Tender For Improvement And Maintenance Of Wash Water Tank Room To New Water Treatment Plant In Komarapalayam Municipality.
Tender Value
15 Lakhs
Estimated cost
Bid Submission
12 Nov 2024
0 days left
EMD
15000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
komarapalayam → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Improvement and Maintenance of Wash water tank room to New water Treatment Plant in Komarapalayam Municipality.
BOQ
| Sl. No. | Item Description |
| 1 | Supplying and Fixing of Chicken Mesh at plastered surface including all labour charges etc completeas per standared specification. |
| 2 | Plastering with cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand))20mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications (S.I.309) |
| 3 | Remove the Loose Materials Charing V Groove all along the structural cracks in plaster and side wall filling with Dr.Fixit Pidiceal 41G Cleaning the surface and Applying two coats Heavy Duty Cemetitious Acrylic water proof Coating with Dr.FIXIT Pidifin2k. |
| 4 | Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification |
| 5 | Supplying and fabrication and fixing in position of anodised natural colour matt finish sliding window in two track in all floors with following sizes. All the three shutters with slinding arrangements, the bottom section should have Gutter arrangements so as to drain the water entering and made with extruded aluminium section for outer frames as shown below with necessary accessories such rubber beading. Aluminium clips, rubber beading,handle and fixing 4mm thick clear sheet glass including all required for fabrication etc., complete.Necessary dismantling making holes in RCC columns, beams, masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by the departmental officers.The Al.Surfaces is to be anodised with matt finish under electrically condition in accordance with ISI 1868/1962 specification for an average anodic film thick of not less than 15 microns. |
| 6 | Supplying, fabricating and fixing in position of Alumi.Anod.natural colour matt finish door half glazed and half PLB board using 12 mm thickPLB board and 5.5 mm thickglazeddoor using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al. Clips, Best double action floor springs, Aluminium Handles on both sides,floor stopper,Tower bolt, Locks and glass including all materials, Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to theextentrequiredand madegood to theoriginalconditionsafterfixingetc.,complete. The Alumi. surface must be anodised with matt finish under electrically controlled condition in accordance with IS specification 1868 / 1962 of Anodic filthickness of not less than 15 Microns (Fifteen) for all sections. |
| 7 | Painting two coats for Interior surface with approved Interior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. |
| 8 | Wiring with 2x1.5(22/0.3) sqmm PVC unsheathed SC Copper conductor of 1100 V gradein suitable PVC rigid pipe on wall and ceiling with PVC accessories and with T.W. switch box with 5amps F.T. switch in flush with wall covered with hylum sheet of 3mm thick with painting of suitable colour with continuous earth wireconnection of 14 SWG wire for cocealed Light point/fan point (5 points per coil) [ SD No. 24 ] |
| 9 | Wiring with 2x1.5(22/0.3) sqmm PVC unsheathed SC Copper conductor of 1100 V gradein suitable PVC rigid pipe on wall and ceiling with PVC accessories and with 150×100×113mmTW switch box for 5A - 3 pin- non inter lockingCS plugIncluding pin top with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for concealed PVC Plug Point [SD NO36 ] |
| 10 | Supply and fixing of 20 W LED tube light fitting with ISI Mark with all accessoreis including cost of an LED light with accessories and fitting charges etc., complete. |
| 11 | Supply and fixing of 1200mm (48\") AC ceiling fan complete with stepped electronic 300w regulator with 11 meterdown rod on the existing clamp. |
| 12 | Supply and fixing of 450mm sweep heavyduty) AC exhaust fan complete with necessary wall opening and making good of the wall. |
| 13 | Supply and fixing of 30 Watts LED Street Light fitting of approved quality including cost of all materials, labour etc., complete. |
| 14 | Supplying and fixing of rolling shutters shall be pull and push type (Gear operated) made of 18G/3\" lathe sections which consist of five main parts such as curtain, lock plate, guide channels rollers and hood cover. These five main parts are made out of special components detailed below: curtain shall be of 18G/3\" lath sections cut to required size and filled with heavy cast iron / MS clips. For 8\"0\"(2.45m) high rolling shutter lath sections provided shall be not less than 37 numbers. Lock plate shall be 10GMS sheet and attached to the side brackets with 20mm square bar.Side brackets shall be of 10G MS plate and cast iron \"U\" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty \"C\" class 40mm steel pipe and high tensile high carbon coil springs. 2 springs shall be supplied. Side brackets shall be of 10G MS plate and cast iron \"U\" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty \"C\" class 40mm steel pipe and high tensile high arbon coil springs - 2 springs shall be supplied. Hood cover shall be of 0.8mm CRCA sheet reinforced with 25mmx25mmx3mm MS angle or gate channel. The rolling shutter in addition to the above should have pulling hook and shall be coated on exposed area with heavy coat of red oxide primer etc., complete. |
| 15 | Supplyingof Following sizes of PVC pipes andspecials, UPVC Pipes and specials & G.I. pipes and specials etc. including cost and conveyance of pipes etc complete complying with standard specification. |
| 16 | Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC M20 concrete using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed. |
| 17 | GST Amount for providing Service to Government Contract Works for the Above construction works. (GST Amount is the Total GST Amount for total overall quoted amount above this row for this work) |
AI Tender Summary
Tender Timeline
Nov 05, 2024
11:30 IST
Tender Published
Tender notice published.
CompletedNov 12, 2024
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedNov 12, 2024
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender