Providing Electro Mechanical Accessories And Others At Pump House I Tw Ii For Dadpur Ws Scheme At Murarai I Block Under Bolpur Mechanical Division Phe Dte, Birbhum-West Bengal

Providing Electro Mechanical Accessories And Others At Pump House I Tw Ii For Dadpur Ws Scheme At Murarai I Block Under Bolpur Mechanical Division Phe Dte- 1 Supply and delivery at site of the following submersible pumping machinery and electrical accessories as per approved vendor list of PHED 2 Submersible pumping machinery directly coupled with water proof suitable size motor having following specification :- Pump:Duty condition -17.67 m3/hr, Head- 60 Mtr, Shaft-stainless steel, Impeller- S.S / GM, Outlet Size: 65mm / 80mm., Motor:Submersible type 3 Ph , 50Hz, 415 Volt ± 10% 2900 RPM Motor must be suitable for operation with DOL starter.(Test certificate along with characteristic curve should be submitted at the time of delivery). 3 1.1KV grade 10 sq.mm 3 core XLPE insulated Aluminium armoured cable conforming to IS 7098 (Part-I) 1988, with upto date amendments. 4 1.1KV grade 25 sq.mm 3.5 core XPLE Aluminium armoured Cable. 5 100 Amps re-wireable porcelain fuse unit type TPN Main Switch with steel sheet enclosure(Conforms:IS/IEC600947-1&3) 6 Re-wireable type TPN Changeover switch 100 Amps 415V, 50Hz, 4p offload with steel sheet enclosure (Conforms: IS/IEC60947-1&3) 7 Supply and delivery of the following valves, pipes and gauges etc at site 8 3mtr long 80mm dia UPVC standard type column pipe [cream color] with both side threaded and one end side socketed with registered KPMG 9 1.5 mtr long 80mm dia UPVC standard type column pipe [cream color] with both side threaded and one end side socketed with registered KPMG. 10 80mm dia. CI Top & Bottom adopter. 11 Heavy type suitable dia. MS suspension clamp along with nuts bolts and washers. 12 80mm dia. CIDF Non-Raising Sluice Valves, PN 1.0 rating (Conforming to IS:14846) for delivery pipe line and wash out line.(MOC & TC needed for valve). 13 80mm dia. CIDF single door swing Non Return Valve, PN 1.0 rating (Conforming to IS:5312).(MOC & TC needed for valve). 14 CIDF 90°bend- 1no., CI flanged tee- 1no., blank flange-1no., CI/ MS flanged short piece 0.50 mtr.-1no, CI/ MS flanged pipe 1mtr.- 1 no. etc (as per IS specification and certification registered) for construction of delivery pipe line and wash out line 15 Heavy type 250mm dia./suitable Split type tube well cover with clamping arrangement including supply of nuts, bolts and washer as per departmental design. 16 Anti snapping safety device for pump set by supplying suitable size of MS angle busket and nylon rope of required length includingsupplying of nuts, bolts and all other materials 17 150mm dial Pressure gauge [Range 0-7kg/cm²] with glycerine filling inside the dial including brass cock and fitting complete [This cost includes 15mm. dia G.I. pipes and specials]. 18 Supply and delivery of 100 Amps Kit Kat rewireable procelian fusers carrier & base( Specification -IS 2086) 19 Making brick pillar 0.25 x 0.25 x 0.75 Mtr/Suitable hight for supporting of valves and pipes with 12mm thick plaster and net cement finish complete. 20 Supply & Making necessary GI Medium pipe (dia of pipe not less than 32mm) protection for submersible cable from kiox box to submersible pump-motor set including supply of all specials and complete the job. 21 Laying of one No. cable 16sqmm 3 core ( Departmental supply) in underground trench 460 mm wide x 760 mmaverage depth, with brick protection onthe top of thecable with 8 (eight) Nos. bricks per metre, includingfilling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed. 22 Supply and delivery of ML 1.5 FASDhaving relay range 9- 14 Amp, Three Phase Submersible Pump Controllers. 23 Installation ofstarter,main switch, changeover, cut out etc. all electrical equipment within the pumphouse, drawing of cable properly on suitable size GI cable tray on wall / as per direction of EIC as per layout & IE rules and all connection with supply necessary materials, cable etc to complete the work, making arrangement with supply & fixing of materials for taking power within the pump house from WBSEDCL end as per direction of EIC. 24 Installation of Submersible pumping machinery to newly sunk tubewell along with column pipes (as required), top cover, valves, and specials of above with protection pipe and supply of MS clamp, nut bolt, cable gland socket etc. making inerconnection of the pump delivery line to pump collecting main line near tubewell with supply of all necceasary pipe, reducer/enlarger, GI/MS specials etc. including brick, sand, cement, rod etc and laying & drawing of all actuator cable & cable protection pipe as required and all to complete the job including all connection & testing commissioning as per direction of EIC. 25 Add GST @ 18% 26 Add Cess @ 1%

Refer document

INR 6500.0 /-

Refer document