Tender For Construction Of Washrooms At Govt. Degree College Bishnah (Under Higher Education)
Tender Value
5.84 Lakhs
Estimated cost
Bid Submission
29 Oct 2024
0 days left
EMD
11680
Bank guarantee accepted
Document Fee
600
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
bishnah → Jammu And Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Washrooms At Govt. Degree College Bishnah (Under Higher Education) Please Refer To Boq
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: in All kinds of soil |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering –All work upto plinth level. 1 : 5 : 10 (1 cement : 5fine sand : 10 graded nallah stone aggregate 40mm nominal size). |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering –All work upto plinth level. 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded crusher stone aggregate 20mm nominal size) |
| 4 | Providing and laying in position specified grade of reinforced cement concrete 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level. |
| 5 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete |
| 6 | Centering and shuttering including strutting propping etc. and removal of form work for:- Foundations |
| 7 | Centering and shuttering including strutting propping etc. and removal of form work for:- Suspended floors, roofs, landings, balconies and access platform. |
| 8 | Centering and shuttering including strutting propping etc. and removal of form work for:- Edges of slabs and breaks in floors and walls. Under 20cm wide |
| 9 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand) |
| 10 | Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level |
| 11 | Finishing with 12mm Cement plaster of mix:1 : 4 ( 1 cement : 4 fine sand) |
| 12 | Finishing with 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand) |
| 13 | Providing and laying matt finished vitrified tile of specified size having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in outdoor floors such as footpath, court yard multi models etc., laid on 20mm thick base of cement mortar 1:4 (1cement: 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as direction of Engineer-in-Charge, size 300x300x9.8 mm |
| 14 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and ointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 15 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately. for fixed portion in Powder coated aluminum (minimum thickness of powder coated 50 microns). |
| 16 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately. For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately in Powder coated aluminum (minimum thickness of powder coated 50 microns) |
| 17 | Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in-charge. (Cost of aluminum snap beading shall be paid in basic item.) 22.3.1 With floating glass panes of 4.0 mm thickness (weight not less than 10.00 kg / sqm) |
| 18 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in charge. Pre-laminated particle board with decorative lamination on both sides. with complete job. |
| 19 | Internal work-exposed on wall, including fixing the pipe with clamps at 1.00 meter spacing, 15mm nominal outer dia pipes. |
| 20 | Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. 15mm nominal outer dia pipes. |
| 21 | Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. 20mm nominal outer dia pipes. |
| 22 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge.Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. 25mm nominal outer dia pipes. |
| 23 | Providing and applying 2 mm thick white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 24 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer |
| 25 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge.Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm) |
| 26 | P/fixing white vitreous china orissa pattern water closet squatting pan (Indian type W.C pan ) of size 580x440 mm with integral type foot rests with with 100 mm sand cast iron P or S trap, 10 litr low level with white P.V.C. flushing cistern ,inclu.flush pipe with manually controlled devicewith all fittings complete, including cutting and making good the walls and floors wherever required. |
| 27 | P/fixing white vitreous china pedestal typewater closet (European type W.C pan ) with seat and lid ,10 litr low level white P.V.C. flushing cistern, inclu. flush pipe with normally control devicewith all fittings complete. W.C pan with ISI marked white solid plastic seat and lid |
| 28 | Providing and fixing P.V.C low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete: 10 liter capacity -White |
| 29 | Providing and fixing uplasticized PVC connection pipe with brass unions (45 cm length,15 mm nominal bore) |
| 30 | Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 |
| 31 | Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931 (short nose) |
| 32 | Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete, semi rigid 32 mm dia |
| 33 | P/fixing white vitreous china flat back front lipped urinal basin of 430 x 260 x 350 mm size. |
| 34 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 35 | Fixing of water storage tank fittings all complete. |
| 36 | Providing and fixing C.P. brass toilet paper holder. |
| 37 | Providing and fixing 8mm dia C.P./S.S.Jet with flexible tube upto 1 mtr long wit S.S. triangular plate to European type W.C. of quality and make as approved by Enginner-in-charge. |
| 38 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms. |
| 39 | Providing and fixing rectangular shape 453x357 mm mirror of superior glass complete with 6mm thick hard board ground fixed to woden cleats with C.P brass screws and washers complete. |
| 40 | Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete,size (150x10 mm) |
| 41 | Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete,size (100x10 mm) |
| 42 | Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 100 mm size |
| 43 | Carriage of material by mechanical transport including loading/unloading and stacking at site for an avg. distance of 20 kms. Stone Agg. Below 20mm size/C. bajri/Sand |
| 44 | Carriage of material by mechanical transport including loading/unloading and stacking at site for an avg. distance of 20 kms. Bricks |
| 45 | Carriage of material by mechanical transport including loading/unloading and stacking at site for an avg. distance of 20 kms. Labour engaged for site clearance and removal of disposal from sites |
AI Tender Summary
Tender Timeline
Oct 21, 2024
11:30 IST
Tender Published
Tender notice published.
CompletedOct 29, 2024
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 30, 2024
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender