|
| 1 | M&L for 75 mm thick 1:3:6 PCC type C1 finished even and smooth laid to slope of 1 in 20, laid in alternate bays, each bay not exceeding 2.5 m length withh joint to be 10 mm groove at junction of wall and plinth protection filled withfilled with bituminous sealing compound of grade A/ Bituminous Mastic filler/sealant including demolition of existing PCC in ground floors complete all as specified and as directed. |
| 2 | Demolition of existingWall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets and supply & fixing for 4mm Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Alumi nium framework with screws Note:- Making good of alingments and grid of existing ceiling deemed to be included in quoted rates contractor shall not claim for this. |
| 3 | Taking down existing cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and M&L Rendering 5 mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling finishing as per matching surface including preparation of newly plastered surfaces of ceiling and applying three coat of white wash complete all as specified and directed by Engineer-In-Charge. |
| 4 | Taking down existing cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and M&L Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM (1:4) finished even & smooth (without using extra lime or cement) includingpreparation of newly plastered surface of walls & applying two coats of cement base paint of approved shade / tint over a coat of alkali resistent primerall as specified and directed by Engr-in-charge. |
| 5 | Taking down existing cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and M&L Rendering 10 mm thick on concete surfaces or surface other than onfair face of brickwork in CM (1:6) finishing as per matchingpreparation of newly plastered surface of walls & applying two coats of distemper oil emulsion of approved shade / tint over a coat of alkali resistent primer over and including a layer of 3mm thick wall care putty of approved make complete all as specified and directed by Engineer-In-Charge. |
| 6 | Taking down existing cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and M&L for rough cast finish plaster with a mixture consisting of curshed stone or fine gravel aggregate mixed with coarse sand and cement in the ration of 1:1:1 over and including 12mm thick rendering in cement mortar 1:3 on fair faces of brick masonry or concrete surfaces of wallsincludingpreparation of newly plastered surface of walls & applying two coats of cement base paint of approved shade / tint over a coat of alkali resistent primerall as specified and directed by Engr-in-charge. |
| 7 | Material and labour preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer completeall as specified and directed by Engr-in-charge. |
| 8 | Taking down existing chowkhats or frames with shutters (without taking off shutters from the frames) area exc. 1.5 sq. m but n exc 4 Sqm each and S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 125 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge),minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid forseparately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 9 | Taking down existing chowkhats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each and S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 100 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge),minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid forseparately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 10 | S&F framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled forfixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooksand hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conformed to Fe 410-W (Gde E- 250) quality Acomplete all as specified and as directed . |
| 11 | Taking down existing chowkhats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each and S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge),minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid forseparately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 12 | Taking down existing Shutters of any description area exc 1 sq. m but n exc 2 Sqm each and S&F factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face including 150mm extruded aluminium tower bolt ( 2 for each door) & 125mm extruded aluminium handle ( 2 No each door) complete all as specified and directed.Note : Rate for all above work is included in this item, Nothing extra shall be paid on this account. |
| 13 | Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face including 150mm extruded aluminium tower bolt ( 2 for each door) & 125mm extruded aluminium handle ( 2 No each door) complete all as specified and directed.Note : Rate for all above work is included in this item, Nothing extra shall be paid on this account. |
| 14 | Taking down existing Shutters of any description area exc 1 sq. m but n exc 2 Sqm each & S&F new 35mm thick factory made glazed and skeleton shutters made of second class hard wood (Bonsum/Hollock), open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Part I Section 8 Clause 8.24 (a) kiln seasoned and chemically pressure treated fixed to chowkat including 200 mm long mild steel barrel tower bolt stove enamelled black with bright bolt (ISI marked) (02 Nos in each shutter), 250mm long aluminium alloy anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy (ISI marked) (01 No in each shutter), 100mm size butt hinges of extruded aluminium alloy with galvanized mild steel hinge pin, anodized type B-21 (ISI marked) (02 Nos in each shutter), 125mm long extruded aluminium handles, anodised, fabricated type (ISI marked) (02 Nos in each shutter), Mild Steel 300mm, ordinary rat tail rod patttern springs including roller & roller plate fixed to wooden frame or welded to steel frame making suitable cut out in wall and making good in CM 1:4 (01 No in each shutter), Galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple ( for 01 Nos shutter), applying two coats of synthetic enamel paint over a coat of pink primercomplete all as specified and directed by Engineer-in-charge.Note : Rate for all above work is included in this item, Nothing extra shall be paid on this account. |
| 15 | S&F new 35mm thick factory made glazed and skeleton shutters made of second class hard wood (Bonsum/Hollock), open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Part I Section 8 Clause 8.24 (a) kiln seasoned and chemically pressure treated fixed to chowkat including 200 mm long mild steel barrel tower bolt stove enamelled black with bright bolt (ISI marked) (02 Nos in each shutter), 250mm long aluminium alloy anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy (ISI marked) (01 No in each shutter), 100mm size butt hinges of extruded aluminium alloy with galvanized mild steel hinge pin, anodized type B-21 (ISI marked) (02 Nos in each shutter), 125mm long extruded aluminium handles, anodised, fabricated type (ISI marked) (02 Nos in each shutter), Mild Steel 300mm, ordinary rat tail rod patttern springs including roller & roller plate fixed to wooden frame or welded to steel frame making suitable cut out in wall and making good in CM 1:4 (01 No in each shutter), Galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple ( for 01 Nos shutter), applying two coats of synthetic enamel paint over a coat of pink primercomplete all as specified and directed by Engineer-in-charge.Note : Rate for all above work is included in this item, Nothing extra shall be paid on this account. |
| 16 | Taking down existing Shutters of any description area exc 1 sq. m but n exc 2 Sqm each and S&F new 35 mm thick factory made flush shutters, solid core construction, withblock board core and plywood face panels, commercial type on both side including 200 mm long mild steel barrel tower bolt stove enamelled black with bright bolt (ISI marked) (02 Nos in each shutter), 250mm long aluminium alloy anodised sliding door bolts with hasp (1 Nos for each shutter), staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy (ISI marked) (01 No in each shutter), 100mm size butt hinges of extruded aluminium alloy with galvanized mild steel hinge pin, anodized type B-21 (ISI marked) (02 Nos in each shutter), 125mm long extruded aluminium handles, anodised, fabricated type (ISI marked) (02 Nos in each shutter), Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring overall length of cover plate 140mm (ISI marked) (01 No in each shutter), applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-charge.Note : Rate for all above work is included in this item, Nothing extra shall be paid on this account. |
| 17 | S&F new 35 mm thick factory madeflush shutters, solid core construction, withblock board core and plywood face panels, commercial type on both side including 200 mm long mild steel barrel tower bolt stove enamelled black with bright bolt (ISI marked) (02 Nos in each shutter), 250mm long aluminium alloy anodised sliding door bolts with hasp (1 Nos for each shutter), staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy (ISI marked) (01 No in each shutter), 100mm size butt hinges of extruded aluminium alloy with galvanized mild steel hinge pin, anodized type B-21 (ISI marked) (02 Nos in each shutter), 125mm long extruded aluminium handles, anodised, fabricated type (ISI marked) (02 Nos in each shutter), Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring overall length of cover plate 140mm (ISI marked) (01 No in each shutter), applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-charge.Note : Rate for all above work is included in this item, Nothing extra shall be paid on this account. |
| 18 | Dismantling existing floor, hearthincluding cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and S&F Coloured Non Skid ceramic tiles7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:6) set & joined in neat cement slurry and pointed in coloured cement to matchcomplete all as specified and directed. |
| 19 | Dismantling existingwall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises S&F Coloured Glazed ceramic tiles 300x600 X 7-8 mm thick coloured tile, on walls etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match over 10 mm thick plaster in CM(1:4) set & joined in neat cement slurry and pointed in coloured cement to match complete all as specified. |
