|
| 1 | Repair/ maintainance/ servicing and checking thoroughly, defective centrifugal pump set of capacity 120 HP by dismantling of pump set at site and checking inspection and replacement of unserviceable spares as required or as specified and as directed.Note :- (a)Spares shall be measured and paid separately under relevant items as \"S&F in repairs\". (b) The work involves proper alignment after repairing, testing, recommissioning the pump set tothe entire satisfaction of Engineer-in-Charge. (c) Job shall be carried out by the authorised persons of the Manufacturer. |
| 2 | All as per serial item No 1 but pump set of capacity 100/90 HP. |
| 3 | All as per serial item No 1 but pump set of capacity 75 HP. |
| 4 | All as per serial item No 1 but pump set of capacity 60 HP. |
| 5 | All as per serial item No 1 but pump set of capacity 30 HP. |
| 6 | All as per serial item No 1 but pump set of capacity 25 HP. |
| 7 | S&F in repair, air release valve including making hole on pump for re-threading for 30 HP to 120 HP pump set complete all as specified and as directed |
| 8 | S&F in repairs, gland plate, nuts and bolts, both side of pump 04 Nos for 25 HP to 120 HP pump complete all as specified and as directed |
| 9 | S&F in repairs, water retaining (Deflector) ring DE/NDE for 120 HP pump set complete all as specified and as directed |
| 10 | S&F in repairs,spilt linter ring, CI, DE/NDE, for 120 HP pump set complete all as specified and as directed |
| 11 | S&F in repairs,cartridge for bearing, DE/NDE for 120 HP pump set complete all as specified and as directed |
| 12 | S&F in repairs, shaft sleeve, CI, DE/NDE for 120 HP pump set complete all as specified and as directed |
| 13 | S&F in repairs, stuffing box bush (Throat), CI, DE/NDE for 120 HP pump set complete all as specified and as directed |
| 14 | S&F in repairs, gland plate with gland packing, CI, for 120 HP pump set complete all as specified and as directed |
| 15 | S&F in repairs, set of gasket for 120 HP pump set complete all as specified and as directed |
| 16 | S&F in repairs, set of \"O\" ring, for 120 HP pump set complete all as specified and as directed |
| 17 | S&F in repairs, wear ring, CI, for 120 HP pump set complete all as specified and as directed |
| 18 | S&F in repairs, impeller CI stage-I for 100/90 HP pump set complete all as specified and as directed |
| 19 | S&F in repairs, impeller CI stage-II for 100/90 HP pump set complete all as specified and as directed |
| 20 | S&F in repairs, pump shaft C-40 including sleeves for 100/90 HP pump set complete all as specified and as directed |
| 21 | S&F in repairs, water retaining (Deflector) ring DE/NDE for 100/90 HP pump set complete all as specified and as directed |
| 22 | S&F in repairs, spilt linter ring CI DE/NDE for 100/90 HP pump set complete all as specified and as directed |
| 23 | S&F in repairs, cartridge for bearing DE/NDE for 100/90 HP pump set complete all as specified and as directed |
| 24 | S&F in repairs, shaft sleeve CI DE/NDE for 100/90 HP pump set complete all as specified and as directed |
| 25 | S&F in repairs, stuffing box bush (Throat) CI DE/NDE for 100/90 HP pump set complete all as specified and as directed |
| 26 | S&F in repairs, gland plate with gland packing CI for 100/90 HP pump set complete all as specified and as directed |
| 27 | S&F in repairs, set of gasket for 100/90 HP pump set complete all as specified and as directed |
| 28 | S&F in repairs, set of \"O\" ring for 100/90 HP pump set complete all as specified and as directed |
| 29 | S&F in repairs, wear ring CI for 100/90 HP pump set complete all as specified and as directed |
| 30 | S&F in repairs, impeller CI stage -I for 75 HP pump set complete all as specified and as directed |
| 31 | S&F in repairs, impeller CI stage -II for 75 HP pump set complete all as specified and as directed |
| 32 | S&F in repairs, pump shaftincluding sleeves for 75 HP pump set complete all as specified and as directed |
