Supply Of Furniture Items To Ace (Comm.), Se (Comm.), Xen (Comm.) Office At Heerapura, Jaipur - 16.23 Supply Of Computer Table Of Modular Nature Having All The Necessary Arrangement For Keyboard, Cpu, Ups, Printer And Wire Manager Table Top: The Table , Jaipur-Rajasthan

Supply Of Furniture Items To Ace (Comm.), Se (Comm.), Xen (Comm.) Office At Heerapura, Jaipur - 16.23 Supply of Computer Table of Modular nature having all the necessary arrangement for keyboard, CPU, UPS, Printer and wire manager Table Top: The table top of size 900 x 600mm(WxD) would be made out of post formed on 25 mm thick particle board with 0.7mm thick Carvica sheet in half round post formed finish on the front and rear side, matching color compensating laminate fixed on the bottom side. Other two sides are edge banded and duly sealed with 1.5 mm thick PVC edge banding of matching color with high pressure through feed machine. Keyboard Below the table top the keyboard pull out tray having sliding arrangement fixed on side supporting legs with 450mm G.I. telescopic channel. Keyboard of size 750 x 450 made out of 18 mm thick Particle board laminate with 0.7mm thick laminate sheet having all four sides Flat edge banded and duly sealed with 1.5 mm thick PVC edge banding of matching color with high pressure through feed machine. Side Support Two supporting side leg of size 600 x 750mm(WxH) made out of post formed on 18 mm thick particle board with 0.7mm thick Carvica sheet in half round post formed finish on two sides and other two sides are edge banded and sealed with 1.5mm thick PVC edge banding of matching color with high pressure through feed machine. Modesty Panel: Made out of 18 mm thick Particle board laminate with 0.7mm thick laminate sheet of size 900 x 750mm(WxH) having all four sides Flat edge banded and duly sealed with 1.5 mm thick PVC edge banding of matching color with high pressure through feed machine. Total A Particular (Item Rate) Supply of visitor Cushioned chair with seat/back made up of dimensions 50.0 cm (W) x 45.0 cm (H) (approx.) and overall height of Chair 80.0 cm (approx.) with a seat height of 45.0 cm (approx.); Overall width and depth of chair from pedestal 55.0 cm (W) x61.0 cm(D)(approx) upsholstered with fabric high resilende polystyrene from armrestes and tubular frame. Supply of Executive Table size 1500 Wx 750 Dx 725 H (Approx); Top: 18mm made of Thick Pre-Laminated board with 2mm thick PVC edge banding on outer edges; Under Structure; (a) Modesty Panel: 18 mm thick pre laminated particle board; (b) MoEpoxy Polyster coating finished recatngular frame fabricated in 1.2 mm thick CRCA; (c) Epoxy Polyster Powder coated Fabricated Legs;38mmx25mm 1.2mm thick MS ERW ATube; (d) Injection moulded Propylene Cable travel cap and nylon 6 leveler glide with MS Bolts (e) Shell storage with drawer tray 0.6 mm thick & front 0.8mm thick CRCA epoxy polyster powder coat with 10 lever lock, handle and leveller; (f) 0.7mm thick horizontal wire carrier & 0.8 mm thick vertical wire carrier system CRCA epoxy polyster finish powder coat of standard Supply of Executive High Back Revolving Chair-The seat and back shall be made up of 1.2 ±0.1cm. thick hot pressed plywood measured as per QA method described in OCP-QLTA- P14-18 and shall be upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foam shall be designed with contoured lumbar support for extra comfort. The dimensions of the back shall be 49.0 cm. (W) x 71.0 cm and of seat shall be 49.0 cm. (W) x 44.0 cm. (D). The HR Polyurethane foam shall be moulded with density 45 ±2 kg/m3 and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The armrest tops shall be injection moulded from black Polypropylene. They shall be fitted to tubular armrest supports made of dia 2.54 ±0.03cm. x 0.16 ±0.0128cm.thk. M.5. E.R.W. tube and black powder coated (DFT 40-60 microns). The tubular armrest supports should hold together the seat and back. The mechanism shall be designed with 360° revolving type, 1r 12 maximum tilt on pivot at center, Upright position locking, Tilt tension adjustment. The pneumatic height adjustment shall have an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and injection moulded in black Polypropylene. The pedestal shall be fabricated from 0.2 ± 0.02 cm thick HRsheet (IS :DD 1079/HR), powder coated (DFT 40-60 microns) and fitted with an injection moulded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal shall be 60.0 20.5cm. pitch-centre dia. (70.0 ±1.0 cm. with castors). The twin wheel castors shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 42.4 to max 53.4cm, Height min102.4 to max 113.4cm, Width & Depth of Chair as measured from pedestal-Width-70.0 cm and Depth-70.0 cm. Supply of Executive medium back chair with seat/back made of dimensions 50.0 cm (W) x 45.0 cm (H) (approx.) and overall height of Chair 90.0 cm (approx.) with a seat height of 55.0 cm (approx.); Overall width & depth of chair from pedestal 70.0 cm (W) x 70.0 cm (D) (approx.); Upholstered with fabric, High resilience polyurethane foam armrests and tubular frame; Center tilt mechanism, 360 degree revolving mechanism, 17+/-2 deg tilt on pivot at center, Upright position locking. Tilt tension adjustment Pneumatic height adjustment, Telescopic bellow assemble, Pedestal assembly with twin wheel castors of standard make.1079/ HR), powder coated (DFT 40-60 microns) and fitted with an Injection moulded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal shall be 60.0 ±0.5cm. pitch-centre dia. (70.0 ±1.0 cm. with castors). The twin wheel castors shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height-min 42.4 to max 53.4cm, Height min102.4 to max 113.4cm, Width & Depth of Chair as measured from pedestal-Width-70.0 cm and Depth-70.0 cm. Supply of 3 seater metro sofa set, it should be made of MIS with powder coated. The total length of the sofa shall be 1765 mm width of the sofa shall bbe 775 mm and the depth of the shall be 710 mm. The sheet should have thickness of 2mm. Providing & fixing ornamental design central table of overall size 900x450x450mm. The frame aand legs are made up of teak wood with approved design & pattern. The top of the table is covered with toughened glass with bevelled edges. Middle shelf is made of teak wood with 100x100 mat pattern. The table is complete with good quality PU Polish. The wood used in the furniture is perfectly seasoned for optimum moisture content to reduce the possibility of seasonal expansion & contraction of the products.work similar design & size approx complete in all respect as per direction of Engineer in charge. Supply of steel almirah with spray paint finish with 2 steel doors, 3 way bolting system having a rigid 7 lever unpickable lock with duplicate CP key doors & shelves made out of 20 gauge sheet & rest body made out of 22 gauge sheet size 50x36x19 (Including 5 bottom support in over all height) with three fix shelves so as to make four compartment. Supply of steel almirah with spray paint finish with 2 steel doors, 3 way bolting system having a rigid 7 lever unpickable lock with duplicate CP key doors & shelves made out of 120 gauge sheet & rest body made out of 22 gauge sheet cie78x36x20 etc.

Refer document

Refer document

INR 2.82 Lakhs /-