|
| 1 | Excavating in post holes in any type of soil ( or similar holes ) each n exc 0.5 cum getting out, returining, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm , watering, and removing surplus soil to a distance n exc 50 mtr. complete all as specified and as directed . |
| 2 | M&L plain cement concrete in foundation type C 2, 1:3:6 ( 40 mm grade stone aggregate) as in filling and mass concrete Complete all as specified and as directed. |
| 3 | S&F Rolled mild steel in plates, girder,channels square cut or notched (ordinary and colour sunk) forming holes, without any attachment conf to Fe 410-W (Gde E-250) quality \"A\". complete all as specified and as directed . |
| 4 | S&F structural steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confrming to IS 1161-1979 grade St-240 complete all as specified and as directed. |
| 5 | M&L for two coats of synthetic enamel paint over a coat of red oxide or zinc chromate primer including preparation of new steel or iron surfaces exc 10 cm width or girth, complete all as specified and directed. |
| 6 | S&F Pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering /cladding to wall fixed with self tapping screws complete all as specified and directed. |
| 7 | Surface dressing not exc 15 cm deep and getting out in soft/ loose soil complete all as specified. |
| 8 | M&L for Hardcore(Broken boulder) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed. |
| 9 | M & L for 75 mm thick PCC (1:4:8) type D2, using 40 mm graded stone aggregate as in sub base surfice finished even and rough to receive floor topping complete all as specified and as directed . |
| 10 | M & L for machine made Rubber moulded precast concrete interlocking paver block (coloured), Glossy finish pre polished of any shape and size with white cement and pigment confirming to IS 15658-2006 of 60 mm thickness M-35 Gradeand filleting to edges with cement concrete work complete all as specified and directed. |
| 11 | Removing excavated material n exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and as directed . |
| 12 | Taking down the complete old rolling shutter including all fittings and area exceeding 9.00 Sqm in each complete all as specified and as directed. |
| 13 | S & F collapsible steel gate ,top hung,consisting of channel pickets ,pivoted flat bars,top and bottom runners ,brass locking handles etc,as specified,erected in position and securing runners with holdfast and brackets complete all as specified and as directed. |
| 14 | S&F Providing and fixing Powder coated aluminium section (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size complete all as specified & directed., Note : Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, |
| 15 | S&F anodised aluminum door shutters, aluminium section weighing not less than 0.55 Kg/ Sqm including necessary jointing cleats, glazing clips, ruber neoprene packing, SS handles 02 Nos in each door, hinges, anodised aluminium snap beading C.P brass/SS screws etc. complete all as specified and directed. |
| 16 | M&L for 12mm thick clear toughened glass fixed to door and window as directed by Engr-in-Charge including necessary wooden beadings, nails, screw, cleats complete all as specified and directed. |
| 17 | M&L for 6.3mm thick Sheet tinted glass, selected quality, in squares exc 0.5 sq. m in each pane of approved colour in doors, partition fixed with and including rubber beading complete all as specified & directed. |
| 18 | M&L double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed . |
| 19 | M&L for wall panelling on existing wall surface consisting 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and drawing to be fixed on wall by self tapping screw of size 19mm x 6mm after puttin rawal plugs. The edge and periphery finally to be covered by extruded PVC corner angles beading/fillet complete all as specified and as directed. |
| 20 | S & F 5 mm thick PVC sheet fillet /beading of width 35 mm for wall panelling inclusive of fixing on wall to make PVC frame as per specification and drawing complete all as specified and as directed. |
| 21 | M&L machine cut Granite stone slab 18 to 20 mm thick as in walls,floor,steps, pillars,window cills, parapet tops,and like and incl 10mm thick (avg thickness) cement mortar 1:4 screeding and setting coat in cement morter (1:2) 3mm thick, with araldite adhesives set and jointed with white cement slurry mixed with pigment to match the shade of slab incl cutting, waste, rubbing and polishingetc complete all as specified and as directed .Note:- (i) The rate of granite stone shall be deemed to incl for full rounded off corner/edges incl all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and granite polishing to achive the desired granite finish complete all as specified and directed. |
| 22 | Providing and fixing of false ceiling withpowder coated exposed G.I. grid suspension system (E-Grid T-2430 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200 mm c/c) consisting of Main Runner 3600 mm long, Cross Tee 1200mm/600mm long and Wall Angle. The Wall Angle shall be fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300 mm c/c. The Main Runners to be placed @ 1200mm, The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of 1200mm x 600mm. Additional Cross Tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600mm x 600mm. Grid of module size 600mm x 600mm shall be supported by 6 mm dia G.I. wire from purlins/soffit. 4mm thick High Pressure Steam Cured Everest Non Asbestos Fibre Cement Designer Ceiling Board (Density>1200 Kg/m3, Modulus of Rupture(M.O.R)-15.85 MPa, Thermal Conductivity(K)-0.0872 W/mK) of size 595mm x 595mm, confirming IS 14862 & Type B Category III of ISO 8336:1993, (Reaction to fire-A2-s1-d0) tested as per EN13501 Part-I & BS-476 Part 4,5,6&7, should be placed in the Grid module to form a False Ceiling, complete as per the drawing & directions of Engineer-in-Charge. |
| 23 | M&L for Fly ash bricks, straight or curved on plan exc. 6m mean radius built in CM 1:6 complete all as specified and directed. |
| 24 | M&L for rendering 15mm thick on concrete block/ brick or concrete surfaces in cement mortar 1:6 finished surfaces even and smooth without using extra cement, complete all as specified and directed. |
| 25 | M & L for preparation of new wall surfaces including two coats of oil bound distemper over a coat of approved primer and 2mm thick putty complete all as specified and as directed. |
| 26 | M&L for 1mm thick stainless steel letter in English 300mm high fixed on any surface including necessary scaffolding etc complete all as specified by Engr-in-Charge. Width of each letter should be in proportionate with height of letter complete all as specified and directed. |
| 27 | S& F in repairs 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. |