| 33 | S&F in repairs, water retaining (Deflector) ring DE/NDE for 75 HP pump set complete all as specified and as directed |
| 34 | S&F in repairs, linter ring CI DE/NDE for 75 HP pump set complete all as specified and as directed |
| 35 | S&F in repairs, Cartridge for bearing DE/NDE for 75 HP Pump set complete all as specified and as directed |
| 36 | S&F in repairs, shaft sleeve CI DE/NDE for 75 HP pump set complete all as specified and as directed |
| 37 | S&F in repairs, stuffing box bush (Throat) CI DE/NDE for 75 HP pump set complete all as specified and as directed |
| 38 | S&F in repairs, gland plate with gland packing CI for 75 HP pump set complete all as specified and as directed |
| 39 | S&F in repairs, set of gasket for 75 HP pump set complete all as specified and as directed |
| 40 | S&F in repairs, set of \"O\" ring for 75 HP pump set complete all as specified and as directed |
| 41 | S&F in repairs, wear ring CI for 75 HP pump set complete all as specified and as directed |
| 42 | S&F in repairs, impeller CI stage -I for 60 HP pump set complete all as specified and as directed |
| 43 | S&F in repairs, impeller CI stage -II for 60 HP pump set complete all as specified and as directed |
| 44 | S&F in repairs, pump shaftincluding sleeves for 60 HP pump set complete all as specified and as directed |
| 45 | S&F in repairs, water retaining (Deflector) ring DE/NDE for 60 HP pump set complete all as specified and as directed |
| 46 | S&F in repairs, linter ring CI DE/NDE for 60 HP pump set complete all as specified and as directed. |
| 47 | S&F in repairs, cartridge for bearing DE/NDE for 60 HP pump set complete all as specified and as directed |
| 48 | S&F in repairs, shaft Sleeve CI DE/NDE for 60 HP pump set complete all as specified and as directed |
| 49 | S&F in repairs, stuffing box bush (Throat) CI DE/NDE for 60 HP pump set complete all as specified and as directed |
| 50 | S&F in repairs, gland plate with gland packing CI for 60 HP pump set complete all as specified and as directed |
| 51 | S&F in repairs, set of gasket for 60 HP pump set complete all as specified and as directed |
| 52 | S&F in repairs, set of \"O\" ring for 60 HP pump set complete all as specified and as directed complete all as specified and as directed |
| 53 | S&F in repairs, wear ring CI for 60 HP pump set complete all as specified and as directed |
| 54 | S&F in repairs, impeller CI for 30 HP pump set complete all as specified and as directed |
| 55 | S&F in repairs, pump shaftincluding sleeves for 30 HP pump set complete all as specified and as directed |
| 56 | S&F in repairs, water retaining (Deflector) ring DE/NDE for 30 HP pump set complete all as specified and as directed |
| 57 | S&F in repairs, linter Ring CI DE/NDE for 30 HP pump set complete all as specified and as directed |
| 58 | S&F in repairs, cartridge for bearing DE/NDE for 30 HP pump set complete all as specified and as directed |
| 59 | S&F in repairs, shaft sleeve CI DE/NDE for 30 HP pump set complete all as specified and as directed |
| 60 | S&F in repairs, stuffing box bush (Throat) CI DE/NDE for 30 HP pump set complete all as specified and as directed |
| 61 | S&F in repairs, gland plate with gland packing CI for 30 HP pump set complete all as specified and as directed |
| 62 | S&F in repairs, set of gasket for 30 HP pump set complete all as specified and as directed |
| 63 | S&F in repairs, set of \"O\" ring for 30 HP pump set complete all as specified and as directed |
| 64 | S&F in repairs, wear ring CI for 30 HP pump set complete all as specified and as directed |
| 65 | S&F in repairs, impeller CI for 25 HP pump set complete all as specified and as directed |
| 66 | S&F in repairs, pump shaftincluding sleeves for 25 HP pump set complete all as specified and as directed |
| 67 | S&F in repairs, water retaining (Deflector) ring DE/NDE for 25 HP pump set complete all as specified and as directed |
| 68 | S&F in repairs, linter Ring CI DE/NDE for 25 HP pump set complete all as specified and as directed |
| 69 | S&F in repairs, cartridge for bearing DE/NDE for 25 HP pump set complete all as specified and as directed |
| 70 | S&F in repairs, shaft sleeve CI DE/NDE for 25 HP pump set complete all as specified and as directed |
| 71 | S&F in repairs, stuffing box bush (Throat) CI DE/NDE for 25 HP pump set complete all as specified and as directed |
| 72 | S&F in repairs, gland plate with gland packing CI for 25 HP pump set complete all as specified and as directed |
| 73 | S&F in repairs, set of gasket for 25 HP pump set complete all as specified and as directed |
| 74 | S&F in repairs, set of \"O\" ring for 25 HP pump set complete all as specified and as directed |
| 75 | S&F in repairs, wear ring CI for 25 HP pump set complete all as specified and as directed |
| 76 | Dismantling and taking down unserviceable electric motor of 120 HP capacity of pump set from foundation and transportation to workshop for repairing, opening and rewinding withnew super enamelled copper insulated winding wire as per existing gauge of copper wire, winding with insulating material, varnishing, heating etc and reassembling, transporting back to site of work and installing on existing foundation including proper alignment and testing complete all as specified and as directed.Note :- All disturbed surfaces shall be made good to match the eixisting surfaces without any extra cost to the department. |
| 77 | All as per serial item No 76 but electric motor of 100/90 HP capacity of pump set complete all as specified and as directed. |
| 78 | All as per serial item No 76 but electric motor of 75 HP capacity of pump set complete all as specified and as directed complete all as specified and as directed. |
| 79 | All as per serial item No 76 but electric motor of 60 HP capacity of pump set complete all as specified and as directed. |
| 80 | All as per serial item No 76 but electric motor of 30 HP capacity of pump set complete all as specified and as directed. |
| 81 | All as per serial item No 76 but electric motor of 25 HP capacity of pump set complete all as specified and as directed. |
| 82 | S&F ball bearing suitable for 120 HP capacity pump including bearing checknut, press washer, shaft brass nutincluding taking out old unserviceable bearing all as specified and as directed |
| 83 | S&F ball bearing suitable for100/90 HP capacity pumpincluding bearing checknut, press washer, shaft brass nutincluding taking out old unserviceable bearing all as specified and as directed |
| 84 | S&F ball bearing suitable for75 HP capacity pumpincluding bearing checknut, press washer, shaft brass nutincluding taking out old unserviceable bearing all as specified and as directed |
| 85 | S&F ball bearing suitable for60 HP capacity pumpincluding bearing checknut press washer shaft brass nutincluding taking out old unserviceable bearing all as specified and as directed |
| 86 | S&F ball bearing suitable for30 HP capacity pumpincluding bearing checknut, press washer, shaft brass nutincluding taking out old unserviceable bearing all as specified and as directed |
| 87 | S&F ball bearing suitable for25 HP capacity pumpincluding bearing checknut, press washer, shaft brass nutincluding taking out old unserviceable bearing all as specified and as directed |
| 88 | S&F ball bearing suitable for 120 HP capacity motor including cir clip including taking out old unserviceable bearing all as specified and as directed |
| 89 | S&F ball bearing suitable for100/90 HP capacity motor including cir clip including taking out old unserviceable bearing all as specified and as directed |
| 90 | S&F ball bearing suitable for75 HP capacity motor including cir clip including taking out old unserviceable bearing all as specified and as directed |
| 91 | S&F ball bearing suitable for60 HP capacity motor including cir clip including taking out old unserviceable bearing all as specified and as directed |
| 92 | S&F ball bearing suitable for30 HP capacity motor including cir clip including taking out old unserviceable bearing all as specified and as directed |
| 93 | S&F ball bearing suitable for25 HP capacity motor including cir clip including taking out old unserviceable bearing all as specified and as directed |
| 94 | S&F in repairs, coupling bushes with studs of existing type and size suitable for 25 HP to 120 HP pump set all as specified and as directed. |
| 95 | S&F in repairs, coupling star bushof existing type and size suitable for 25HP to 120 HP Pump setall as specified and as directed. |
| 96 | S&F in repairs, love-joy / flexible type coupling,made out of MS, complete suitable for 25 HP to120HP pump set, including rubber star bush/rubber bush with nut bolts, metal filling existing shaft of motor/ pumpand re-grinding, making key slot etc and testing with zero level alignment complete all as specified and as directed. |
| 97 | M&L in repairs for foundation of motor pump set of 100/ 90/ 75/ 60/ 30/ 25 HP by removing and taking out pump motor from foundation by unscrewing the nuts bolts and keeping away, cutting, welding and machining with and including flat iron or channel of 50 x 6 mm flat iron and channel MC 75 to MC 150 size as required for strengthing the foundation plate, cutting and replacing / shifting and welding at proper fixing ofmotor on foundation including connections, replacement of foundation nut bolts, washers, with accurate realignment of motor with pump to avoid vibration and smooth running of pump on full load, testing and commissioning complete all as directed. Note:- The quotedrate shall be deemed to be inclusive of all civil works including PCC 1:2:4, type B2 as in foundation and grounting work including necessary form work, plaster etc complete. |
| 98 | S&F in repairs, Pressure gauge (complete set etc. GI bend pipe, nipples, operating switch / valve) of capacity 0-100 kg as per samplesuitable for 25 to 100 HP pump set complete all as specified and as directed. |
| 99 | S&F in repairs, single phase preventor, suitable for 100/90/75/60/25 HP pump set starter, 415/440 Volt, 50 Hz all as specified and as directed. |
| 100 | S&F in repairs, ML6/ML4/ML2 starter timer, suitable/existing capacityfor 100/90/75/60/25 HP pump set starter, 415/440 Volt, 50 Hzall as specified and as directed. |
| 101 | S&F in repairs, 3 pole power contactors, TYPE -MNX-95 conforming to IS/IEC 60947-4-1 and IEC 6947-1 Amp rating 95 Amps (MNX95) along with add on TOP 2 NO+ 2 NC or add on side fixed in existing FASD starter complete all as specified and as directed. |
| 102 | S&F in repairs, 3 pole power contactors, TYPE -MNX -70 conforming to IS/IEC 60947-4-1and IEC 6947-1 Amp rating 70 Amps (MNX70) fixed in existing FASD starter complete all as specified and as directed. |
| 103 | S&F in repairs, spare contact kit and spare coil as per L&TCat No SS-95311 and SS91258 or equivalentin Siemens/Crompton suitable for ML-4 starter complete all as specified and as directed. |
| 104 | S&F in repairs, spare contact kit and spare coil as per L&TCat part No SS-95313 and SS91258 or equivalentin Siemens/Crompton suitable for ML-6 starter complete all as specified and as directed. |
| 105 | S&F 3 pole power contactor ML-2 TP 32 Amps capacity suitable for operation on 415 Volts 50 Hz, AC supply complete includng taking out old unserviceable power contactor from panel board all as specified and as directed. |
| 106 | S&F 3 pole power contactor ML-3 TP 40 Amps capacity suitable for operation on 415 Volts 50 Hz, AC supply complete including taking out old unserviceable power contactorfrom panel board all as specified and as directed. |
| 107 | S&F 3 polepower contactor ML-4 TP 70 Amps capacity suitable for operation on 415 Volts 50 Hz, AC supply complete including taking out old unserviceable pole power contactor from panel board all as specified and as directed. |
| 108 | S&F 3 pole power contactor ML-6 TP 110 Amps capacity suitable for operation on 415 Volts 50 Hz AC supply complete including taking out old unserviceable power contactorfrom panel board all as specified and as directed. |
