 54 | (a) 100 mm Dia |
| 55 | (b) 150 mm Dia |
| 56 | Supply and fix in replacement of unserviceableGun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipes and fixed complete all as specified and directed for the following sizes:- |
| 57 | (a)20mm dia bore |
| 58 | (b)25mm dia bore |
| 59 | (c)40mm dia bore |
| 60 | (d)50mm dia bore. |
| 61 | S&F in replacement of Cast Iron sluice valvesas per sample of swimming pool filtration plant, flanged ends stem of SS (AISI410) & Bronze (Gun Metal) working parts IS : 14846 both ends flanged with clamps and check nuts, operating wheel etc, non rising type K504, class PN 1.6 including jointing materials connecting and testing complete all as specified and directed :- |
| 62 | 100 mm Dia |
| 63 | 150 mm Dia |
| 64 | S&F, connecting and testing in repair of Cast Iron foot Valves 150 mm dia flanged ends swing type operation with rubber seat as per IS : 4038 single disc with all standard accessories and tested including replacement of nuts, bolts, washers, gaskets, packings etc complete all as specified and directed. |
| 65 | S&F, connecting and testing in repair of Cast Iron non return (Reflux) valves flanged ends in swing type design IS-5312 part-I, K517, PN-1.6, 150 mm dia both ends flanged etc including jointing materials of sizes complete all as specified and directed. |
| 66 | M&L for repairof ozonator unit of 100 gm/hrs, with oxygen concentrator complete all as directed including testing after installation. . Note : Quoted rates inclusive of testing in presence of authorised representative of manufacturer after installation . Quoted rates inclusive of all spare parts required for repairing of ozonator unit. |
| 67 | S&F in replacement Fully Automatic star-delta starter max motor output at 415V, 3 Phase, suitable for 25 HP Centrifugal pump, relay max range 14-23 Amp, model No MN 25 FASD heavy dutycomplete all as specified and directed. Make : L&T Cat Part No SS94364 or equivalent as approved. |
| 68 | S&F in replacement MCCB (Conforms to IEC : 60947-II / IS : 13947-II) in existing LT Panel box / feeder pillar boxes, adjustable & Fixed thermal magnetic setting of capacity 63 Amps, 3 pole, 16 KA, 415 Volts including disconnecting/Taking out existing old unsv/burned complete all as specified and directed. Addn/alt to the panel Boardfor fixing of MCCBis deemed to the quoted rates |
| 69 | S&F in replacement MCCB (Conforms to IEC : 60947-II / IS : 13947-II) in existing LT Panel box / feeder pillar boxes, Adjustable & Fixed thermal magnetic setting of capacity 160 Amps, 4 pole, 36 KA, 415 Volts including disconnecting/Taking out existing old unsv/burned complete all as specified and directed. Addn/alt to the panel Boardfor fixing of MCCBis deemed to the quoted rates |
| 70 | Supply and replace digital Ammeter(0-200/400 amps as per site requirement) with auxiliary supply voltage 415 volt complete all as specified and directed.Make L&T/AE/Secure |
| 71 | Supply and replace digital Voltmeter(0-500 volt) as per site requirement) with auxiliary supply voltage 415 volt complete all as specified and directed.Make L&T/AE/Secure |
| 72 | Supply and replace Water flow meter( M3/hr) at swimming pool plant room as per the existing make and model / equivalent complete all as specified and directed. |
| 73 | S&F in replacement of Cast Iron sluice valvesinstalled inside the balancing tank of AOC Swimming pool including its necessary arrangement to operate it from the top of the tank , flanged ends stem of SS (AISI410) & Bronze (Gun Metal) working parts IS : 14846 both ends flanged with clamps and check nuts, operating wheel etc,rising type K504, class PN 1.6 including jointing materials of 150 mm diaconnecting and testing complete all as specified and directed. |
| 74 | S&F in replacement of 200 mm dia Cast Iron sluice valvesas per sample of swimming pool filtration plant, flanged ends stem of SS (AISI410) & Bronze (Gun Metal) working parts IS : 14846 both ends flanged with clamps and check nuts, operating wheel etc, non rising type K504, class PN 1.6 including jointing materials connecting and testing complete all as specified and directed. |
| 75 | M&L in replacement of Pressure gauge 4\" dia, 0-21 Kg rating, 3000 PSI including jointing materials connecting and testing complete all as specified and directed. |
| 76 | Supply and fixing in replacement of gasket 200NB W/T NEOPRENE DIAPHRAGM floway valve Nylon reinforced Neoprene rubber diaphragm suitable for floway wear type diaphragm valve code No - HSN/SAC - 4000, suitable for 200 mm dia sluice valve, 14 Nos holes complete all as specified and directed. |
| 77 | Supply and fix in replacement of unserviceable 65 mm dia cast iron Gate valve, connected with iron wheel head, screwedat both ends for iron pipes and fixed complete all as specified and directed. |
| 78 | Supply and fix in replacement of unserviceable 25 mm dia cast iron Gate valve, connected with iron wheel head, screwedat both ends for iron pipes and fixed complete all as specified and directed. |
| 79 | Complete removal of existing treatment including preparation of old painted surfaces by washing, rubbing down and stopping of painted surfaces, painting with one coat of synthetic enamel paint of approved colour on centrifugal pump set of 25 HP capacity including inlet, outlet mains, coupling, sluice valve, non return valve, base plate, pully with safe guard, vacuum pipe line and writing the MES/SM number with black paint of suitable size of letters complete all as specified and directed. |
| 80 | Complete removal of existing treatment including preparation of old painted surfaces by washing, rubbing down and stopping of painted surfaces, painting with one coat of synthetic enamel paint of approved colour on horizontal type quarts sand filter ( 2 Nos) of capacity 50000 gln/hrs including inlet, outlet mains, coupling, sluice valve, non return valve, base plate, pully with safe guard, vacuum pipe line and all exposed pipe insite swimming pool plant roomand writing the MES/SM number with black paint of suitable size of letters complete all as specified and directed. |
| 81 | Supply in consumption Stequa 411 AE Refill: Chlorine tablets contained in plastic cylindrical sealed disposable sanitiser refill for disinfection of drinking water, suitable for operation through recommended dosing system. (i) Replacement indication: visual & weight variation (ii) Water contact orifice design: sealed when dry, exposed upon immersion (iii) Operation type: Non contact, non inhalatory (iv) Cylinder dia: 2.5 inches + 0.5 inches (v) Cylinder height : Minimum 10.0 inches + 0.5 inches (vi) Operational stipulations: (a) Heavy metal (Pb & Hg) contamination in the product media must be BDL as per AAS data (b) Minimum volume of water disinfected by each STEQUA 411 AE Refill to obtain disinfection activity of 1 ppm on spot (Influent water quality variation, ambient & site condition variations apply) as per absorbance data generated at λmax 515 nm. Three Hundred Fifty Thousand litres. |
| 82 | (c) Stability : Active ingredient stability (when stored at 25-45 degree Centigrade temp) must be at least 98% after one year as per data generated by accelerated Stability test protocol. (d) Safety & health hazard aspects on usage of the product media for regular drinking water disinfection: Heavy Metal contaminants (like Mercury & lead) in product media must be below detectable limit (BDL), and the product must pass the Acute Toxicity test (to specially confirm non toxicity for mammalian cells), based on which the product must be considered sate to use form human health safety point of view and freedom from toxicity when used in drinking water disinfection in recommended dosage. (e) The refills must ensure infrastructural safety (as per date generated by Electrolytic Conductivity (µs/cm) test protocol) and operators health safety (f) STEQUA Auto Economy Refill 41 AE must be complaint with operators health safety considering regular exposure. The brand and make of the sanitiser mus be stated and certified by a laboratory /study centre of any state University. |
| 83 | Supply in consumption STEQUA 412 HD: Plastic cylindrical sealed disposable floating sanitiser station for disinfection of swimming pool & cooling tower water containing algaecide & coagulant with arrangement for controlled release of active ingredients in water, and head suspender. Disinfection capacity: 16.0 LL Water at 0.5 ppm Ac Cl at release site (subject to site & raw water quality variations). (a) Replacement indication: visual & weight variation (b) Operation type: Non contact, non inhalatory (c) Cylinder Dia:2.5 inches + 0.5 inches (d) Cylinder Height: 26.0 inches+ 0.5 inches (e) Model: Stequa 412 HD |
| 84 | Supply in consumption Stequa Purity Verifier 41021 containing1 comparator with lid, 30 tablets x pH RAPID (Item code: PVPH 3041021), 30 tablets x Chlorine RAPID (Item code: PVFC 3041021), 1 instruction sheet, 1 plastic box. Note: pH range: 6.8-7.0-7.2-7.4-7.6-7.8-8.0-8.2. Chlorine range: 0.1-0.3-0.4-0.5-0.6-0.8-0.9-1.0-1.5-2.0-3.0 |
| 85 | Supply in consumption PVPH 41021 Packet of 100 tablets pH RAPID for STEQUA Purity Verifier 41021 |
| 86 | Supply in consumption PVPH 41021 Packet of 100 tablets Chlorine RAPID for STEQUA Purity Verifier 41021 |
| 87 | Disconnecting and removing the water and electric connections carefully from the existing submersible pump sets of capacity 3 HP to 10 HP and taking out the pump setalongwith pipes and fittings for flushing the bore wellup to 450 feet depth orrepair the pump set and strip opening the pump set for repairs/replacement of worn out spares, refixing of serviceable spares, assembling the pump set completely, testing of pump set, lowering the pump set inside the bore well after repairs including connecting back the water and electric connections, commissioning of pump set for satisfactory operation on its full load complete all as specified and directed. Note :-The spares required for repair the pump sets and rewinding of motors will be measured and paid separately. |
| 88 | M&L for rewinding the Submersible pump Motorwith PVC insulated,super enamelled copper conductor with ‘F’ class heavy grade insulation weight and turns to achieve its full efficiency including tying the winding and connecting the coils and brining the connections as that of existing one including applying insulating varnish, heating and backing the windings thoroughlyincluding taking down old existing copper winding complete all as specified and directed for Submersible pump motor of following capacity :- |
| 89 | Submersible Motor up to and including up to 5 HP. |
| 90 | Submersible Motor above 5 HP up to 10 HP. |
| 91 | Supply in replacement the following spares suitable for existing make of submersible pump set 3 to 10 HP capacity, multi stage for repairs complete all as specified and directed :- |
| 92 | Gun metal Impeller. |
| 93 | Stage casing. |
| 94 | SS Sleeves. |
| 95 | Middle bush.(LB) |
| 96 | Middle sleeve. |
| 97 | Discharge outlet.(LB) |
| 98 | Pump coupling. |
| 99 | DOL SS Sleeve. |
| 100 | Suction bush. |
| 101 | Pump Shaft |
| 102 | Motor thrust bearing sets |
| 103 | Motor housing Covers |
| 104 | Motor housing Brush |
| 105 | Motor adopter |
| 106 | Motor Bottom base |
| 107 | Replacement of Pump unit |
| 108 | Pump neck ring |
| 109 | Pump bowel Bush |
| 110 | S&F PVC insulated Copper conductor, sheathed, Submersible flat cables of size 4 Sqmm, 3 core,for Submersible Pumps, 1100 Volts grade, conforming to IS:694/1990 with latest amendments cutting to required length connecting with necessary end ferrules / water proof joints and jointing and testing including disconnecting/taking out old existing cable complete all as specified and directed. |
| 111 | Supply & fixing HDPE heavy duty column pipe in Bore wellinternal dia 50mm PN 16kq/Sqmm including allnecessary fittings and fixtures as requited for fixing with submersible motorComplete allas specified and directed.Note: Quoted rate inclusive offixing of pipe with submersible motor and lowering in existing bore well |
| 112 | Supply and fixing of DOL Starter suitable for up to 7.5 HP Motor, 5.5 KW and relay max range 20-32 Amp as in repairs complete all as specified and as directed.Makes : L&T cat part No CS90947 or equivalent of Havells/CG as approved. |
| 113 | Supply and fixing of single phase preventer suitable for up to 7.5 HP motor as in repairs complete all as specified and as directed.Make : L&T cat part No CS94824DOOO or equivalent of Havells/MINILAC |
| 114 | M&L for flushingof existing borewells of any sizeup to 250 Mtrs depth with drilling compressor mounted on truckincluding surging and flushing the bore at a pressure of 7 Kg / Sqcm with compressed air andflushing the sand, mud including flushing out tree roots etc from the bore well till discharge of the fresh water including testing of watersamples for chemical and bacteriological tests andcomplete all as specified and directed . |