| 20 | Dismantling existing floor, hearthincluding cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and S&F Vitrified Ceramic tiles 10mmthick (square/rectangular) double charged , area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:4) set & joined in neat cement slurry and pointed in coloured cement to match complete all as specified. |
| 21 | Dismantling existing floor, hearthincluding cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and M&L double charged viritfiedceramic tiles 10 mm thick (square /rectangular) polished ,area of each tiles not exc 0.36 as in vertical surfaces like dado or skirting over 10mm thick in CM 1:4 set & joined in neat cement slurry and pointed in coloured cement to match complete all as specified. |
| 22 | Dismantling existing floor, hearthincluding cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and S&F Vitrified Ceramic tiles 10mmthick (square/rectangular) double charged , area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:4) set & joined in neat cement slurry and pointed in coloured cement to match complete all as specified. |
| 23 | Dismantling existing floor, hearthincluding cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and M&L double charged viritfiedceramic tiles 10 mm thick (square /rectangular) polished ,area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm as in vertical surfaces like dado or skirting over 10mm thick in CM 1:4 set & joined in neat cement slurry and pointed in coloured cement to match complete all as specified. |
| 24 | Demolition of existing stone slabs and tiles of any description or thickness in floors, aprons etc. and M&L Machine cut kota stone slab flooring 18-20 mm thick over 15mm thick screed in CM(1:6) laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishingcomplete all as specified and as directed. |
| 25 | Demolition of existing stone slabs and tiles of any description or thickness in floors, aprons etc. and M&L Kota stone slab 18-20mm thick in riser of steps, skirting, dado & pillar over 15mm thick plaster in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and as directed. |
| 26 | Demolition of existing stone slabs and tiles of any description or thickness in floors, aprons etc. and M&L for 16 to 18mm thick Granite (of any colour) slab of approved shade as in flooring, platform etc, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) over & including 15mm thick screed bed (bedding layer) in CM (1:6) incl demolition of old stone in any position complete all as specified and directed by Engineer-in-charge. |
| 27 | S&F 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square of any size in each pane including hacking out old broken glass (any thicknesss, size,quality or description) from metal frame and rubbish off the premises; and also painting/oiling new putty to match existing painting/oiling. complete all as specified and as directed by Engineer-in-Charge. |
| 28 | S&F in repair Sheet glass 5.5mm thick, ordinary quality & glazing with rubber gasket bidding n exc 0.5 sq.m in each pane including hacking out old broken glass (any thicknesss, size,quality or description) from metal frame inlcuding punching or drilling out old glazing pins/spring clips and rubbish off the premises; and also painting/oiling new putty to match existing painting/oiling. |
| 29 | Taking down existing chowkhats or frames with door/window/ventilator (without taking off doors/window/ventilator from the frames) of any description and S&F Anodised aluminium frame with power coating of any colour (minimum thickness of power coating 50 micron).for doors, windows , ventilator ,partition with one or more rebates incl demolition of old frame necessary joining cleats for fixing etc complete all as specified and as directed. |
| 30 | S&F Anodised aluminium power coating door,window,ventilationshutters, aluminium section weighing 0.55 kg/m incl necessary joining cleats,glazing clips, ruber neoprene packing,handles Nos in each door , hinges,anodised aluminium snap beading screws etc complete all as sepcified and as directed. |
| 31 | Taking up or down 32mm boresteel tubingand connections, including cleaning for re fixing or removal to store and S&F of cPVC pipeSDR 11 grade outer dia 32 mm bore with all necessary cpvc brass fittings and fixed complete to walls and ceiling or laid in floorsas in sunken complete all as specified and directed by eng- in -charge |
| 32 | M & L for 12 mm thick plaster in CM 1:4 in sunken portion andpreparation of new surfaces and mix with cement and water in the ratio 1:1:5 by volume using DR FIXIT PIDICRETE URP chemical on floor and vertical surface of sunken floor as per Manufacturer\"s instructions complete all as specified and as directed by Engineer-in-charge complete all as specified and as directed by Engineer-in-charge.Note :- For Plaster work using water proofing compound as per manufacture instruction incl this rate nothing to extra paid. |
| 33 | M&L for PCC in 1:5:10 type E2 (using 40mm graded agg) as in sunken floor of toilet including demolition of existing PCC insunken portion complete all as specified and as directed by Engineer-in-charge. |
| 34 | M&L for 50 mm thick PCC type C2 (1:3:6) using 40mm graded stone aggregate in sunken floor as sub base of floor finished complete all as specified an directed by engineer -in - charge |
| 35 | Demolition of existing brick work, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles and M&L for brickwork with subclass `B\" bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6)complete all as specified and directed by Engr-in-charge. |
| 36 | Taking up or down 15mm boresteel tubingand connections, including cleaning for re fixing or removal to store and M&L of cPVC pipeSDR 11 gradedia 15 mm bore with all necessary cpvc brass fittings and fixed complete to walls and ceiling or laid in floorscomplete all as specified and as directed. |
| 37 | Taking up or down 20mm boresteel tubingand connections, including cleaning for re fixing or removal to store andM&L of cPVC pipeSDR 11 grade dia 20 mm bore with all necessary cpvc brass fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and as directed. |
| 38 | M&L, 100mm sand cast Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors or walls incl taking down old any type pipe complete all as specified and directed. |
| 39 | M&L, 75 mm sand cast Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors or wallsincl taking down old any type pipe complete all as specified and directed. |
| 40 | M&L for cPVCpipes incl bend/Tee/L-bow insingle socketed, in any length with rubber ring joints, fixed to walls or laid in tranches or in floor of 75 mm bore of pipe incl taking down of old pipe etc complete all as specified and directed. |
| 41 | M&L for PVCpipes incl bend/Tee/L-bow insingle socketed, in any length with rubber ring joints, fixed to walls or laid in tranches or in floor of 110 mm bore of pipe incl taking down of old pipe etc complete all as specified and directed. |
| 42 | M&L, 100mm CI Bends (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed.. |
| 43 | M&L, 75mm CI Bends (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed.. |
| 44 | M&L, 100mm CI Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed. |
| 45 | M&L, 75mm CI Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed. |
| 46 | M&L, CI Nahani trap 75mm bore with grating incl jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as directed lby Engr-in-Charge. |
| 47 | M&L as in repair brass chromium plated bottle trap with 32mm dia discharge pipe having minimum water seal or 25mm for wash basin with inlet and outlet screwed for pipe or connections including necessary packing , union and cap completeall as specified & directed by Engineer-in-charge. |
| 48 | Supply& fixing in repair vitreous china premium / 1st quality wash down water closet wall hung (with dual hung cistern) EWC white/ivory/off white (closedpattern) incl all necessary accessories like rag bolts / gel gasket etc incl flushing cistern , CP jet sprayand also included all the necessary fillting of PVC pipe up to 1st MH of bldg make Parryware verve AM C022N and C0762 |
| 49 | S&F in repairs Vitreous China wash basin, white, flat back, size 550x400mm or size as per manufacturer excluding pillar taps, waste chain & plug & porcelain stopper but including brackets Waste coupling 32mm bore of PTMT (half or full threaded) |
| 50 | M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying one coat of white wash complete all as specified & directed by Engineer-in-Charge. |
| 51 | M&L for preparation of old decorated, plastered or pointed surfaces of ceiling by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying one coat of white wash complete all as specified & directed by Engineer-in-Charge. |
| 52 | M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots, washing, rubbing down and stopping of distempered surface, filling of cracks etc and applying one coat of oil bound distemper complete all as specified & directed by Engineer-in-Charge. |
| 53 | M&L for preparation of old decorated plastered or unplastered surfaces of walls by brooming down or steel wire brushing,scrapping down smoke soot mulds, moss and efflorescent, salts, filling of cracks etc and applying a coat of cement based paint complete all as specified & directed by Engineer-in-Charge. |
| 54 | M&L for preparation of old decorated, plastered or pointed surfaces of wall by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots, washing, rubbing down and stopping of distempered surface, filling of cracks etc and applying one coat of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali &fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm complete all as specified and as directed |
| 55 | M&L for complete removal of existing treatment of old decorated, plastered or pointed surfaces of wall and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali &fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exteriorprimer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed by Engineer-in-Charge |
| 56 | M&L for preparation of old painted wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 57 | M&L for preparation of old painted steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of approved tint complete all as specified and directed by Engineer-in-Charge. |
| 58 | M&L for preparation of old painted steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of approved tint complete all as specified and directed by Engineer-in-Charge. |
