Tender For Renovation Of C.R. building., B.Wall, App. Road, Augmentation Of Yard And Other Allied Civil Works At 33/11 Kv S/S Lalwadi And Datwas., 1 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.(B-1.31) 2 Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils (B-1.8) 3 Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. (A)1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size).(B-3.1.6) 4 (B) M15 grade Nominal Mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stoneaggregate 20mm nominal size)..(B-3.1.2) 5 Providing and laying ofpaver block as per IS 15658 : 2006 (Indian standard for precast concrete block for paving- specification) and IRC : SP:63-2004 (guidelines for the use of interlocking concrete block pavement)M-40,80mm thick to be used in medium- traffic ( Medium traffic is defined as a daily traffic of 150-450 commercial vehicles exceeding 30 KN laden weight, or an equivalent of 0.5 to 2.0 MSA for a design life of 20 years.) like city streets, small and medium market roads, low volume roads, utility cuts on arterial roads, etc.Category‘A’Category A Denated units to key into each other on four faces zigzagshape as per IRC SP 63:2004. + Add extra over item No. 11.38, A to C if reflective paver block, manufactured with wet cast vibration system in two layers is used.(A)(B-11.38.3)+(B-11.39) 6 Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in::Cement mortar 1 : 6 (1 cement : 6 coarse sand) (B-6.1.6) 7 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge. (B-14.2.1) 8 Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for:Columns, pillars, posts and struts etc.(B-4.10.3) 9 Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering.M20 grade Nominal Mix1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stoneaggregate 20mm nominal size). (B-3.2.1) 10 Brick masonry with F.P.S. bricks of class designation 75 infoundation and plinth with bricks Cement mortar 1 : 6 (1 cement : 6 coarse sand) (B-5.1.2) 11 Providing&fixingprecastcementconcretecoping1:2:4mix50mmthickcompleteas per specification :(B-3.8) 12 Plaster on new surface on walls in cement sand morter 1:6 including racking of joint etc. Complete fine finished (A) 20 mm thick (B-12.3.2) 13 (B) 12 mm thick (B-12.3.3) 14 (C) 25 mm thick (B-12.3.1) 15 Structural steel work riveted,bolted or welded in built up sections, trusses and framed work, including cutting, hoisting (height upto 10 m) , fixing in position and applying a priming coat of approved steel primer all complete:.(B-9.2) 16 Spray painting in approved shade and approved qualitywith Duco paint of required colour to give even shade with two or more coats by compressor including sand papering, NC putty filler coat etc complete in all respect as per design given by Engineeer incharge on new work.(B-12.65) 17 Repair of existing steel glazed doors, windows and ventilator, MS sheet door, garge doors, compound wall gates etc. by welding drilling complete include. Cost of welding rods and hire charge of welding meachine and TP etc complete.(B-13.23) 18 Painting with synthetic enamel paint of approved brand and manufacture togive an even shade : Two or more coats on new work(B-12.46.1) 19 (B)One or more coats on old work. (B-12.46.2) 20 Finishing walls with Acrylic Smooth exterior paint of required shade including all scaffolding.New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). (B-12.42) 21 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:Newwork(twoormorecoats)overandincludingscrappingandprimingcoatwithcement primer.(B-12.37.1) 22 Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete,New Plastered Surface (three or more coats) (B-12.22.1) 23 Providing and fixing M.S. sheet 1mm thicksingle leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint.(B-9.17) 24 Add extra for double leaf shutters. (B-9.17.1) 25 Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3mm thick water proofing membrane, black finished reinforced with non-woven polyester mattconsisting of a coat of bitumen primer for bitumen membran @ 0.40 Itr/sq.mt. by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ltr and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under Joint strength in longitudinal and transverse direction at 23°C as 650/450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D-5147. The laying of membrane shall be got done through the authorized applicator of the manufacturer of membrane.3 mm thick(B-15.12) 26 Providing & laying broken glazed titles on roof ( broken glazed tilesnot less than 9 Kg/Sqm) on top of hot bitumen @ 1.7 Kg/Sqm. (1.40 Kg ofVG-40 (30/40 )grade and 0.30 Kg/Sqm. OfVG-10 (80/100) grade) and joints filled with cement mortar 1 :2 (1 cement:2 marble dust mixed with water proofing compund all complete as per direction of Engineer-in-charge. (B-10.24) 27 Repair of rolling shutter with replacement of shutter spring incl. removal of old spring in the existing rolling shutter incld. Cost of new spring(B-13.26) 28 Repair of rolling shutter with using any material such as bend repair , tightening of spring,bolt and screw etc complete (B-13.27) 29 Lettering with black Japan paint of approved brand and manufacture. (B-12.62.2) 30 Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide . Extra if square,rectangular hollow tubelarsections are used or grill made by flats only. (B-9.8 + B-9.8.1) 31 Repair to damaged RCC slabs, beams and columns etc for strengthening with cement mortar 1 : 2 in following steps :- (I)Choping losse and cracked concrete to required depth, cleaning the exposed surface of steel and concrete with wire brush and sand papering , cleaning of concrete surface with water as necessary and getting dried. (II) Applying Epoxy primer on the exposed steel bars.(III)Applying Epoxy hardener and resin mix (as per manufectureds specification) on concrete and steel bars with brush.(IV) Speading dry cement mortar 1 : 2 mix over epoxy treated wet surface and allow it to dry for one day.(V) Plastering the surface with cement sand mortar 1 : 3 upto depth of 30mm complete.(VI) Cure the plastered surface for 15 days, All work including scaffolding etc. complete in all respect. .(B-13.29) 32 Providing and fixing welded mesh/expanded metal mesh in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. complete (excluding frame work) of size.Welded mesh 25 mmx 25 mm x 2.1 mm (B-9.38.3) 33 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement : 3 coarse sand ) including making joints with without grooves (thickness of joints except at sharp curve shall not to more than 5mm) including making drainage opening wherever required complete including painting etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineerin- charge)..(B-11.29) 34 Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead. (B-14.55) 35 Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.For area of each slab from 2001to 5000 Sqcm (B-11.19.2) 36 Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. (B-9.26) 37 Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure A: Commercial Veneer both side (B-8.13.2.1) 38 Extra for providing external lipping with 2ndclass teak wood battens 6 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) Over item no. 8.13.. (B-8.14) 39 Applying priming coat With ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood. (B-12.45.1) 40 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches by sandla/loi. (only for colour changing ).(B-12.35.7) 41 Renewing glass panes,with putty and nails wherever necessary.Float glass panes of thickness 4 mm (B-13.4.1) 42 Repair to stone masonary in cement sand mortar 1:6 with old and new stone.. (B-13.12) 43 Labour charges for repair to door / window without using any material such as applying randha (finishing) tightening of bolts & screw etc. (B-13.24) 44 Cleaning of sewer line of various sizes as per requirement at site of different sizes including 100mm,150mm & 225mm dia ofStoneware pipe as per direction of Engineer-in-Charge. (s/3.48) 45 P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor: Size 580x440mm. (S-1.2.2) 46 P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall :Size 550 mm x 400 mm (S/1.36.3) 47 P & F Looking Mirrors with P.V.C. frame of approved make as per direction of Engineer-in-charge : Size 500x400mm (S-1.45.1) 48 P & F Towel Rail or Ring of approved quality/make:C.P. brass Towel Rail elbow type with concealed screws size 450mm (Heavy duty).(S-1.47.1) 49 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1 metre spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall)(A) 15 mm nominal size. (S/2.37.1) 50 (B)25mm dia. Normial size.(S/2.37.3) 51 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement , trenching refilling & testing of joints complete as per direction of Engineer in Charge.(External work).(A) 15mm dia. Normial size.(S/2.39.1) 52 (B)25mm dia. Normial size.(S/2.39.3) 53 Making connection of G.I. distribution branch with G.I. main including all fitting. (A) up to 25mm dia (S/2.3.1) 54 P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make:(A) CP Brass bib cock 15mm nominal bore. (S/2.7.3) 55 (B) Long body 15mm nominal bore weight not less then 690 gm. (S/2.7.4) 56 P & F Ball Cock (IS :1703 Mark) with Rod& P.V.C. Ball complete :: Brass wt. Not less than 300 gm,15mm.(S-2.11.1) 57 P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. C.P. Inlet connection 15mm.Brass (IS : 8931 marked)(S 2.12.1) 58 P & F 15 mm. Dia Connection Pipe of approved quality/make :PVC pipe withC.P. Brass nuts upto length, 450mm(S-2.13.3) 59 P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make :(A) Gun metal15mm nominal bore (S/2.15.1) 60 (B) Gun metal25mm nominal bore (S/2.15.3) 61 Supply & fixing G.I. Union ISI marked in G.I. pipe line as required complete in all respect of size :(A) 15mm dia nominal bore (S/2.32.1) 62 (B) 25mm dia nominal bore (S/2.32.3) 63 P & F PVC Storage Tank ISI Marked (IS : 12701) indicating theBIS license No),of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design:(A)500 litre capacity. (S/2.26.3 ) 64 Providing & Laying C.C. 1:3:6 (Stone Agreegate 20mm nominal size) all around PVC Pipe including 7.5 cm thick bed concerte [Width & Height =Dia of Pipe in CM+15CM] excluding cost of Pipe & Excavation of trenches etc.(A)PVC pipe 110 mm dia(S/3.16.5.1) 65 P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant.(A)110 mm dia(S/3.16.3) 66 P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant:(A) Bend 87.5. 110mmdia(S/3.17.9/(II)) 67 (B) Bend 45. 110mmdia(S/3.17.8/(II)) 68 (C )Coupler (Soket) 110mmdia. (S/3.17.1/(II)) 69 (D)Pipe clip.110mm dia.(S/3.17.15/(ii)) 70 (E)VENT Cowel .110mm dia.(S/3.17.12/(ii)) 71 (F )PLAIN TEE 110mmdia. (S/3.17.3/(ii)) 72 Construction of manhole in all type of soil inner size 90 X 60 Cm. 300 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead.Depth up to 0.5 M (S/3.19.1) 73 Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). (B-7.12) 74 Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirmingto IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). (B-7.13) 75 Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m,10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr.Inside size 300 X 300 mm depth upto 0.5 MCement cover with frame..(S/3.21.1) 76 P & F Soap Dish or Tray of approved quality/make C.P. brass (S-1.52.1) 77 P&FFlushCock / FlushValve(IS :9758Mark)forWCofapproved quality make : Brass / GunmetalHalf-turnwt. 1 Kg.ofapprovedquality / make,25mmnominalbore.(S/2.14.9) 78 Providing and fixing bright finished Mortice lock of approved make Godrej or equivalent withpair ofCP handles for doors with necessary screws etc complete (Best make of approved quality) as per direction of Engineer-in-charge. (B-8.31)