| 109 | S&F in repairs, spare contact Kit TYPE -ML 2, fixed in existing FASD starter complete all as specified and as directed. |
| 110 | S&F in repairs, spare contact Kit TYPE -ML 4,fixed in existing FASD starter complete all as specified and as directed. |
| 111 | S&F in repairs, spare contact Kit TYPE -ML 6,fixed in existing FASD starter complete all as specified and as directed. |
| 112 | S&F in repairs, spare coil TYPE -ML 2,fixed in existing FASD starter complete all as specified and as directed. |
| 113 | S&F in repairs, spare coil TYPE -ML 4,fixed in existing FASD starter complete all as specified and as directed. |
| 114 | S&F in repairs, spare coil TYPE -ML 6,fixed in existing FASD starter complete all as specified and as directed. |
| 115 | S&F in repairs, Thermal Overload Relays TYPE -ML 2/3, fixed in existing FASD starter complete all as specified and as directed. |
| 116 | S&F in repairs, on load change over switch 415 Volts in sheet metal enclosures, three phase, four pole, 400 Amps capacity,all as specified and as directed. |
| 117 | S&F in repairs, on load change over switch 415 Volts in sheet metal enclosures, three phase, four pole, 200 Amps capacity,all as specified and as directed. |
| 118 | M&L in replacement, earthing complete with galvanized steel earth plate electrode 60 cm X 60 cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level, connecting to the GI earth strip 32 mm x 6 mm, by means of nut bolts, check nuts and washer of the GI . Earth wire connected upto main earth point/DBs alongwith 40mm dia GI pipe, light grade,including provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40 mm thick RCC (1:2:4)cover with reinforced with XPM (weight not less than 4 Kg / Sqm) and frame of angle iron 25mm X 25 mm X 3mm with lugs 2 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh andearth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding than 50 mtr, all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point all as specified including testing on completion. |
| 119 | M&L for repairs/refixing of loose GI earthing strip of size 32 mm x 6 mm thick on and including wooden gutties connecting to earthing and the test point of the lightening arrester of the overhead tank all as per existing and as directed.Note : GI strip, if corroded will be replaced by new where directed and the same shall be measured & paid separately as \"Supply only\" under respective item |
| 120 | S&F in repairs, 4 Pole, MCCB, 400 Amp, 50 Hz, 415 Volts, adjustable type with rupturing capacity 36 KA all as specified and as directed. |
| 121 | S&F in repairs, 4 Pole, MCCB, 250 Amp, 50 Hz, 415 Volts, adjustable type with rupturing capacity 36 KA all as specified and as directed. |
| 122 | S&F in repairs, 4 Pole, MCCB, 200 Amp, 50 Hz, 415 Volts, adjustable type with rupturing capacity 36 KA all as specified and as directed. |
| 123 | S&F in repairs, 4 Pole, MCCB, 125 Amp, 50 Hz, 415 Volts, adjustable type with rupturing capacity 36 KA all as specified and as directed. |
| 124 | S&F in repairs, 4 Pole, MCCB, 160 Amp, 50 Hz, 415 Volts, adjustable type with rupturing capacity 36 KA all as specified and as directed. |
| 125 | M&L in repair of LT panel wiring with new wiring using new cables of same size as per approved makes givenincluding replacement of lugs, thimbles etc complete all as specified and as directed . |
| 126 | M&L for replacement of LT panel CT coils as per exiting size and make complete all as specified and directed. |
| 127 | M&L for replacement of R Y B phase indicators complete set of make as per existing complete all as specfied and as directed. |
| 128 | S&F 1100 volts grade heavy duty cable, 50 sqmm, single core, PVC insulated, copper conductor, served with inner sheathing of PVC tape and overall PVC sheathed including taking down old unserviceable cable all as specified and as directed. |
