|
| 1 | Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. |
| 2 | 250 mm thick Brick work with 1st class bricks in cement mortar (1:6)(b) In superstructure, Ground Floor |
| 3 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (i) With 1:6 cement mortar(c) 15 mm thick plaster |
| 4 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface(ii) With 1:4 cement mortar (c) 10 mm thick plaster |
| 5 | Supplying & laying 3mm thick pre-fabricated plastomeric water proofing membrane conforming to EN 12311-1 & ASTMD 5147, manufactured with atactic poly propylene (APP) modified premium grade asphalt , specially reinforced with non-woven polyester core with polyester reinforcement @160 gms per sqm & both faces covered with thermo-fusible polyethylene film /MineraL on top face over a coat of primer @ 0.40 lit/sqm of manufacturer\"s specification on smooth,clean dry surface prepared wherever required.Lap joint shall be provided of 75 mm in longitudinal & 100 mm intransverse direction and fused using LPG/ Propane torch employing extra care ensuring full bondage, complete removal of entrapped air and sealing edges into grooves in appropriate manner as per direction of Engineer -in-charge all complete including materials,labour and applicable taxes. (Payment shall be made on the basis of finished surface area.).Membrane Property: Softening Point > 150 deg C, Cold Flexibility < -6 deg C, Tensile Strength, N/cm : 600 (longitudinal), 450 (transverse), Tearing Strength, N: 300 (longitudinal), 200 (transverse) |
| 6 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors….(B) Wall -With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.- Area of each tile upto 0.09 Sq.m- Other than Coloured decorative including white- In ground floor |
| 7 | Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately)(b) 40mm x 6 mm, 200mm length |
| 8 | Iron Butt hinges of approved quality fitted and fixed with steel screws, with ISI mark.(ii) 100mm x 58mm x 1.90mm |
| 9 | Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting.(b) 250mm long. |
| 10 | Iron socket bolt of approved quality fitted and fixed completed) 225mm long x 10mm dia bolt |
| 11 | Steel body foot-door holder. |
| 12 | Anodised aluminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete :(a) With continuous plate base (Hexagonal / Round rod)(iv) 125mm grip x 10mm dia rod |
| 13 | Supplying and fixing Frames for Lead Lined FD120 Fire Rated Door System as per the IS: 3614-1992 Part-II and BS:476-1987 Part - 20 & 22 with 1st ClassMalayasian Hardwood densified and pressure treated with fire retardent chemicals in vacuam inpregnation vessels under 160 PSI pressure as pe IS:401and kiln seasoned to moisture below 15% as per IS:1141 of section 120mm x 70 mm and shielding the frame with 3 mm thick & 45 mm wide 2 (two) protective lead covering conforming to ASTM B749-03 for reducing the radiation level to 2 mrem in 1 hour as stipulated by code of Federal Regulation (CFR), placed parallel each other staggeredly with an lateral over lap of 20mm at the region of discontinuity and fixed inside along the the frame, spray coated with 2 coats of enamel paint after 1 coat of white wood primer of minimum 200 micron,with single row of Brush- Type intumescent strip (equivalent to ASTROFLAME ) of size 10 mm x 4 mm affixed in the slit of the Frame for fire and smoke sealing, etc. including all incidental charges complete in all respect as per direction ofEngineer-in-Charge. |
| 14 | Supplying & fitting of 55mm thick asbestos free - fire, heat and smoke resistant composite Fire check Door Shutter complying with fire performance-FD120 asper IS:3614 (part -II)-comprising of 2x8 mm Calcium Silicate boards over Chemically treated (with Fire retardant chemicals in pressure impregnationvessels under 160 psi pressure as per IS:401 and kiln seasoned to moisture below 15% as per IS:1141) internal timber (Malaysian Hard Wood, densified to810 kg/cum) frame work of 100 mm x 32 mm with 32mm thick infill of ceramic fiber (density 128Kg/cum), vermaculite mix faced with 3 mm Fire retardant High Density fire board on outerside & similar one over 3 mm thick protective lead covering conforming to ASTM B749-03 for reducing the radiation level to 2 mrem in 1 hour as stipulated by code of Federal Regulation (CFR), internally lipped with hardwood beading, and pasted in Hydraulic Press under 25 MPa, spray coated with 2 coats of in-tumescent paint of minimum 300 micron, and with single row of Brush- Type intumescent strip of size 10 mm x 4 mm affixed on peripheral slit on all edges of shutter except bottom for fire and smokesealing, without any external lipping including fitting, fixing shutters in position but excluding the cost of hinges & other fittings as per direction of Engineer-in-Charge complete in all respect in Ground Floor |
| 15 | Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer\"s specification) including cleaning and smoothning of surface. Two Coats |
| 16 | Installation , testing & commissioning of 1.8 ton/2 ton capacity of split type AC machine both indoor & outdoor unit with necessary fixing on wall ( Indoor unit & outdoor unit ) as per direction of EIC by providing of 40x40x5 mm MS angle iron frame with necessary anchoring facilty on one side for necessary support on outer wall / making pedestal by angle & flat with necessaery welding each other etc. & Making hole for providing holding with outdoor unit by proper gauge Gl nut bolt & washer with necessary painting by synthetic enamel paint two coat of one after another over one coat of RO primer or Providing of ISI marked bracket provide on wall by necessary providing of 100 mm MS / Gi Fastner arrangwement not less than 6 ( six ) no for each unit , with making hole on wall with making necessary slopping maintain & mending good damages as per direction of EIC . |
| 17 | Supply and fixing of HVAC grade copper pipe of following sizes for liquid and Gas line between ODU and IDU. [Make:- Ryoku/Nippon]5/8\" (Gas Line) |
| 18 | 1/4\" (Liquid Line) 9 mm thickness |
| 19 | Supplying & Fixing of insulation properly wrapped with tape (Polyethylene Foam/Nitryle Rubber Foam) of following thickness for liquid and Gas line (Make:-Armacell/K-Cell/Supreme)5/8\" (Gas Line) 9 mm thickness |
| 20 | 1/4\" (Liquid Line) 9 mm thickness |
| 21 | Supply and fixing of 3 core 2.5 sq.mm PVC insulated unsheathed copper flexible power cable for inter connection between IDU & ODU. (Make - Havells/Gloster/RR/KEI] |
| 22 | Supply and fixing of 18 mm dia PVC flexible pipe with nylon reinforced including jointing materials for drainage of water. (Make - Supreme/Oriplast) |
| 23 | GST 18% |
| 24 | cess 1% |
