Defence Government Departments Closing in 0 days TDR #46084093

Tender For Repair/Re-Construction Of Perimeter Wall At Ocf Estate.

Issued by Government Departments · avadi, Tamil Nadu
Tender Value
14.99 Lakhs
Estimated cost
Bid Submission
17 Dec 2024
0 days left
EMD
29991
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
avadi → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender For Repair/Re-Construction Of Perimeter Wall At Ocf Estate.; 1 Dismantling of structuralsteel workincluding doors, gates but excluding framed truss etc and surrender to CE stores 2 Dismantling fencing wire mesh, anytype 3 Demolition of brick work laid in cement mortor 4 Demolition of Concrete of any description and in any position not otherwise specifically provided for 5 Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out with hard dense soil 6 M & L for cement concrete in foundation type- D2, with Mix 1:4:8using40mm aggregate. 7 M & L Sand filling under floors or in foundations including watering and consolidation 8 Returning and filling of trenches including spreading, levelling, watering and well ramming in layers not exceeding 25cm in hard dense soil. 9 M&L for providing Reinforced cement concrete Type-B1 1:2:4 (20mm graded aggregate) forfooting,plinth beam,bases of column, tie beam 10 M&L for providing Reinforced cement concrete Type-B1 1:2:4 (20mm graded aggregate) Columns,pillars, 11 Formwork to sides of pillars, posts, struts, piers,columns and stanchions (square or rectangular design)on rough finished surface of concrete- flat 12 Formwork to sides and soffits of floor or roof beams, Tie beams and similar works on rough finished surface of concrete- flat 13 Material & Labour for providing mild steel TMT bars 12mm dia & over for reinforcement cut to length, bent ot shape required including cranking for columns,hookingend & binding with M.S.wire (annealed)not less than 0.9mm dia or securing with clips etc. 14 Material & Labour for providing mild steel TMT bars8mm dia & overcut to length, bent to shaperequired including crankingfor well steiningand well curbs and binding with and including with M.S.wire (annealed) not less than 0.9mm dia or securing withclip etc. 15 M & L for Brick work with cemet mortar 1:4 using B class bricks, built in straight or curved 16 Material & Labour for rendering 15mm thickness onbrick work with using cement mortar 1:4 including elevation works 17 M&L for Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges, all mitres and stopped ends, 18 M & L for preparing of newsurfaces with one coat primer & Two coat synthetic enamel on steel surfaces of any description, over 10cm in width or girth,not otherwise described 19 Fixing of Framed work as in doors or gates of angle or other sectionwith gusset plates, rails, braces, etc., complete, drilled forfixing of steel sheeting or other covering. Doors, etc. to beprepared for hanging or sliding with and including either hooksand hinges or steel hanging door fittings (exclusive of steelsheeting or other covering, running railsand guides) and hanging; also fastening and fixing complete 20 M&L for preparation ofnew surface by applying one coat primer two coat of plastic emulsion plastered surface of any description over 10cm inwidth or girth.

Corrigendum

Sr No Corrigendum Date Corrigendum Type New Submission Date
1 27-Nov-2024 Bid Auto Extn Corrigendum Bid Auto Extn Corrigendum 17-Dec-2024

BOQ

Name of Work : Repair/Re-construction of perimeter wall at OCF Estate
Sl. No. Item Description
1Dismantling of structuralsteel workincluding doors, gates but excluding framed truss etc and surrender to CE stores
2Dismantling fencing wire mesh, anytype
3Demolition of brick work laid in cement mortor
4Demolition of Concrete of any description and in any position not otherwise specifically provided for
5Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out with hard dense soil
6M & L for cement concrete in foundation type- D2, with Mix 1:4:8using40mm aggregate.
7M & L Sand filling under floors or in foundations including watering and consolidation
8Returning and filling of trenches including spreading, levelling, watering and well ramming in layers not exceeding 25cm in hard dense soil.
9M&L for providing Reinforced cement concrete Type-B1 1:2:4 (20mm graded aggregate) forfooting,plinth beam,bases of column, tie beam
10M&L for providing Reinforced cement concrete Type-B1 1:2:4 (20mm graded aggregate) Columns,pillars,
11Formwork to sides of pillars, posts, struts, piers,columns and stanchions (square or rectangular design)on rough finished surface of concrete- flat
12Formwork to sides and soffits of floor or roof beams, Tie beams and similar works on rough finished surface of concrete- flat
13Material & Labour for providing mild steel TMT bars 12mm dia & over for reinforcement cut to length, bent ot shape required including cranking for columns,hookingend & binding with M.S.wire (annealed)not less than 0.9mm dia or securing with clips etc.
14Material & Labour for providing mild steel TMT bars8mm dia & overcut to length, bent to shaperequired including crankingfor well steiningand well curbs and binding with and including with M.S.wire (annealed) not less than 0.9mm dia or securing withclip etc.
15M & L for Brick work with cemet mortar 1:4 using B class bricks, built in straight or curved
16Material & Labour for rendering 15mm thickness onbrick work with using cement mortar 1:4 including elevation works
17M&L for Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges, all mitres and stopped ends,
18M & L for preparing of newsurfaces with one coat primer & Two coat synthetic enamel on steel surfaces of any description, over 10cm in width or girth,not otherwise described
19Fixing of Framed work as in doors or gates of angle or other sectionwith gusset plates, rails, braces, etc., complete, drilled forfixing of steel sheeting or other covering. Doors, etc. to beprepared for hanging or sliding with and including either hooksand hinges or steel hanging door fittings (exclusive of steelsheeting or other covering, running railsand guides) and hanging; also fastening and fixing complete
20M&L for preparation ofnew surface by applying one coat primer two coat of plastic emulsion plastered surface of any description over 10cm inwidth or girth.