| 129 | M&L in repairs for PTFE TeflonGraphite gland packing rope ofsize 10mm/12mm/14mmall as specified and as directed. |
| 130 | Supply only bearing grease HP/BP type servo Gem Natra-3/Lithon-3 in 5 kg packall as specified and as directed. |
| 131 | Supply & filling, engine oil 20 W 40 turbo synthetic superior quality engine oil including taking out old oil all as specified and as directed. |
| 132 | Taking up or down choked GI water mains, 80 mm bore including all fittings and proper cleaning by internal brushing, removing chalkings and refixing / relaying in place, jointing, pressure testing and washing out complete all as specified and as directed. |
| 133 | All as per serial item No 132 but 100 mm bore. |
| 134 | Taking up or down choked CI water mains, 150 mm bore including all fittings with spigot and socket ends including burning out joints, removing lead and proper cleaning by internal brushing, removing chalking and refixing/ relaying in place, jointing, pressure testing and washing out complete all as specified and as directed. Note : Run lead joints shall be measured and paid seperately. |
| 135 | All as per serial item No 134 here-in-before but for 200 mm bore. |
| 136 | All as per serial item No 134 here-in-before but for 250 mm bore. |
| 137 | M&L for 80mm bore GI tubing, medium grade laid in trenches / floors or fixed to wall in any length with screwed and socket joints together with all galvanised GI fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc and pressure testing, washing out complete including taking out old pipes and fittings all as specified and as directed. |
| 138 | All as per serial item No 137 here-in-before but for 100 mm bore. |
| 139 | M&L for DN 150 mm bore ductile Iron pipe with spigot and socket ends, centrifugally cast, class DI-K9, with finishing layer of bituminous coating as per annex C of IS 8329, including making threading, cutting, jointing forfixing flange as required at site conforming to IS: 8329 : 2000, ISI marked, in any length, laid in trenches , pressure testing, washing out including taking out old pipes and fittings complete all as specified and as directed. |
| 140 | All as per serial item No 139 here-in-before but for 200 mm bore. |
| 141 | All as per serial item No 139 here-in-before but for 250 mm bore. |
| 142 | M&L for CI / DI fittings and specials such as Bends (any type, radius and angle), Tapers any type (straight, bend, increasing, decreasing or double socket etc.), Tee pieces single branch, \"Y\" junction, double branch, cross (all sockets or socket and spigot), Collars, Caps, Plugs, Connecting pieces one end flanged and other end socketed or spigot ends or all socketed / spigot ends etc, suitable upto 150 mm bore pipe complete all as specified and as directed. |
| 143 | All as per serial item No 142 here-in-before but for 200 to 600 mm bore pipe. |
| 144 | M&L for run lead joints suitable for 150mm bore dia pipe, spigot and socket ends complete and pressure testing all as specified and asdirected. |
| 145 | All as per serial item No 144 but for 200 mm bore pipe. |
| 146 | All as per serial item No 144 here-in-before but for 250 mm bore pipe. |
| 147 | S&F rubber linednon return valve, B-02 (Ball Type) for 80 mm bore size, cast iron body, flanged end, including neophrene ball and by pass arrangement complete including suitable flanges, nuts, bolts, washers and rubbber gaskets including dismantling and taking down old unserviceable non return valve all as specified and as directed. |
| 148 | All as per serial item No 147 but 100 mm bore. |
| 149 | All as per serial item No 147 but 150 mm bore. |
| 150 | M&L for cast iron body, ball type, foot valve, flanged B-05(N) of 80mm bore size, including suitable flanges, nuts, bolts, washers and rubbber gaskets including dismantling and taking down old unserviceable foot valveall as specified & as directed. |
| 151 | All as per serial item No 150 but 100 mm size. |
| 152 | All as per serial item No 150 but 150 mm size. |
| 153 | All as per serial item No 150 but 200 mm size. |
| 154 | Cleaning of area around OH tanks, UG sumps, water supply installations by cutting and dressing of the existing vegetation (i.e. Small trees/ bushes/ plants/ grass, etc) and removing the same from premisesall as specified and as directed. |
| 155 | M&L for chamber cover, fabricated out of angle iron of size 40mm x 40mm x 6 mm in framework, 3mm thick MS sheet cover, flat iron 40mm x 6mm all around and diagonally and hinged to the angle iron frame work with locking arragements and handle, duly painted with two coats of anticorrosive bituminous paint over a coat of anticorrosive bituminous primer and fixed in PCC 1:2:4 coping, plaster and white wash etccomplete including taking down existing chamber coverall as specified and as directed. |
| 156 | Supply only calcium hypo chlorite, dry free flowing and free from lumps of following generic specification: (a) Aailable Chlorine - Min 65 % (b) Particle size ( passing through 1.70 mm IS sieve) - min 99.5 % (c) water insoluble matter - max 6%(d) calcium hydroxide- max 4% (e) Sodium chloride- 15%complete all as specifed and diected .Make : Any make approved by E-in-Cs Branch . |
| 157 | M&L for dewatering, cleaning of OH reservoir,1,00,000 gallons capacity, with staging of tank exc 15 m but not exc 24 m at location \"AC Depot pump house with high pressure jet to remove all mosses, algae, dirt, deposits and other sediments, scrubbing of internal surface with steel wire brush and removal of dirty water with sludge machines / industrial vacuum cleaners and disposal of the same to a safe distance including , sterilizing the complete, internal surface of the tank by using ISI mark, Grade-I bleaching powder / Liquid Chlorine, wash with fresh water, drying up and writing the words on external wall at visible place \"\"Military Engineer Services, Tank Capacity & Date of Cleaning\"\"using synthetic enamel paint in white colour over black background and letters of height 50 mm height and 40 mm width complete all as specified and as directed. |
| 158 | All as per serial item No 157but OH reservoir 50,000 gallons capacity with staging of tank exc 15m but n exc 24m at location\"AC Depot Pump House & CQA(V)\" . |
| 159 | All as per serial item No 157butUG Sump of 14,00,000 gallons capacity at location \" Dhobhighat Pump House\" |
| 160 | All as per serial item No 157butUG Sump of 8,00,000 gallons capacity at location \" Bhingar Pump House\" |
| 161 | All as per serial item No 157butUG Sump of 5,00,000 gallons capacity at location \" KLP, Dhobighat\" |
| 162 | All as per serial item No 157butUG Sump of 4,00,000 gallons capacity at location \" Jk Road family qtrs\" |
| 163 | All as per serial item No 157butUG Sump of 2,50,000 gallons capacity at location \" Dhobighat Pump House\" |
| 164 | All as per serial item No 157butUG Sump of 1,50,000 gallons capacity at location \" AC Depot Pump House\" |
| 165 | All as per serial item No 157butUG Sump of 75,000 gallons capacity at location \" AC Depot Pump House\" |
| 166 | All as per serial item No 157butUG Sump of 30,000 gallons capacity at location \"Bhingar Pump House\" |
| 167 | M&L for preparation of old steel surfaces of ladder for 20m staging of overhead water tank and applying one coat ofsynthetic enamel black paint all as specified and as directed. |
| 168 | M&L for PVC netlon jallies with woodenbattens of sectional area n exc 13 Sqcm,wooden beads n exc 75 mm girth duly fixed with nails, and fitted on top entry of over head reservoir and specified windows to prevent entry of birds/dirt particles all as specified and asdirected. |
| 169 | M&L for taking down carefully, existing unservicable water level Indicator from OH tank/ UG sump and repair with and including replacement of steel wire 4mm dia (8 SWG), MS V shaped pully 3 NOs, PVC Float 01 Nos, MS indicator, scraping, cleaning and painting steel surfaces complete, marking levels with night glow radium paint and fixing in position and testing for proper function complete all as specified and as directed. |
| 170 | M&L for complete removal of old paint by scrapping, cleaning steel surface, preparation and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and as directed. |
| 171 | M&L for complete removal of old paint by scrapping, cleaning gun metal surface of sluice valves/non return valves of any size, preparation and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and as directed. |
| 172 | M&L for preparation of old external surfaces of MS ERW pipes exc 10 cm width or girth and applying one coat of black bituminus paintcomplete all as specified and as directed. |
| 173 | M&L for complete removal existing paint,preparation of old steel and iron surface of any description over 10cm width or girth and applyingtwo coats of synthetic enemel paint overa coat of zink cromate primer complete all as specified and as directed. |
| 174 | Supply and laying in trenches or fixing or passing through pipe, 1100 Volts grade, armoured, heavy duty LT UG cable of size 50 Sqmm, 3.5 core with XLPE insulated stranded aluminium conductorincluding cablegland, lugs, testingandcommissioning including taking out existing cable alongwith protection covers complete allasspecified and as directed. |
| 175 | Supply and lay DWC HDPE PIPE (PE 100,SDR-21,6 Kgf/Sqcm) IS 4984-2016) 63 mm dia for laying of LT cables etc complete with all accessories all as specified and as directed. |
| 176 | M&L for providing and fixing stainless steel railing made of hollow tubes, channels, plates for ladder / part of ladder for OH reservoirs/ having staging up to 24 mtrs or underground sumps, with stainless steel including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories on wall/floor and taking out old rusted iron ladder complete all as specified and as directed. |
| 177 | Supply, install, testing and commissioningin replacement of factory made and tested (including CPRI type test certified) LT Panel boxIndoor type, floor mounted, compartmantalised and IP-54 suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, all as specified and directed, having bus bar chamber with insulated Allumanium bus bars of size 25 X 5 installed on porcelain insulators.The panel shall be dust and vermin proof, made of 3.15 mm CRCA MS sheet and with base frame of 40x40x6mm angle iron , powder coated, Front and rear opening type with aprons for cable entry with double doorshutter and locking arrangement comprises of following items including taking down existing pannel box with framework 800 W X 800 H X 400 Dall as specified and as directed. Location : BhingharPump House Main In comer :-(a)MCCB 80 Amps, 3 pole, 25 KA, 415 volts grade with thermal magnetic - 01 No(b) Digital Volt meter and Amp meter - 01 Nos ,415 volts, 50 Hz AC supply -01 set. (c)Neon indicating lamps (R, Y & B) -01 Set. (d) 6 A , sp mcb - 04 Nos, (e)CT. 100/5 A - 03 No OUTGOING :-(a) MCCB 63 A, TP , 25 KA - 02 Nos , b) CONTACTOR MNX 18 - 04 Nos c) CONTACTOR MNX 12- 02 Nos d)S-D TIMER- 02 Nos e) Tharmal Overload Relay 09-15 - 02 Nosf)PUSH BUTTON LED- 04 Nosg) TRIP INDICATOR- 02 Nos h) Starter 15HP FASD Fully automatic star delta starter Make - L&T - 02 setNote : Panel design will be approved by GE. |
| 178 | Dismantling and taking out unserviceable electric sumersible pump set15HP capacity from borewell and transportation to and from workshop, for repairing and rewinding with existing size copper wire, winding with insulating material and warnishing heating etc and reassembly installing including proper alignment and testing complete all as specified and directed. |
| 179 | S&F thrust bearing suitable for 15 Hp including lathe machine work all as specified and as directed. |
| 180 | S&F SS Coupling to connect DE and NDE ends of motor and pumps with locking pinssuitable for 15 HP all as specified and as directed. |
| 181 | S&F SS Coupling / adopter, suitable to connect HDPE pipe to pump outlet with MS clips all as specified and as directed. |