| 28 | S&F in repairs 150 mm long aluminium, anodised, or matt finished barrel tower bolts of extruded section complete all as specified and directed. |
| 29 | S&F in repairs 150 mm size extruded aluminium alloy bow handles, fabricated type with plate, matt or anodised finish complete all as specified and directed. |
| 30 | S&F in repairsfloor door stopper 140mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 31 | S&F in repairs 60 cm long SS tubular towel rail 20-mm dia complete all as specified and directed. |
| 32 | S&F in repairs 10 liters capacity PVC low level flushing cisternwith ISI marked body, complete all as specified and directed. |
| 33 | S&F in repairs 100mm dia CP grating for nahani traps with or without hole for waste pipe complete all as specified and directed. |
| 34 | S&F in repairs stainless steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanized wire staples complete incl fillets for securing wiremesh complete all as specified and as directed . |
| 35 | S&F in repairs 15 mm bore, 45 cm long PVC connecting pipe fitted with brass unions to connect iron pipe to PVC pipe on both ends complete all as specified and directed. |
| 36 | S&F in repairs 15 mm bore stop valves, cast copper alloy, chromium plated, with long shank and cup (concealed type) fancy type screwed down, high pressure, with crown head, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 37 | S & F chromium plated health faucet (hand jet) 15mm bore with fittings, and including two way bib tap and accessories complete all as specified and directed. |
| 38 | S&F in repairs brass chromium plated shower rose of 125 mm size with swivel joint including fixing to steel pipe or union complete all as specified and directed. |
| 39 | S&F in repairsfor pillar taps 15 mm, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot\" or `Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. |
| 40 | S&F in repairs 15 mm bore bib taps, fancy type cast copper ally chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 41 | S&F 600 mm x450 mm beveiled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and washers as in repairs complete all as specified and directed. |
| 42 | S&F in repair 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete, complete all as specified and directed. |
| 43 | S&F in repairs 15 mm bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. |
| 44 | Taking down cement plaster from brick /concrete/ stone surfaces including racking out joint , hacking for key and scrubing down with water etc complete all as specified and as directed . |
| 45 | M&L for rendering 10 mm thick on concrete surfacesor surfaces other than fair face of brick work in CM 1:6finishing surfaces even and smooth without using extra cement complete all as specified and as directed . |
| 46 | M&L for preparation ofold/ newly plastered surface of walls over 10 cm width or girth over a coat of approved primer and applying two coats of oil emulsion distemper (tint as approved by GE) over a coat of primerand2mm thick wall care putty complete all as specified and directed. |
| 47 | M&L for preparation of plastered or unplastered old decorated surfaces of ceiling etc. incl pillasters and cornices etc. incl brooming down of steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and grease spot, washing etc. and applying one coat of white lime wash complete all as specified & directed. |
| 48 | M&L for preparation of old painted surfaces of wood and wood based surfaces of anydescription over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 49 | M&L for Preparation of old painted surfaces of steel & iron of any description over 10cm width or girth and applying one coat of synthetic enamel paint (1st quality) etc complete all as specified and directed. |
| 50 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm each and removing from site complete all as specified and directed. |
| 51 | S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail.Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, and fixing in the frame at site complete all as specified and directed. |
| 52 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, supplying & fixing in opening complete all as specified and directed. |
| 53 | S&F 40 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type both sides (ISI marked) all with 6 mm thick teak wood edging all round complete all as specified and directed. |
| 54 | M&L for preparation of new wooden surfacesof any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 55 | S&F stainless steel butt hinges,of size 100 mm complete all as specified and directed. |
| 56 | S&F 150 mm long aluminium, anodized, barrel tower bolts of extruded section and fixed complete all as specified and directed. |
| 57 | S&Fextruded aluminium alloy handles, fabricated type, anodized of size 150 mm complete all as specified and directed. |
| 58 | S&F 300mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia and including minimum of6 bolts and nuts, four on bolt plate and two on staple complete all as specified & directed. |
| 59 | Dismantling floor or wall tiling incl cement mortar bedding ( but not backing) removing serveaceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 60 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors/ skirtingetc.and joineted neat in cement slurry and pointed in white or colour cement to match over & including 15 mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 61 | S&F glazed ceramic tiles coloured 350 x 250mm/450 x 350mm 7 mm thick in wall/dado etc, set & jointedin neat cement slurry & pointed in white or coloured cement to match inluding rendering 15 mm thick in CM 1:6 on stone masonry surfaces or surfaces other than fair face of brick work/ concrete surfaces complete all as specified and directed. |
| 62 | S&F in repairs, vitreous China wash down water closet pan, (pedestal pattern), white, with and including plastic water closet seat, white, closed pattern with flat bottom, andcover and mild steel chromium plated or aluminised hinging device etc complete all as specified and directed. |
| 63 | S&F in repairs plastic water closet seat,white closed pattern, solid type with flat bottom, and cover and mild steel chromium plated hinging device complete all as specified and directed. |
| 64 | S&F in repair for vitreous China wash basin, white, flat back, size 550x450mm including necessary brackets,cp couplings, pvc waste pipes etc complete all as specified and directed. |
| 65 | S&F in repair steel water tubes, 20mm bore medium grade, galvanized with all fittings and fixed complete to walls, ceiling or laid in floor, complete including taking up or down steel tubing and connections or removal to store complete all as specified and as directed . |
