|
| 1 | Brick masonary in foundation and plinth with. bricks of class designation 75 in :Cement mortar 1 : 6 (1 cement : 6 coarse sand) |
| 2 | Add extra over item no 5.1 for brick work in super structure up to third storey |
| 3 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick |
| 4 | 6 mm thick cement plaster to ceiling of mix1:3 (1cement : 3-fine sand) |
| 5 | Providing and fixing glazing in aluminium door, window ,ventilator shutters and partitions etc. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Cost of aluminium snap beading shall be paid in basicitem.)With tinted glass panes of 5.0 mm thickness ( weight not less than 13.75 kg/sqm) |
| 6 | S&f fixed wire gauge of stainless steel of 14 mesh x 24 gauge to the aluminium window by Aluminium beading 20x3mm with suitable screws not exceeding 150mm distance at all heights with all lead and lift with scafolding. |
| 7 | Providing and fixing pressed steel door frames confirming to IS 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applyinga coat of approved steel primer after pre-treatment of the surface including filling with CC 1:2:4(M15 grade) complete as directed by Engineer-in-charge :Profile B |
| 8 | Profile C |
| 9 | Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesinin glue both sides with approved steel fittings complete as per annexure \"A\":Decorative teak Veneer both side 35 mm thick . |
| 10 | Providing and fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joint mitred weldedand grinded including hold fast of steel lugs 13mm x 3mm and 15 Cm long embedded in C Cblock 15 x 10 x 10 Cm of 1:3:6 nominal concrete and including fixing of pivoted hinges of superior quality, window shutters made out of 50 x 25.0 mm hollow steel section 15 mm paitam of 18 gauge thickness, joint mitred and grinded including 10mm x 10mm square bars welded to framefor paitam fixing float glass 4mm thickpanes with glazing clips and metal sash putty andfixing of shutters frames peg stay, U shape handle 100 mm long, tower bolts 100 mm long of steel powder coated superior quality including fixing and jointing with frame hinges priming coat with steel primer complete in all respect as per direction of Engineer-in –chargeWindows fixed |
| 11 | Window openable. |
| 12 | Providing 5mm thick plain glass instead of 4mm thickplain glass |
| 13 | Providing and fixing Square bars or other flat welded to window, ventilatiors etc. |
| 14 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. of jhansi ( Red /Choclate Colour ) Above 3601 cm2 |
| 15 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). Category -I Kajariya, Jhonson, Somani make etc. |
| 16 | Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirmingto IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4).Category -I Kajariya, Jhonson, Somani make etc. |
| 17 | Add extra over item no 7.6.1 & 7.6.2 for using 400x400 size Mat finish tile in place of 300x300 mm size |
| 18 | Add extra over item no 7.6.1 & 7.6.2 for using coloured dark shade tiles instead of white /ivory /grey /light green / sky blue / light brown and other light shade colour |
| 19 | P & F 1st qualityVitrified Porcelain Polished tiles on floor, skirting and steps etc.in different sizes (thickness to be specified by manufactuer) with water absortion less than 0.08% and conforming to IS 15622 of approved make in all colour and shade,laid with 20 mm thick CM 1 : 4 including grounting the joints with white cement and matching pigment etc complete. |
| 20 | Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete 30 mm thick slabarea upto 2001to 5000 Sqcm |
| 21 | Extra for providing edge moulding to 15-18mm thick marble/ Granite/Kota stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.For Granite work. |
| 22 | Random rubble dry stone Kharanja under floor. |
| 23 | Supply & fixing of stainless steel pipe railing for ramp railing height 90 cmwith 40 mm dia stainless steel pipe with 18 gauge with drop (vertical post ) at 90 cm C/C and intermidiate horizontel pipe with suitable height of same size and gauge with coupling grinding and polishing & fix of master piecesas par required point as per approved desing of engineer-incharge |
| 24 | Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth completeNew Plastered surface (three or more coat) |
| 25 | Applying one coat of Cement primer of approved brand and manufacture on wall surface including all scaffolding: |
| 26 | Painting with synthetic enamel paint of approved brand and manufacture togive an even shade :Two or more coats on new work |
| 27 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding:Two or more coats on new work including prepartion of basewith primer, putty, lippy etc complete in all respect. |
| 28 | Decorative plaster workwith spectrum textured coating asper approved colour and shade complete as per manufacturingspecifications Trowel finish ( 1 to 1.5 mm thick ) |
| 29 | P/L glazed tiles pieces for roof treatment having colour and shade as approved by engineer in charge over 20mm thick under layer of cement mortarmix 1:4 with application of cwmwnt slurry incid. Finishing of joints with white cement and pigment mayching the shade curing etc. complete in all respect. |
| 30 | Grading roof for water proofing treatment withwater proffing compoundCement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 31 | Making khurras 450 x 450mm with average minimum thickness 50mmcement concrete 1 : 2:4 over P.V.C. Sheet 1 Mtr. x 1 Mtr. x 40micron finished with 12mm cement plaster 1 : 3 and onecoat of neat cement, rounding edges and making and finishing the out let complete. |
| 32 | P/F expansion joints boaed for building RCC column beam, wall , slab of polyethylene foam of density 30 ton35 kg/m three of armour board. |
| 33 | P/F in position aluminium plate as per design for expansion joints. |
| 34 | Providing & filling in position bitumen mix filer of proportion 80 kg of hot bitumen1 kg of cement and 0.25 cubic metre of course sand for expansion joints. |
| 35 | P/F aluminum sheet 2.00 mm thick and 150 mm wide cver expansion joints with fixing rawl plug and aluminum screws as per design to matchthe colour shade of the distemperor wall treatment. |
| 36 | P & F European type white glazed vitreous china 1st quality W.C pan (IS : 2556 Mark) with P or S trap including cutting and making good the wall and floor |
| 37 | P & F water closet Seat Covers with brass hinges complete :grade -I Black EWC |
| 38 | P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete.Flat Back (large) or half stall size 610x400x80mm. |
| 39 | P&F Marble Urinal Partition slab both sides polished of approved design cut from marble size 900x600mm.Makrana `Adanga` or Raj Nagar 1St Quality White or Andhi Indo-Italian marble. |
| 40 | P & F Low level Flushing Cistern of 10 litres capacity (IS : 2556mark). Of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS: 1703 mark) complete including cutting and making good the wall: |
| 41 | P & F C.P. brass Urinal Spreader for stall urinal of approved make. |
| 42 | P & F WVC wash basin (1st quality, I.S. : 2556 Mark) of approved make with C.I. brackets duly painted, 1 No. 15 mm C.P. Pillar cock (IS : 8934 Mark) & 32 mm C.P. brass waste coupling of approved make,25 mm G.I. waste pipe complete including cutting & making good the wall.: Size 630 mm x 400 mm |
| 43 | P & F Bottle Trap of approved make :C.P Brass 32 mm |
| 44 | P & F Bevelled edge Mirror/mirror with teak wood lipping around of special glass of approved make as per direction of Engineer-in-charge complete with 6mm thick commercial ply base fixed to wooden screws & washers. |
| 45 | P & F Towel Rail or Ring of approved quality/make: C.P. brass Towel Rail elbow type with concealed screws size 600 mm (Heavy duty). |
| 46 | C.P. Brass Towel Ring revolving type |
| 47 | P & F Grating of approved quality/make: Stainless Steel Sheet size 125mm dia. |
| 48 | P & F Liquid Soap Container with brackets complete of approved make:C.P. brass |
| 49 | P & F Toilet Paper Holder with rod of approved quality/make:C.P. brass |
| 50 | P & F Soap Dish or Tray of approved quality/make C.P. brass heavy and superior quality. |
| 51 | P & F Jet spray for water closet with C.P. Copper Tube flange of approved make. |
| 52 | P & F G.I. pipes (Internal Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors:15mm dia nominal bore \"NBB\" Class |
| 53 | 25mm dia nominal bore\"NB\"B\" Class |
| 54 | Concealed pipe in wall incid. With anticorrosive bitumen paint 15 mm dia NBB class |
| 55 | P & F G.I. pipes (External Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors:15mm dia nominal bore \"NBB\" Class |
| 56 | 25mm dia nominal boreNBB class |
| 57 | P & F Pilllar Cocks (IS :8931 : 1993 Mark) of superior quality and approved make C.P. Pillar cock, Swan-neck with casted spout, 15mm nominalbore. |
| 58 | P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make:(-do-) Long body, 15mm nominal bore weight not less than 690 gm |
| 59 | P & F Ball Cock (IS :1703 Mark) with Rod& P.V.C. Ball complete :Brass wt. Not less than 300 gm,15mm. |
| 60 | P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make :Gun-metal 15mm nominal bore. |
| 61 | (-do-) 25mm nominal bore. |
| 62 | P & F PVC Storage Tank (IS : 12701marked indicating theBIS license No),of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 500 litres capacity. |
| 63 | Hoisting Charges for each floor :500 litres capacity. |
| 64 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /make including joining the pipe withsolvent cement rubber ring and lubricant 75 mm dia |
| 65 | 110 mm dia |
| 66 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approvedquality /make including joining the pipe with solvent cementrubber ring and lubricant:Coupler (socket) 75 mm dia |
| 67 | 110 mm dia |
| 68 | Reducer 110 X 75 mm 75mm dia |
| 69 | 110 mm dia |
| 70 | Plain tee 75 mm dia |
| 71 | 110 mm dia |
| 72 | Door tee 75 mm dia |
| 73 | 110 mm dia |
| 74 | Bend 45 75mm dia |
| 75 | 110 mm dia |
| 76 | Bend 87.5 75mm dia |
| 77 | 110 mm dia |
| 78 | Vent cowel 75 mm Dia |
| 79 | Pipe clip 75mm dia |
| 80 | 110 mm dia |
| 81 | Plan floor trap 110 mm dia |
| 82 | Construction of manhole in all type of soil inner size 90 X 60 Cm. 450 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5 10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead.Depth up to 0.5 M |
| 83 | Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m 10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complet Inside size 300 X 300 mm depth upto 0.5 MCement cover with frame. |
| 84 | -do- size 450 x 450mm depth upto0.5 M Cement cover with frame |
| 85 | Construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in CM 1:6, 80mm thick stone slab, jointing of slab in CM 1 : 3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C flooring , earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr.:Size 300Cm. dia outside & 300 Cm. depth. |
| 86 | Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M-15 grade C.C flooring & over stone slab covering ,80 mm thick slab ,jointing of slab in CM 1:3. Ralthal, Kharanja,50 mm thick stone partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos C.I foot rests of approved design ,two No. 450 mm dia each Ferro cementcover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:- Size 200x210x130 cm.(for 10 users) |
| 87 | Construction of open Drain with 112mm thick brick masonry in CM 1:4 Semi circular S.W. glazed channel (confirming to IS Standards) fixed with cement mortar 1:1 over a bed of 100mm thick C.C. 1:5:10, filling of edged with M-15 grade C.C. flooring, 12mm cement plaster 1:4, over all exposed faces, excavation & disposal of earth with in a lead of 50 mtr complete as per approved drawings :250 mm drain,225mm Av. depth width 25 Cm S.W. glazed channel. |
| 88 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make 110 mm dia |
| 89 | 75mm dia |
| 90 | Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make Nahni Trap without Jali 4”110mm dia |
| 91 | Bend 87.5 75mm dia |
| 92 | 110 mm dia |
