|
| 1 | Taking down shutters of any description exc 1sqm andn.exc 2 sqm each and refixing in the same opening after repairing including replacement of damaged sections (replaced aluminium sections shall be measured and paid separately ) |
| 2 | Taking down shutters of any description exc 2 sqm each and refixing in the same opening after repairing including replacement of damaged sections (replaced aluminium sections shall be measured and paid separately) |
| 3 | S&Faluminium anodisedsections of various sizes required for frame and shutters of doors, windows, ventilators and partition with one or more rebates etc.including necessary joining cleats, glazing clips, beading,rubber packing, screws and all other fittings like locking arrangement for shutters etc. all as specified and directed by Engr-in-charge |
| 4 | Note:- |
| 5 | (i) Glazing/wiremesh shall be measured and paid separately. |
| 6 | (ii)Item shall be paid as per the weight of Aluminium section however the rate quoted shall be inclusive of the cost of neoprene beading glazing pins, screws, handle etc which shall not be measured for arriving the weight. |
| 7 | Taking down old aluminium windows or partition of any description and in any position |
| 8 | S&Fpowder coated aluminium (minimum thickness of powder coating 50 micron) for doors, windows, ventilators and partitionswith extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make confirming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified.Note:-(i) Glazing/wiremesh shall be measured and paid separately.(ii)Item shall be paid as per the weight of Aluminium section however the rate quoted shall be inclusive of the cost of neoprene beading glazing pins, screws, handle,hinges etc which shall not be measured for arriving the weight. |
| 9 | Taking down shutters of any description exc 1 sqm and not exc 2sqm each. |
| 10 | S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including teak wood lipping |
| 11 | S&F in repair9mm thick 600x600mm size gypsum tiles false ceiling with aluminium anodized snap grid of size605 mm x 605 mm with aluminium anodized angle 20 mm x 20 mm x 1.2 mm fixed to wall along the perimeter of ceiling with the help of nylon sleeves & screws, at 610mm centres and main and cross tees of size 31.75 mm x 31.75 mm x 1.6mm & 25.4 mm x 25.4 mm x 1.22 mm respectively with ceiling cleats / angle brackets of size 15 mm x 15 mm x 1.5 mmincluding 4 mm dia.G.I.wire suspended from the soffit at 1220 mm centres (upto 1200 mm length maximum) fixed to roof slabs by means of steel expansion fasteners10mm dia. complete all as specified and directed. |
| 12 | Supply and fix in repair 9 mm thick 600x600mm size gypsum pre laminated tiles on false ceiling (As per IS : 2095-1996: Part I) suitable for existing anodised aluminium frame of existing pattern and suitable for opening in the ceiling grid including taking down and refixing the existing grid etccomplete all as specified and directed |
| 13 | Supply and fixin repair plain ceiling system consisting of 600 mm x 600mm tiles (As per IS: 2095-1996: Part I) of pre coated galvanised aluminium in 0.7 mm thickness in required colour to be laid “on Armstrong/Hunter Duoglas grid systems/equivalent make as specified in Appx \"B\" of PS hereinafter with 15 mm wide T - section flanges in required colour having rotary stitching on the 1200 mm & 600 mm cross tees. The grid should be GI of make“Armstrong/Gyproc /equivalent make ”with 15mm wide T - section flanges in required colourshadehaving rotary stitching on all T sections i.e. the main runner, 1200 mm & 600 mm.Tees with a web height of 32 mm.Perimeter trim to be Armstrong/Gyproc/equivalent make as specified in Appx \"B\" of PS hereinafter, wall angles of size 19x19mm, secured to walls at 450 mm maximum centres including necessary fitting and 6 mm GI suspenders fixed to slab using steel fastener in ceiling all as specified and directed. |
| 14 | S&F in repairs Double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed.make: hyper, hardwyn of model as per site requirement |
| 15 | S&Faluminum anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts etc complete of size 300mm |
| 16 | S&Fin repair aluminum anodoised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts etc complete of size 300mm |
| 17 | M&L for preparation of new wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of primer all as specified and directed |
| 18 | S & F in repairs 18/ 19mm thick plywood grade BWR fixed with screws including fixing and polishing teakwood beading 4mm thick to exposed sides, as in cupboards, shutters ,panelling etc including necessary fixing arrangements as directed by Engineer in Charge. |
| 19 | S & F in repairs 12mm thick plywood grade BWR fixed with screws including fixed with screws/teakwood beading/aluminium beadingto wooden or Aluminium frame worketc.complete all as specified and directed.((New aluminium sections shall be msrd and paid seperately) |
