Tender For Pmgsy-Iii- 2024-25 (Batch-1) Package No. Kr03112bmlamala -Muslimpallipady Bridge In Azhutha Block, Idukki District
Tender Value
4.66 Crore
Estimated cost
Bid Submission
09 Dec 2024
0 days left
EMD
1 Lakhs
Bank guarantee accepted
Document Fee
8270
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Thiruvananthapuram → Kerala
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For PMGSY-III- 2024-25 (Batch-1) Package No. KR03112Bmlamala -muslimpallipady bridge in Azhutha Block, Idukki District
BOQ
| Sl. No. | Item Description |
| 1 | CLEARING AND SCARIFYING |
| 2 | 2.5.1. B Dismantling of structures- Dismantling existing structures like culverts, bridges, retaining walls and other structures comprising of masonry, cement concrete, woodwork, steelwork, including T&P and scaffolding whereever necessary, sorting the dismantled material, disposal of unserviceable and stacking serviceable material with all lift and lead of 1000m as per technical specification Clause 202.1 -Cement Concrete(PCC) - By Mannual Means |
| 3 | 2.5.2 B Dismantling of structures- Dismantling existing structures like culverts, bridges, retaining walls and other structures comprising of masonry, cement concrete, woodwork, steelwork, including T&P and scaffolding whereever necessary, sorting the dismantled material, disposal of unserviceable and stacking serviceable material with all lift and lead of 1000m as per technical specification Clause 202.1 -Reinforced Cement Concrete (RCC) - By Mechanical Means |
| 4 | 3.8.2 Excavation in Ordinary Rock with Dozerwith lead upto 100m- Excavation for roadwork in ordinary rock by deploying a Dozer, D-50 including cutting and pushing the cut earth to the site of embankment upto a distance of 100m (average lead 50m) including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections a as per technical specification Clause 302.3.5 |
| 5 | 3.15.1Compacting Original Ground Supporting Subgrade- Loosening of the ground upto a level of 300mm below the subgrade level, watered, graded and compacted in leyers to meet requirement given in Table 300.1 and 300.2 for subgrade coonstruction as per technical specification Clause 303.5.2 |
| 6 | 3.14Construction of Subgrade and Earthen Shoulder - Construction of of subgrade and earthen shoulders with approved material obtained from private borrow pits with all leads and lifts transporting to site, spreading, grading to required slope andcompacting to meet requirement of Table300.2with lead upto 1000m as per technical specification Clause 303.1. |
| 7 | 3.19.1 Surface Drains in Soil- Construction of unlined surface drains of average cross sectional area 0.40sqm in soil to specified lines, grades, levels and dimensions. Excavated material to be used in embankment with a lift upto 3.0m and lead of 50m as per technical specification Clause 307 - By Mannuall Means |
| 8 | 4.1.A.1Granular Sub-base with Well Graded Material (Table 400.1)By Mix in Place MethodConstruction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavatorat OMC, and compacting with smoothwheelroller to achieve thedesired density, complete as per Technical Specification Clause 401. (For Grading I Material) |
| 9 | 4.9Wet Mix macadam -providing, laying, spreading and compacting stone aggregates of specified sizes to wet mixmacadam at OMC in mechanical mixer (pug mill), carriage of mixed material by tipper to site,layingin uniform thickness in sub-base / base course on a well prepared sub-base and compactingwith smooththree wheel 80-100 kN static roller to achievethe desired density including lighting, barricading and maintenance of diversion etc as per table 400.11 & 400.12 and as per technical specification Clause 406 |
| 10 | OD5.1.1pbPrime Coat - Low porosity-providing and applying primer coat with bitumen emulsion (Packed SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at a rate of 0.70 - 1.00 kg/sqm using mechanical means as per technical specification clause 502 |
| 11 | 5.2.3 Tack Coat - Providing and applying tack coat with bitumen emulsion (Packed RS-1) using emulsion distributorat a rate of 0.25 - 0.30 kg/sqmon the prepared granular surface treated with primer &cleaned with Hydraulic broom as per technical specification clause 503 |
| 12 | 5.9.1.520mm thick open graded premix carpet using bituminous binder S 65 Packed - Providing, laying and rolling of open graded premix carpet of 20mm thickness composed of 13.2mm to 5.6mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100kn roller, finished to required level and grades to be followed by seal coat either Type A or Type B or Type Cas per technical specification clause 508 -by Mannual means |
| 13 | 5.12.3.5 Seal Coat - Mannual Means - Type C - Providing andlaying seal coat sealing the voids in bituminous surface laid to the specified levels, levels and cross fall using Type A, Type B and Type C as per technical specification clause 510- UsingBitumen S 65 Packed |
| 14 | Traffic signs,markings |
| 15 | 10.2.A.2.2 Traffic Signs- Retro-reflective Traffic Signs - Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign asper IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 1.5 mm thick supported on GI pipe 50 mm dia firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 1701- 600mm equilateral triangle board |
| 16 | 10.2.A.2.4Traffic Signs- Retro-reflective Traffic Signs - Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign asper IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 1.5 mm thick supported on GI pipe 50 mm dia firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 1701- 800mm x 600mm rectangular board |
| 17 | 10.2.A.2.3 Traffic Signs- Retro-reflective Traffic Signs - Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign asper IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 1.5 mm thick supported on GI pipe 50 mm dia firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 1701- 600mm circular board |
| 18 | 10.3.A.2Traffic Signs- Direction and place identification sign upto 0.90 sqm size board - Retro - reflective Traffic Signs -Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on 2 inch dia GI Pipe firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 x 450 x 600 mm, 600 mm below ground level as per approveddrawing and Tehnical Specification Clause 1701. |
| 19 | 10.5 Painting Two coats on New Concrete Surfaces - Painting two coats icluding primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and technical Specification |
| 20 | Mod 8.13 -MoRTHPainting Lines, dashes, Arrows etc on Road in two coats on new work - Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads on Bituminous Surface @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes. Over 10 cm in width. |
| 21 | 10.16 Providing and Fixing \"Logo\" of PMGSY Project - Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 |
| 22 | 10.16 OD Providing and Fixing typical PMGSY citizens information board as per MoRD specifications and drawings-Two vertical76.1mm outer diameter MS sheet tube posts of 3.60mm thickness (medium class)duly embedded in cement concrete M-15 grade blocks of 600mm x 600mm x750mm, 600mm below ground level with two horizontalM S Sheet Tubesof 1000mm length to make the frame of board, four horizontals and two verticalswith M S Sheet rectamngular Tube 50x25x2mm to make the frame to fix the board as per drawing, two M S Sheet 2.00 mm thick boards of size 900x750mm strengthened by 25mmx5mm MS flat iron includingpainting with stove enameled paint on both sides as per MoRD specifications. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 |
| 23 | Protection work |
| 24 | 11.1.1.1 Excavation for Structures -Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material : Ordinary soil : Upto 3 m depth |
| 25 | 16.95Providing & making Gabion structure with Mechanically Woven Double TwistedHexagonal Shaped Wire mesh Gabion Boxes as per IS 16014:2012,MORTH Clause2500, of required size, Mesh Type 10x12(D=100 mm with tolerance of ? 2%) Zinic+PVCcoated, Mesh wire diameter2.7/3.7mm, mechanically edged/selvedged with partitionsat every 1m interval and shall have minimum 10 numbers of openings per meter ofmesh perpendicular to twist, tying with lacing wire of diameter 2.2/3.2mm(ID/OD),supplied @3% by weight of Gabion boxes, filled with boulders with least dimensionof 200 mm, as per drawing, all complete as per directions of Engineer-in-charge. |
| 26 | Bridge works |
| 27 | OD. 60.1.1 RING BUND Type - 1 - Putting up of ring bund as per approved shape 2.50 m bottom width, 1.00 m top width and average height of 2.00 m using empty gunny bag/ Polythene bags filled with earth placed in 2 rows at 0.6m apart and filled in between with puddle clay to form bund including labour charges for dismantling the bund after completion of the work etc complete. |
| 28 | OD.60.2.2.Bailing out water Using 5HP Pump- Bailing out water with 5HP engine and pump set including conveyance to site and erection,cost of fuel, lubrication oil and other stores, pay of staff etc complete |
| 29 | OD 60.5.3 DOWEL BARS - Supplying and providing MS dowel bars of size 25mm dia 2.0 m long (1.0 m in rock and 1.0 m in concrete) including drilling holes of 30mm dia and filling the gap with cement grout (0.50kg/Each) etc complete with epoxy paint. |
| 30 | 11.1.2Excavation for Structures -Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material : Ordinary Rock : Upto 3 m depth |
| 31 | 11.1.4 Excavation for Structures -Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material : Hard Rock ( Blasting Prohibited) : Upto 3 m depth including 1.5m depth in hard rock |
| 32 | PCC Grade M 30 - Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications |
| 33 | 11.4.5 Modified RCC Grade M30 - Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203- |
| 34 | 11.8 Supplying, fitting and placing TMT bar reinforcement in foundation - complete as per drawings and technical specifications Clauses 1000 and 1202 |
| 35 | 12.5.6 modified RCC Grade M 30 - Providing concrete for plain/reinforced concrete in substructure complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203-above 5.00mtr height |
| 36 | 12.7 Supplying, fitting and placing TMT bar reinforcement in substructure - complete as per drawings and technical specifications Clauses 1002, 1005,1010 and 1202 |
| 37 | 13.1.3 RCC Grade M 30 - Providingand laying reinforced cement concrete in superstructure complete as per drawings and technical specifications Clause 800, 1205.4 and 1205.5 -Above 5.00m upto 10.00mtr Height |
| 38 | 13.3.Supplying, fitting and placing TMT bar reinforcement in superstructure - complete as per drawings and technical specifications Clauses 1002, 1010 and 1202 |
| 39 | O D RCC Grade M 45 - Providingand laying reinforced cement concrete in superstructure complete as per drawings and technical specifications Clause 800, 1205.4 and 1205.5 -Above 5.00m upto 10.00mtr Height |
| 40 | 13.14MoRTHSupplying, fitting and fixing in position true to line and level elastomeric bearing conforming to IRC: 83 (Part-II) section IX and clause 2005 of MoRTH specifications complete including all accessories as per drawing and Technical Specifications. |
| 41 | OD 60.6 PVC WHEEP HOLES - Providing weep holes using 75mm dia PVC pipes 4 kg/sq cm including cost of material , labour charges etc. complete |
| 42 | O D High tensile steel wires/strands including all accessories for stressing, stressing operations and grouting complete as per drawing and Technical Specifications |
| 43 | 11.4.3.1 Modified PCC Grade M 20 - Providing concrete for plain/reinforced concrete for wearing coat complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203- Nominal mix 1:2:4 |
| 44 | Load test |
| 45 | OD Load Testing over Deck slab Observed Data based on Required Loading as specified and conforming to IRC : SP51 |
AI Tender Summary
Tender Timeline
Nov 30, 2024
11:30 IST
Tender Published
Tender notice published.
CompletedDec 09, 2024
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedDec 13, 2024
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender