Gm/Cc/Pur/2024-25/8726-27 Techno Commericial Eligibility Document As Per Tender , Computer Items : , Tripping Coil 30 Volts Dc, Copper Wire, Shunt Suitable For Bhel With Assembly Specification:Operating Voltage : 30V Dc Coil Resistance : 4.8± 0.1 Ohmsbobbin- Outer Diameter : 42Mminner Diameter : 16Mm (With Brass Tube)Length: 93Mm Brass Tube Length : 98 Plunger Length : 140Mm Copper Wound And Varnished With 0.50 Meter Insulated Pvc 1.0 Sqmm Wire Weightz: 1) Coil : 505 Gms 2) Plunger : 126 Gms 3)Minimum Overall Weight Of Coil : 965 Gms With Nylock Style Nuts , 30 Volt Tripping Coil For Crompton Specification: Operating Voltage: 30V Dc Coil Resistance: 2.6 ± 0.1 Ohms Bobbin - Outer Diameter: 52Mm, Inner Diameter: 20Mm Height: 52Mm, Weight Of Coil: 300Gm , Tripping Coil 30 Volt Dc, Copper Wire, Shunt Suitable For Shreem Specification : Operating Voltage : 30V Dc Coil Resistance : 3.9 ± 4.3 Ohms Bobbin – Outer Diameter : 51Mm Innerdiameter : 26Mm Height : 51Mm Copper Wound With 0.5 Meter Insulated Pvc 1.5 Sqmm Wire Minimum Overall Weight Of Coil : 395 Gms , Tripping Coil 30 Volt For Abb, 11 Kv Vcb Specification: In 54450007-Y D : 0.609 N : 550 , Tripping Coil 30 Volt For Stelmec, 11 Kv Vcb With Assembly Specification: Operating Voltage : 30V Dc Coil Resistance : 3.1 ± 0.1 Ohms Make : Sunkid/Rabco Single, Metal Enclosed Coil Unit , Tripping Coil 30 Dc Volt For Schneider, 11 Kv Vcb Specification: Operating Voltage : 18-26V Dc Modal : Og835 Coil Resistance : 8.7 ± 0.1 Ohms Coil Bobbin – Outer Diameter : 46Mm Innerdiameter : 16Mm Length : 40Mm Copper Wound And Varnished With 0.50 Meter Insulated Pvc 1.0 Sqmm Wire Weight : 1) Coil : 225 Gms , 30 Volt Tripping Coil Megawin 525 Gm With Assembly Specification : Operating Voltage : 30V Dc Coil Resistance : 4.8± 0.1 Ohms Bobbin - Outer Diameter : 42Mm Inner Diameter : 16Mm (With Brass Tube) Length : 93Mm, Brass Tube Length : 98 Plunger Length : 140Mm, Copper Wound And Varnished With 0.50, Meter Insulated Pvc 1.0 Sqmm Wire Weight :1) Coil : 505Gm,2) Plunger : 126 Gm 3) Minimum Overall Weight Of Coil : 965 Gm With Nylock Style Nuts , Capacitor Bank Do Fuse (T-40) , Teflon Tape , Pvc Tape (Make: Steelgrip/Anchor Or Equivalent) , M Seal , Cone Washer 12Mm, 16Mm, 20Mm , Mobil Oil , Wd 40 , Grease , Hack Saw Blade :- 12” (Double Side)Make:- Sharp , Silica Gel Silica Gel Required For Power & Distribution Transformer Shall Be Conforming To Iss 3401/1992 With Its Latest Amendments. The Material Shall Be Solid With Grainy Porous Structure Free From Extraneous Impurities. The Indicating Type Gel Should Be Odorless. Non-Toxic & Non Corrosive With Stable Chemical And Thermal Characteristics. The Inter Connected Pores From A Vast Surface Area; Silica Gel Should Absorb Moisture 40% Or More Of Its Weight At 100% Humidity. Bulk Density: The Bulk Density Of The Material Shall Be More Than 0.6Gm./Ml. Particle Size & Colour: The Material Shall Be Blue In Colour And Its Size Should Be From 9 To 12Mm. Loss On Drying: The Material When Tested According To The Method Prescribed In Iss Shall Not Lose More Than 5% Of Its Mass. Absorption Capacity: The Material When Tested According To The Method Prescribed In Iss 3401-1992 Shall Absorb Minimum 27% Of Moisture On The Basis Of Its Mass. Ph Value: The Ph Of Aqueous Extract Of The Material When Determined By The Method Prescribed In Iss 3401-1992 Shall Not Be More Then 8 And Not Less Then 3.5. Loss On Attrition: When Subjected To The Test According To The Method Prescribed In Aforesaid Iss Not More Than 2.5% Of The Material Shall Pass Through The Sieve. Chemical Requirement: The Gel Shall Also Comply With The Requirement Prescribed In The Iss 3401-1992 , Cutting Pliers , Nose Plier , Nut Bolt M6 , Nut Bolt M8 , Nut Bolt M9 , Nut Bolt M10 , Nut Bolt M12 , Hole Saw Cutter 20Mm , Sand Paper