| 20 | M & L0.9 mm decorative laminate type 1 of surface finish , colour and pattern as approved, fixed with approved adhesive as per manufacturer\"s instruction |
| 21 | Supply and fix in repair 12 mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws/aluminium beadingto Aluminium frame worketc.complete all as specified and directed.((New aluminium sections shall be msrd and paid seperately) |
| 22 | M & L for preparation of newwooden surfaces of any description over 10 cm in width or girth and finish the wood surface with two coats of synthetic varnishing over undercoat of varnish/polishoverfiller liquid transparent and make the surface fully shined complete all as specified and directed by Engr-in-Charge |
| 23 | Material and labour for cleaning and preparation of new wooden surfaces of any description, width or girth and applying two coats of french polish over a coat of wood filleron new work with two o more coats etc. complete all as specified and directed |
| 24 | S & F in repairs stainless steel handle 100mm long |
| 25 | S&F in repairs stainless steel clipon hinges size 100mm *12mm with flap open |
| 26 | S & F in repairs SSHasp & staple 75mm |
| 27 | Fixing cubboardto plastered surfaces(brick/concrete) using necessary anchors, fasteners, nut ,bolt etc including all connected fittings |
| 28 | Hacking out old broken glass (any thickness size, quality or description) from wooden frames ,glass doors , Partition or glazedwith putty or fixed with beads |
| 29 | S & F sheet glasses,plain4.80mm to 5MMthickglazingall withaluminum beading, glazing pin etc, or with oil putty in squaren exc .5 sqm in each pane |
| 30 | .-do-- all as above but exc 0.5 sqm in each pane |
| 31 | S & F sheet glasses,opaque / frosted on one side 4.80mm to 5mm thickglazingall withaluminum beading, glazing pin etc, or with oil putty in suaren exc .5 sqm in each pane |
| 32 | -do-- all as above but exc .5 sqm in each pane |
| 33 | S&FExtruded aluminium alloy handles, fabricated type., anodised in 150mm size |
| 34 | S&Fin repair Extruded aluminium alloy handles, fabricated type., anodised in 150 mm size |
| 35 | S&FSS butt hinges medium weight cold rolled stainless steel of size 100mm |
| 36 | S&F in repairs SS butt hinges medium weight cold rolled stainless steel of size 100 mm |
| 37 | S&Falumn anodized barrel tower bolt of extruded section & fixed of size 150mm |
| 38 | S&Fin repair alumn anodized barrel tower bolt of extruded section & fixed of size 150mm |
| 39 | S&Falumn anodized barrel tower bolt of extruded section & fixed of size 100mm |
| 40 | S&Fin repair alumn anodized barrel tower bolt of extruded section & fixed of size 100mm |
| 41 | S&F aluminium alloy wire mesh 0.45 mm nominal dia of wire and average width of aperture 1.4 mm fixed with aluminiumwire staples and beading /U sectionif requires complete all as specified and directed |
| 42 | S&F 140 mm overall length floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor all complete as specified and as directed by Engr-in-Charge. |
| 43 | S&F in repair 140 mm overall length floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor all complete as specified and as directed by Engr-in-Charge. |
| 44 | S & F in repairs aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperature 1.40mm and fixed with almn wire staples and rubber beading /U sectionif requires including taking down old windows and refixing in same position complete all as specified and directed |
| 45 | M&L for providing 25 mm thick soft rubber mat of approved colour with or without interlocking and fixed on existing floor using adhesive as recommended by manufacturer |
| 46 | S&F glass door assembly 12 mm thicktoughenedglassfor glass door,double shutter including SS pivot of floor door closer at top and bottom SS corner support SS handle 600 mm long fixed at both sides of both shutter andincluding all SS fittings and lock assemblyas required superior quality complete all as specified and directed by Engr-in-charge |
| 47 | Taking down aluminium sections and refixing in the same opening for fixing high density polymer extruded mesh including all necessary fitting fixtures etc(New aluminium sections shall be msrd and paid seperately) |
| 48 | S&F in repairs high density polymer extruded mesh coloured 2.0mm thick mesh and 32 mm average aperture for bird protection all as specified and directed |
| 49 | S&F in repair aluminium anodised DECO grill,DG-104 fixed with necessery U/F/H channel including taking down and refixing the window etc complete all as directed by Engr-in-charge. |
| 50 | S&F 10 mm thicktoughenedglass as in partition, doors and similar works including cutting to shape drilling holes requiredcomplete all as specified and directed by Engr-in-charge |
| 51 | S&F in repairs solar control film 50 mic reflective type sticked to glass panes icluding cleaning the glass as per instructions of manufacturers |