AI Tender Summary

OUR REF NO 46084093
AUTHORITY Government Departments
TENDER VALUE 14.99 Lakhs
LAST DATE 17-12-2024
Authority
Authority Name Ordnance Clothing Factory
Work Description Tender For Repair/Re-Construction Of Perimeter Wall At Ocf Estate.; 1 Dismantling of structuralsteel workincluding doors, gates but excluding framed truss etc and surrender to CE stores 2 Dismantling fencing wire mesh, anytype 3 Demolition of brick work laid in cement mortor 4 Demolition of Concrete of any description and in any position not otherwise specifically provided for 5 Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out with hard dense soil 6 M & L for cement concrete in foundation type- D2, with Mix 1:4:8using40mm aggregate. 7 M & L Sand filling under floors or in foundations including watering and consolidation 8 Returning and filling of trenches including spreading, levelling, watering and well ramming in layers not exceeding 25cm in hard dense soil. 9 M&L for providing Reinforced cement concrete Type-B1 1:2:4 (20mm graded aggregate) forfooting,plinth beam,bases of column, tie beam 10 M&L for providing Reinforced cement concrete Type-B1 1:2:4 (20mm graded aggregate) Columns,pillars, 11 Formwork to sides of pillars, posts, struts, piers,columns and stanchions (square or rectangular design)on rough finished surface of concrete- flat 12 Formwork to sides and soffits of floor or roof beams, Tie beams and similar works on rough finished surface of concrete- flat 13 Material & Labour for providing mild steel TMT bars 12mm dia & over for reinforcement cut to length, bent ot shape required including cranking for columns,hookingend & binding with M.S.wire (annealed)not less than 0.9mm dia or securing with clips etc. 14 Material & Labour for providing mild steel TMT bars8mm dia & overcut to length, bent to shaperequired including crankingfor well steiningand well curbs and binding with and including with M.S.wire (annealed) not less than 0.9mm dia or securing withclip etc. 15 M & L for Brick work with cemet mortar 1:4 using B class bricks, built in straight or curved 16 Material & Labour for rendering 15mm thickness onbrick work with using cement mortar 1:4 including elevation works 17 M&L for Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges, all mitres and stopped ends, 18 M & L for preparing of newsurfaces with one coat primer & Two coat synthetic enamel on steel surfaces of any description, over 10cm in width or girth,not otherwise described 19 Fixing of Framed work as in doors or gates of angle or other sectionwith gusset plates, rails, braces, etc., complete, drilled forfixing of steel sheeting or other covering. Doors, etc. to beprepared for hanging or sliding with and including either hooksand hinges or steel hanging door fittings (exclusive of steelsheeting or other covering, running railsand guides) and hanging; also fastening and fixing complete 20 M&L for preparation ofnew surface by applying one coat primer two coat of plastic emulsion plastered surface of any description over 10cm inwidth or girth.
Basic Detail
Tender No 3655/CEO/e-OTE/011/2024-25/CAP
Bidding Type Tender
Location
City avadi
State Tamil Nadu
Key Dates
Publish Date 27 Nov 2024
Submission Date 17 Dec 2024
Open Date 18 Dec 2024
Finance
Tender Value 14.99 Lakhs
Tender Fee Ref. Documents
EMD 29991
Exemption Not Available
Document List
de2d5107-3fb7-4966-86ec-e8ad28eb0e7c.html
BOQ_235411.xls
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 27, 2024
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 17, 2024
18:00 IST

Corrigendum-1 Issued

Clarifications on tender conditions and amendments issued.

Completed
Dec 17, 2024
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Completed
Dec 18, 2024

Bid Opening Date

Technical bids will be opened and evaluated.

Completed

Tender Documents

Download All (ZIP) ↓
html

de2d5107-3fb7-4966-86ec-e8ad28eb0e7c.html

xls

BOQ_235411.xls

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender