|
| 1 | Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Paving, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to Outside MD/AF Land, complete all as specified and directed. |
| 2 | M&L for Cement Concrete 1:4:8 type D2 (40mm Graded Stone Aggregate) 100mm thick in Sub-bases, complete all as specified and directed. |
| 3 | M&L for Cement Concrete 1:3:6 type C2 (40mm Graded Stone Aggregate), 75mm thick in plinth protectionfinishing cement concrete surfaces even and smooth without using extra cement complete all as specified and directed. |
| 4 | M&L for laying pre-polished 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; incl taking out existing old paver blocks and removing from sitecomplete all as specified and directed.(NOTE: Sand cushioning shall be measured and paid separately) |
| 5 | M&L for sand filling under floors or in foundation incl watering and consolidation complete all as specified and directed. |
| 6 | M&L fpr supply and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. |
| 7 | M&L Providing, cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in coping finished even and smooth without using extra cement complete all as specified and as directed. |
| 8 | Dismantling of Asbestos cement(corrugated, semi corrugated, plain, etc.) sheets in roof/wall coverings and removal from sitecomplete all as specified and as directed. |
| 9 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital orsimilarpattern roof/wall coverings and removal from site complete all as specified and directed. |
| 10 | Dismantling of fibreglass/polycarbonate roofing sheet(corrugated, semi corrugated, plain, etc.) sheets in roof/wall claddings etc and removal from sitecomplete all as specified and directed. |
| 11 | S&F 0.50 mm thick TCT (total coated thickness) pre-coloured galvalume sheets with minimum base metal thickness of 0.45 mm, single skin high rib/multi rib profile galvalume sheetinghaving 1000-1020 mm width and 28-30 mm high crest @ maximum 250-255 mm pitch (centre) with sheets manufactured out of 0.50 mm this TCT (total coated thickness) high tensile galvalume sheets having tensile strength 550 MPA with 18-20 micron top coat over 5 micron primer and 8-10 micron alkyld backer zinc aluminium alloy AZ-150, sheets having a dip metallic zinc (43.5%0 aluminium (55%) & silicon (1.5%) with total mass coating of 150 gms/sqm on both sides, having wide pans with minimum 3 smallstiffening ribs for effective water shedding and special male/female ends with full return legs on laps for purlin support and fixed as per existing profile of roof completeall as specified and directed. |
| 12 | All as per Item No. 11 above but 0.50 mm thick colouredplain galvalume sheet as in ridge/valley gutter of roof. |
| 13 | S&F 2mm thick Polycarbonate sheet, drop embossed design,density 1.2 kg/m3, in any colour, as in wall claddings/roofs including necessary side or end laps duly fixed with coach screws and washers complete all as specified and directed. |
| 14 | Dismantling structural steel work of any description in rafters, purlins and wind ties etc and removal from site complete all as specified and directed. |
| 15 | M&L for steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed.(NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete) |
| 16 | M&L for preparing New or previously untreated Steel and Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Red Oxide Zinc Chrome Primer, complete all as specified and directed. |
| 17 | Demolition of Brick work built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc. Incl removal of debris from site complete all as specified and directed. |
| 18 | M&L for Brick Work with Fly-AshBricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and directed. |
| 19 | M&L Brick work using Serviceable Bricks obtained from Item No. 17 here-in-before including removing old Mortar, Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in cement mortar 1:6, complete all as specified and directed. |
| 20 | Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. to Outside MD/AF Land, complete all as specified and directed. |
| 21 | M&L Rendering 15mm thick in Cement Mortar 1:6 on Brick Walls/Concrete Surfaces, plastered surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed. |
| 22 | M&L for Rendering (Ceiling) 5.0mm thick in Cement Mortar 1:3 on Concrete Surfaces as in Ceiling, etc., Plastered Surfaces finished Even and Smooth, without using Extra Cement, complete all as specified and as directed. |
| 23 | M&L for 15 mm thick plastering in two layers, 10 mm + 5 mm in cement mortar 1:4, top layer of 5 mm thickness mixed withwater proofing compound(as per manufacturer\"s instructions) onbrick/stone walls or concrete surfaces finished even and fair (up to any height) for external surfacescomplete all as specified and directed.Note : Water Proofing compound shall be measured and paid separately as \"Supply only\". |
| 24 | Supply only Liquid Water Proofing Compound, conforming to IS and/or as approved, complete all as specified. |
| 25 | M&L for Rough Cast Plaster on Brick Walls consisting Under Coat of Cement and Sand Mortar 1:3 not less than 10mm thick and while it is still in Plastic state the Rough Cast Mixture consisting of Crushed Stone or Fine Gravel mixed with Coarse Sand and Cement in the ratio 1:1:1 shall be applied and finish Even, complete all as specified and directed. |
| 26 | M&L for preparing New Plastered Surfaces of Walls, applying a coat of appropriate cement primer followed by a Coat of 2 mm thick Wall Putty (in two layers of 1mm thick) including rubbing down with Sand Paper to obtain a smooth finish surface and finishing with Two Coats of Acrylic Distemper (as approved) complete all as specified and as directed. |
| 27 | M&L for Preparing Newly Plastered Surfaces of Ceiling and applying Three Coats of White Wash, complete all as specified and directed. |
| 28 | M&L for preparation of newly plastered surfaces andfinished with two coats ofexterior acrylicemulsion paint (having anti-dust & anti-algae properties) duly mixed with stainer to achieve approved Tint/shade (in camouflage pattern) over a coat of suitable exterior primer, applied with rollers to new wall surfaces of any description, over 10cm width or girth not otherwise described, as per manufacturer\"s instructions, up to 4 storey height complete all as specified and directed. |
| 29 | M&L preparing newly Rough Cast plastered surfaces of Walls and applying two Coats of Exterior Emulsion Paint (having anti-dust & anti-algae properties) duly mixed with stainer to achieve approved Tint/shade(in camouflage pattern) over a coat of suitable exterior Primer (as per Manufacturer\"s instructions), complete all as specified and directed. |
| 30 | Dismantling of ceiling grid frame, any type along with ceiling board of any thickness including cover fillets complete all as specified and directed. |
| 31 | Dismantling ofWallandceilingboards or panels(PVC, fibre, pulp, insulation, etc.) or insulationboards / slabs / blankets, any thickness, including cover fillets, complete all as specified and directed. |
| 32 | S&F false ceiling with powder coated exposed G.I. grid suspension system consisting of Main Runner 3600 mm long, Cross Tee 1200mm/600mm long and Wall Angle, wall angle fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300 mm c/c, Main Runners placed @ 1200mm, Cross Tee 1200mm inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of 1200mm x 600mm and additional cross tees of 600 mm placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600mm x 600mm, grid of module size 600mm x 600mm shall be supported by 6 mm dia G.I. wire from purlins/soffit complete all as specified and directed. Note: Ceiling board will measured and paid separately under appropriate item. |
| 33 | All as per item No. 32 above, but except material (Serviceable GI snap grid obtained from item No. 30 here in before) complete all as secured and as directed. Note: Ceiling board shall be measured separately under appropriate item. |
| 34 | S&F 12mm thick mineral fibre core ceiling board/tiles for insulation and acoustic purposes, 60x60 cm in size, fixed with GI Snap Grid Frame Work with Steel Screws complete all as specified and directed.Note: Snap grid ceiling frame shall be measured separately under appropriate item. |
| 35 | All as per item No. 35 above, but except material (Serviceable boards obtained from item No. 30 or 31 here in before) complete all as specified and as directed.Note: Snap grid ceiling frame shall be measured separately under appropriate item. |
| 36 | S&F 6mm thick HPSC cement fibre plain building boards, fixed to wall, including finishing with 2 mm thick wall puttyin two coats complete all as specified and directed. |
| 37 | M&L for Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame, including various PVC angle/section all as per manufacture instruction and specifications including taking down carefully the existing electric point wiring and making it concealed by cutting grooves on brick walls as required at site for wall panelling complete all as specified and as directed. |
| 38 | M&L for 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. |
| 39 | Dismantling Floor, Paver Tiles, Hearth or Wall Tiling,etc. including Cement Mortar Bedding (but not backing) and removing debris, etc. to Outside MD/AF Land, complete all as specified and directed. |
| 40 | M&L for Non-skid Glazed Ceramic Coloured/Printed floor Tiles 400mm x 400mmx 7-8 mm thick in Flooring, set and jointed in Neat Cement Slurry and pointed in White/Coloured Cement, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and directed.NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate. |
| 41 | M&L for Coloured Glazed Ceramic Tiles in vertical surface 450mm X 350mm X 6-7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the Tiles, laid over and including 10mm thick rendering as Screed or backing coat of wall tilein Cement Mortar 1:4, complete all as specified and directed.NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate. |
| 42 | M&L Vitrified Coloured Tiles 9-10mm thick (Square/ Rectangular), Double Charge, Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Floors, etc. Set and Jointed in Neat Cement Slurry, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, including grouting of joints complete all as specified and directed.NOTE : Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate. Grouting shall be measured and paid separately. |
| 43 | M&L for grouting joints of ceramic floor tiles, area of each Tile not exc. 0.36 Square Metre in Floors, having 3mm joint width using epoxy grout mix of 0.70 Kg of organic coated filler of desired shade (0.10 Kg of hardener and 0.20 Kg of resin per Kg) including filling/grouting and finishing complete all as specified and directed.(NOTE: This item shall be executed only for Item No 44 here-in-before) |
| 44 | M&L Vitrified Coloured Tiles 9 to 10mm thick (Square/ Rectangular) Double Charge, Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Vertical Surface i.e. Dado, Skirting, etc., set and jointed in Neat Cement Slurry and pointed in White or Colour Cement to match the Tiles, laid over and including 10mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and directed.NOTE : Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate. |
| 45 | M&L for providing outdoor ceramic Floor (Paver) Tiles, 400 x 400 x 9-10mm thick, highly abrasive, Anti-skid, Impact Resistant, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete including providing 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.(NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate. |
| 46 | M&L Dismantling Stone Slabs and/or Tiles of any description or thickness in Floors, Aprons, etc. laid, bedded and pointed in Cement Mortar, removal of debris outside AF land, cleaning of area to remove dust, loose particles, washing with water and providingMachine cut Kota Stone Slab 20-25mm thick in Flooring, laid over 20mm thick Screed base in Cement Mortar 1:4 laid and joined with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.NOTE : Cost of Cement Screed Bed shall be deemed to be included in the Quoted Unit Rate. |
| 47 | M&L Dismantling Stone Slabs and/or Tiles of any description or thickness in Floors, Aprons, etc. laid, bedded and pointed in Cement Mortar, removal of debris outside AF land, cleaning of area to remove dust, loose particles, washing with water and providing18-20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cill, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to matchwith shade of granite including grinding and polishing, laid over and including 20mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and directed.NOTE : Cost of Cement Screed Bed shall be deemed to be included in the Quoted Unit Rate. |
| 48 | Demolition Cement Concrete (Reinforced) of slab, facia, Chajja, sunshade, chullah hoods and similar work (reinforcement cut as required to facilitate demolition) and removing debris, etc. to Outside MOD Land, complete all as specified and directed. |
| 49 | M&L for RCC 1:2:4 (type B1) using 20mm graded aggregate as counter/platform supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.NOTE : MS reinforcement shall be measured and paid separately. |
| 50 | M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizontal or sloping) for rough finished surfaces complete all as specified and directed. |
| 51 | M&L for Mild steel bars 10mm Dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm Dia complete all as specified and directed. |
| 52 | S&F in repair Rotational Moulded Polyethene Water Storage Tank, 500 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS, hoisted and fixed in Position complete all as specified and directed. |
| 53 | S&F in repairs Ball Valve 20mm Dia (minimum Weight 210 Gram), high pressure of PTMT with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe, complete all as specified and directed. |
| 54 | S&F in repair Looking Mirror 5.0mm thick of size 600x600mm, fixed with Chromium Plated Brass Spacers 25mm to 30mm in size (One Each Corner) including rounding the edges of the Mirror complete all as specified and directed. |
| 55 | S&F in repair Brass Chromium Plated Tubular Towel Rail 20mm Dia, 60 Cm long with Brackets complete all as specified and directed. |
| 56 | S&F in repair stainless steel Grating Round 100mm Dia with waste hole jointing with Solvent Cement complete all as specified and directed. |
| 57 | S&F in repair Chromium Plated health faucet with 01 mtr long stainless steel tube including necessary fitting and fixtures complete all as specified and directed. |
| 58 | S&F in repair Jet Spray with Connection Pipe 15mm bore (Dia), Brass Chromium Plated and suitable for Wash Down Water Closet Pan (Pedestal Pattern) , complete all as specified and directed. |
| 59 | S&F in repair Vitreous China, white, half stall urinal flat back with grating and union for discharge pipe (excluding flush pipe and flushing cistern and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and Union for discharge pipe complete all as specified and directed.(NOTE: Quoted rate shall be deemed to include for the cost of waste coupling and waste pipe) |
| 60 | S&F in repair brass chromium plated Urinal spreader for fixing with 15 mm dia pipe complete all as specified and directed. |
| 61 | S&F in repair vitreous China floor mounted one piece closet (Pedestal pattern), white including vitreous China valveless syphonic action type flushing cistern with inlet ball valve float,push button, flush pipe incl bracket, P/S trap, PVC soft close seat cover and connecting fittings complete all as specified and directed.(Make : CERA, Model: CHAMP / PARRYWARE, Model: Entice / HINDWARE, Model: FLORA / ASIAN PAINTS, Model: IMMERSE / ESSCO, Cat No: AIS-WHT-101851S220SPPSM ) |
| 62 | S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, with \"P\" or \"S\" trap front or back inlet, fixing bolts (except flushing cistern and flush pipe) incl plastic water closet seat cover (white) and mild steel chromium plated or aluminium hinging device complete all as specified and directed. |
| 63 | S&F in repair PVC Flushing Cistern 10 Litre capacity White, Low Level, Valve less, Syphonic action type with Inlet, Ball Valve, Float and Handle, PVC Waste Pipe 32mm bore (dia) of suitable Length, a pair of Cast Iron Bracket/ Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 complete all as specified and directed. |
| 64 | S&F in repair rectangular shape wash basin, white, counter top type, size 480mmX370mmX130mm provided with 32mm dia Brass Chromium Plated Waste Fitting, PVC waste pipe etc incl making good disturbed Surfaces in Cement Mortar 1:3 and filling joints with whte cement complete all as specified and directed.(NOTE: Cost of CP waste coupling and PVC waste pipe is deemed to be included in the quoted rates.) |
| 65 | S&F in repair Vitreous China wash basin, white, flat back, size 550x400mmprovided with 32mm dia Brass Chromium Plated Waste Fitting, PVC waste pipe, brackets incl making good disturbed Surfaces in Cement Mortar 1:3 and filling joints with whte cement complete all as specified and directed.(NOTE: Cost of CP waste coupling and PVC waste pipe is deemed to be included in the quoted rates) |
| 66 | S&F in repair PVC Connection Pipe 15mm size and 60 Cm in length with Adapter Nuts of PVC, complete all as specified and directed. |
| 67 | S&F in repair PVC (SWR) 75 mmfloor trap plain with grating including jointing with solvent cement complete all as specified and directed. |
| 68 | S&F in repair PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any length with Rubber Ring Joints, laid onfloor, complete all as specified anddirected. |
| 69 | S&F in repairs PVC (SWR) 110mm bore (dia) Soil, Waste and Ventilating Pipe, single socketed, in any length with PVC Joints, with or without Ears, laid on floors, complete all as specified and directed. |
| 70 | S&F in repairs PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, single socketed, in any length with PVC Joints, with or without Ears, fixed to Walls with PVC clips, complete all as specified and directed. |
| 71 | S&F in repair PVC (SWR) 110mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any length with Rubber Ring Joints, fixed to Walls with PVC Clips, complete all as specified and directed. |
| 72 | S&F in repair PVC (SWR) 75mm bore (dia), Bend any type, provided with Access Door, etc. and jointing with Solvent Cement , complete all as specified and directed. |
| 73 | S&F in repair PVC (SWR) 110mm bore (dia), Bend any type, provided with Access Door, etc. and jointing with Solvent Cement , complete all as specified and directed. |
| 74 | S&F in repair 75 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal, with access door complete all as specified and directed. |
| 75 | S&F in repair 110 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal, with access door complete all as specified and directed. |
| 76 | S&F in repair 75 mm bore PVC (SWR) junction single (single T) equal or unequal, with access door complete all as specified and directed. |
| 77 | S&F in repairs 110 mm bore PVC (SWR) junction single (single T) equal or unequal, with access door complete all as specified and directed. |
| 78 | S&F in repair PVC (SWR) vent cowl, 75 mm bore complete all as specified and directed. |
| 79 | Taking up or down Steel Tubing 15mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and directed. |
| 80 | Taking up or down Steel Tubing 20mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and directed. |
| 81 | Supply & laying Steel Water Tubing 15mm bore (dia), Galvanised, ‘medium grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other situation, complete as all specified and directed. |
| 82 | Supply & laying Steel Water Tubing 20mm bore (dia), Galvanised, ‘medium grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other situation, complete as all specified and directed. |
| 83 | S&F in repair Bib Tap 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, LongBody with Capstan Head, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and directed. |
| 84 | S&F in repair Chromium plated brass Pillar tap, with aerator, fixed to wash hand basin, complete all as specified and directed. |
| 85 | S&F in repair angle valve, 15 mm bore, cast copper alloy, chromium plated fancy type, concealed type with wall flange fixed to iron pipe complete all as specified and directed. |
| 86 | S&F in repair Chromium plated brasstwo way Angle valve, fancy type,concealed type with wall flange fixed to 15 mm bore of Iron pipe, complete all as specified and directed. |
| 87 | S&F inrepairs for waste coupling chromium plated for sink /wash basin, suitable for 32mmdia waste pipe complete all as specified and directed.(NOTE: This item shall only be measured for replacement in existing sinks, basins etc) |
| 88 | S&F in repair PVC Waste Pipe 32mm bore (dia), 60-75 cm length (as required at Site), complete all as specified and directed.(NOTE: This item shall only be measured for replacement in existing sinks, basins etc) |
| 89 | Taking down Wooden Chowkhat or Frame with Shutter (without taking off Shutter from the Frame), exc. 1.5 Square Metre but not exc. 4.0 Square Metre Each, complete all as specified and directed. |
| 90 | Taking down Chowkhat or Frame (any type) with Shutter (without taking off Shutter from the Frame), n.exc. 1.5 Square Metre Each, complete all as specified and directed. |
| 91 | Taking down and refixing of Shutters of any descriptionin same opening n exc 1sq. m each complete all as specified and directed. |
| 92 | S&FPressed Steel Frame of size 105x60mm using 1.25mm thick Mild Steel Sheets for Doors with One or More Rebates incl necessary Fixing Lugs, Hinges, Lock Strike Plate, etc., complete all as specified and directed. |
| 93 | S&F Pressed Steel Frame of size 125x60mm using 1.25mm thick Mild Steel Sheets for Doors with One or More Rebates incl necessary Fixing Lugs, Hinges, Lock Strike Plate, etc., complete all as specified and directed. |
| 94 | M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) as in Filling Back side of Pressed Steel Frame, complete all as specified and as directed. |
| 95 | M&L for Flush Shutters of 35mm thick, ISI marked, solid core construction with block board core and plywood face panels, commercial type on both sides and fitted to Steel Frame, complete all as specified and directed. |
| 96 | M&L Panelled Shutter 35mm thick ofSecond Class Hardwoodwith Panels of 12mm thick Veneered Particle Board medium density wood with commercial face veneered both side and fitted to Chowkhat, having size of Rail and Stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed. |
| 97 | M&L Glazed and Skeleton Shutter 35mm thick of Second Class Hardwoodprepared to receive Gauge/Glass (without Sash Bars) fixed with mitred beads supplied and fitted to Chowkhat and securing Glass, Gauge, etc. sizes of Members of Shutter as specified in SSR Part-I, Section-8, Clause 8.24(a), complete all as specified and directed.(NOTE: Mosquto proof netting shall be measured and paid seperately) |
| 98 | M&L preparing new or previously untreatedWood and Wood Based Surfaces of any description, not otherwise described, over 10 Cm width or girth and applying two Coat of Synthetic Enamel Paint (First quality), over a coat of wood primer complete, including cleaning the surface,all as specified and directed. |
| 99 | Providing and fixing factory made uPVC white colour Sliding window Three track, area not exceeding 2.00 sqm each, made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories complete all as specified and directed.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) |
| 100 | S&F Steel Window Box type using ERW ‘P’ Section comprising Double Frame for Gauged and Glazed Skeleton Shutters, having Outer Frame of Section 50x25mm and Inner Frame of Section 40x20mm, jointed internally with Mild Steel Flat Iron 40x3mm complete with Stainless Steel Tower Bolts, Hinges, Handles, Stops, Lugs, etc. including Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm, guard bars etc., complete all as specified and directed.NOTE :- (a)For the purpose of Measurement and Payment Double Shutters with Frame shall be considered as ONE UNIT. (b)Unit Rate quoted shall deem to be include all the Stainless Steel Builders & Hardware as required/directed at Site. (c)Quoted Unit Rate shall also deem to be include Mild Steel Guard Bars of 10mm Square Bar, spacing at 10 Cm centre to centre on both Vertical & Horizontal directions.(d)Sheet Glass shall be Measured and Paid for separately under appropriate Item. |
| 101 | S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded for fixing wire mesh including one shop coat of priming, complete all as specified and directed.(NOTE : Sheet glass for glazing shall be measured and paid separately) |
| 102 | S&F Factory made solid PVC door frame (Chowkhat) of size 100 mm x 45mm made out of 5mm thick single side prelam PVC Sheet & edges painted to match with the prelam sheet, frame reinforced with MS square tube of size 40mm x 20mm of 19 gauge throughout the frame, fixed in opening as per specification & drg and as per manufacturer instructions complete all as specified and directed. |
| 103 | M&L for Factory made solid PVC moulded door shutter, 28 to 30 mm thick (stiles) with 2,4 or 6 raised panel design with 2 mm thick 3D wood grain moulded PVC Sheet polyurethane painted on the front face & 2 mm thick prelam PVC sheet on back face with particle board core suppling & fixing in the frame at site with aluminium hinges ss per specification & drawing and fixing in the Frame complete all as specified and directed.NOTE : Aluminium Hinges will be Measured and Paid under appropriate Item. |
| 104 | S&F anodised aluminium frame for door, windows, partitions and ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer-in-Charge. |
| 105 | S&F anodised aluminium doors shutters, aluminium section weighing 0.55 Kg/metre including necessary jointing cleats, glazing clips rubber packing handle 2 Nos in each door, hinges, Mortise lock vertical type size 100 mm 4 levers of brass in each door, anodised aluminium snap beading screws etc as per manufactures instruction complete all as specified and directed.(NOTE:- Quoted rate is deemed to be inclusive of the cost of include for anodised aluminium hard ware as indicated, glazing clips, rubber packing, anodised aluminium snap on beading for fixing glass panes in frames, handle, Mortice Lock etc as described in item. Sheet glass shall be measured separately) |
| 106 | S&F anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium section weighing 0.55 Kg/metre including necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as suitable 150 mm long peg stays (01 No), hinges type B-21 100 mm long (02 Nos), suitable handle - 01No each shutter etc as per manufactures instruction complete all as specified and directed.(NOTE: Quoted rate is deemed to be inclusive of the cost of include for anodised aluminium hard ware as indicated, glazing clips, rubber packing, anodised aluminium snap on beading for fixing glass panes in frames, handle etc as described in item. Sheet glass shall be measured separately) |
| 107 | S&F Butt hinges of size 100mm, cold rolled mild steel, heavy duty complete all as specified and directed. |
| 108 | S&F Butt hinges of size 100mm, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed. |
| 109 | S&F Aluminium Handle 150mm long (weight not less than 120 Gram), Extruded Section, Fabricated type, anodised, complete all as specified and directed. |
| 110 | S&F Aluminium Barrel Tower Bolt 200mm long (weight not less than 210 Gram), Extruded Section, complete all as specified and directed. |
| 111 | S&FAluminium alloy, anodized, Sliding Door Bolt 250mm long with Hasp Staple (Bolt type) and Fixing Clips of Sheet cast or extruded section and fixing Bolts and Sliding Bolts of extruded section and fixing, complete all as specified and directed. |
| 112 | S&Fin repairs Door Spring of Mild Steel 150mm long, Ordinary Rat Tail type, Rod pattern Springs including Roller and Roller Plate welding with frame , etc., complete all as specified and directed. |
| 113 | S&F in repair Door Closer Aluminium (Die cast) body, hydraulically regulated, Designation No. 3, Universal type, suitable for Door Shutters of 851mm to 1000mm in width and of weight between 61.00 to 80.00 Kilogram , complete all as specified and directed. |
| 114 | S&F in repair Double Action Floor Spring Hydraulically Regulated made up of minimum 1.25mm thick Aluminium alloy Sheet Foundation Box, Main Body with Stainless Steel Cover, Governing Pivot made of Brass, Other Parts made of Mild Steel heavy duty, complete all as specified and directed. |
| 115 | S&Fin repair Mild Steel Mortice Lock 100mm in size, 4-Lever, Vertical type, complete all as specified and directed. |
| 116 | S&F Sheet Glass 5.50 mmthick, Tinted (as approved by GE), fixed to Aluminium Windows, doors etc of size exc 0.50 sqm each pane complete all as specified and directed. |
| 117 | S&F Sheet Glass 4.8 mm thick, Ordinary quality and glazing in Square exc 0.50 Sqm in Each Pane of aluminium Windows complete all as specified and directed. |
| 118 | S&F Sheet Glass 4.8 mmthick, Frosted (as approved by GE), fixed to Aluminium Windows of size exc 0.50 sqm each pane complete all as specified and directed. |
| 119 | S&F 12mm thick Prelaminated particle board / Engineered Wood Board, interior grade, prelaminated both side with decorative choice lamination, fixed with screws to aluminium frame work etc complete all as specified and directed. |
| 120 | S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. |
| 121 | Hacking out old broken Glass (any thickness, size, quality or description) from Wooden or Metal Frames, glazed with putty or fixed with beads, complete all as specified and directed. |
| 122 | S&F Sheet Glass 4.0mm thick, Ordinary quality and glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane of Steel Windows, complete all as specified and directed. |
| 123 | S&F Sheet Glass 4.0mmthick, Frosted (as approved by GE), and glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane of Steel Windows, complete all as specified and directed. |
| 124 | Repairing of Aluminium Door, Windows, Ventilators Shutter Fixed/ Side Hung /Sliding Type including replacement of necessary Jointing Cleats, Glazing Clips, Rubber Neoprene Packing, Aluminium Snap Beading, Screws, etc. and repairing of Locking Arrangement if any, complete all as specified and directed.NOTE : Cost of Materials requiredfor replacement of unserviceabel parts & smooth functioning of Shutter shall deem to be included in the Quoted Unit Rate. |
| 125 | M&L for Forming Embankment including Raising or Lowering with a Mixture of Saw Dust and coarse Sand (mixed in a ratio of 1:3), Spreading in layers not exc. 30 Cm thick required size, made up to desired shape up to 4.50 Metre high from base on Small Arms Range (Firing Range) of Butt Wall including proper ramming and compaction of each layer before applying subsequent layers complete all as specified and as directed by Engineer-in-Charge.NOTES: 1)Saw dust & coarse sand shall be arranged by contractor from outside AF area under his own arrangement and cost of the same shall be deemed to be included in quoted rate. |
