|
| 1 | EARTH WORK |
| 2 | Surface dressing of the ground, including removing vegetation and inequalities not exceeding 15 cm depth and disposal of rubbish, lead upto 50 m and lift upto 1.50 m. |
| 3 | Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m. |
| 4 | Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete. |
| 5 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m |
| 6 | CONCRETEWORK |
| 7 | Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 8 | RCCWORK |
| 9 | Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in :a) (M20) 1:1.5:3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size) |
| 10 | Reinforcedcementconcreteinwalls(anythickness)includingattachedpillasters, buttresses,plinthandstringcourse, filletsetcfromtop offoundationup to doortwo level includingfinishing and plastering (he exposed surfaces with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding6 mm to give a smooth and even surface excluding cost of centring, shuttering and reinforcement in :a) M20 (1 cement : 1.5 corase sand : 3 stone aggregate 20 mm nominal size) |
| 11 | Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size). |
| 12 | Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1: 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 13 | Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 14 | Centring and shuttering including strutting, propping etc and removal of form work for : |
| 15 | a) Foundation, footings, bases of columns etc. and mass concrete. |
| 16 | b)Walls(any thickness)including attachedpilasters,buhresses,plinthandstring courses etc. |
| 17 | c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).Note: Timber used 8 times |
| 18 | d) Lintels, beams, girders, bressumers and cantilevers etc. Note: Timber used 8 times |
| 19 | e) Column, pillars, posts and struts etc. Note: Timber used 8 times |
| 20 | Reinforcement of RCC work including bending, binding and placing in position complete.b) Tar/TMT steel |
| 21 | BRICKWORK |
| 22 | Brick work with best available local bricks in foundations and plinth in cement mortar 1:6 (1 cement : 6 fine sand). |
| 23 | WOODWORK |
| 24 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). |
| 25 | Providing and fixing iron pressed butt hinges bright finished with necessary screws etc complete.a) 125 x 65 x 2.12 mm |
| 26 | Providing and fixing MS tower bolts (barrel type) with necessary screws etc. completea)250X10 MM |
| 27 | Providing and fixing MS handles with necessary screws etc complete |
| 28 | STEEL WORK |
| 29 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 30 | Providing and fixing in position collapsible steel shutters with vertical channels 20 mm x10 mm x 2 mm and braced with flat iron diagonals 20 mm x 5 mm size with top and bottom rails of T iron 40 mm x 40 mm x 6 mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint. |
| 31 | Supplying and fixing rolling shutters of approved make, made of 80 x 1.25 mm MS laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete but excluding the cost of the top cover and spring. |
| 32 | Providing and fixing 27.5 cm long wire spring grade No.2 for rolling shutters, |
| 33 | Providing and fixing top cover for rolling shutters. |
| 34 | Providing and fixing ball bearing for rolling shutters |
| 35 | Steel work in built Uptubulartrusses inclu¢ling cutting, hoisting,fixing in position andapplying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding la be paid separalely) |
| 36 | welding by electric plant |
| 37 | Steel woil‹ welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of appr0ved steel primer using structuralsteel etc. as required.b) In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 38 | Providingand fixing hand rail of approvedsize by weldingetc. to steel ladder railing, balcony railing,staircaserailingandsimilarworks, includingapplyingprimingcoat of approved steel primer.M.S. tube |
| 39 | FLOORING WORK |
| 40 | Providing and laying ceramic glazed floor tiles of size 300X300 mm (thickness to be specified by manufacture of 1st quality conforming to IS : 15622 of approved make in colours sach as white, ivory, Fume red brown, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand ), jointed with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc. complete. |
| 41 | Kotastone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :a) 25 mm thick |
| 42 | ROOFING WORK |
| 43 | Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately). |
| 44 | FINISHING WORK |
| 45 | 12 mm cement plaster 1 : 6 (1 cement : 6 fine sand). |
| 46 | 15 mm cement plaster 1 : 6 (1 cement : 6 fine sand) on the rough side of single or half brick wall. |
| 47 | 6 mm cement plaster to ceiling 1 : 4 (1 cement : 4 fine sand). |
| 48 | Providing two coats of acrylic water based wall putty/ wall filler of Asian paints/ Berger / Dulux over concrete/ cement plaster / brick wall and ceilling both internal and external after removing all the loosely adhering material from the wall/ ceilling surface with the help of emery stone, putty, blade or wirw brush, moistenning the wall with the help of sufficient quality of clear water as specified and directed by department. |
| 49 | Painting two or more coats (excluding priming coat) with superior ready mixed paint for steelwork of approvedbrandand manufacturein all shades on new work to give an even shade. |
| 50 | ALUMINIUM WORK |
| 51 | Providing and fixing aluminium work for doors, window and ventilator and partitions with extruded built up standard section / approved Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixed with rawl plugs and screws or with fixed clip or with expansion hold fasteners including necessary fillingup of gaps at junction, at top, bottom, and sides with required PVC/ neoprene felt etc. Aluminium section shall be smooth, rust free straight, mitred jointedmechanically wherever required including cleat angle , Aluminum snap beading for glazing panelling C.P brass/ stainless stell srews all complete as per architectural drawings and the directions of Engineer in charge (glazing and panelling to be paid separately )Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) |
| 52 | Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of enginner - in charge ( cost of alumnium snap beading shall be paid in basic itemWith float glass panes of 5.5 mm thikness. |
| 53 | PVC & UPVC WORK |
| 54 | Bed&OtherDoorSh utters:-ProvidingandfixingfactorymadepanelPVCdoor shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mmx 19 mm for stylesand 15x15 mm for top & botiom rails. M.S. frame shall have a coat of steel primersof approvedmakeand manufacture.M.S.frame coveredwith 5 mm lhick heal moulded PVC ’C\" channel ot size 30 mm thickness,70 mm width out of which 50 mm shall be flat and20 mm shall be tapered in 45 egree angle on bolh side forming styles and 5 min thick, 95 mm wide PVC sheet out of which hmm shall be flat and 20 mm shall be tapered in 45 degree on the inneiside lo form top and bottom rail and115mmwidePVCshee\"outofwhich75mmshalldeflatand20 mm shallde tapered on bolh sides to form lock rail. Top, bottom and lock rails shall de provided both side of the panel. 10 mm (5 mm x 2 ) thi¢k, 20 mm wide cross PVC sheef be provided as gap insert for top rail & bottom rail, paneling of 5 mm thiCk doth side PVC sheet to de fitted in the M.S.framewelded/sealed to the styles&railswith 7 mm (5 mm+2mm) thick x 15 mm wide PVC sheet beadingon inner side, and joined togetherwith solvent cement adhesive.An additional 5 mm thick PVC strip of 20 mm width is to be stuck on lhe interiorsideofthe \"C’ Channelusing PVC solventadhesive elc. completeas per direction of Engineer-in-charge, manufacturer\"s specification & drawing.a) 30 mm thick plain PVC door shutters |
| 55 | Sanitary |
| 56 | Providing and fixing white vitreous china type water closet pedestal (European type WC pan)with seat and lid CP brasshingesand rubber buffers, 12.5 Litreshigh level Cl flushingcisternwith fittingsRS or Cl brackets,galvanizedsteel telescopicflush pipe with fittings and clamps, 20 GI overflow pipe with specials and mosquito proof coupling ofapprovedmunicipaldesignandGI chainand pullcompleteincludingpaintingof cistern and fittings, cutting making good the walls and floors where required.a) WC pan with white plastic seat and lid. |
| 57 | Providing and fixing white vitreous china flat back or wall corner/pe dipped front urinal basin of 430x260x350 mm and 340x430x265 mm sizes respectively with CI automatic flushing cistern with fittings, RS or Cl brackets standard size galvanized steel flush pipe and spreaders with brass unions and GI clamps complete including painting of cistern and filings, cutting and making good the walls and floors where required. |
| 58 | a) One urinal basin with 5 Limes Cl automatic flushing cistern |
| 59 | c) Range of three urinals with 12.5 Litre CI automatic flushing cistern |
| 60 | Providingand fixingwhitevitreouschinawash basinwith RS or Cl brackets painted white 15 mm CP brass pillar Gaps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.a) Flat back wash basin size 550x400 mm with a pair of 15 mm CP brass pillar taps of heavy quality |
| 61 | Providing andfixingCPbrasstowelrailcompletewithCPbrassbracketsfixedto wooden cleadt with CP brass screws (heavy quality).a) 750 x 20 mm size |
| 62 | Providing and fixing toilet paper holder.a) CP Brass |
| 63 | Providing and fixing mirror of superior glass {of approved quality) and of required shape and size with plastic moulded frame ol approved make and shade with 6 mm thick hard board backinga) Circular shape 450 mm dia |
| 64 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever requireda) Kitchen sink with drain boardi) 510x1040 mm bowl depth 250 mm |
| 65 | Water Supply |
| 66 | Providing and fixing brass bib cock of approved quality.a)15 mm nominal bore |
| 67 | Providing and fixing brass full way valve with wheel of approved quality.b) 40 mm nominal bore |
| 68 | Providing and fixing non-return valve of approved quality. |
| 69 | a) 25 mv nominal bore |
| 70 | c) 40 mm nominal bore |
| 71 | Providing and fixing CP brass shower rose with 15 mm or 20 mm dia inlet.a) 100 mm dia |
| 72 | Providing and fixing ball valve (brass) of approved quality CompleteA) High pressure with copper floatsa) 15 mm nominal bore |
| 73 | ProvidingandfixingChlorinatedPolyvinylChloride(CPVC)pipes,havingthermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/cfixingthe pipe with clampsat 1.00 m spacing.This includesjointingof pipes& likings with one step CPVC solvent cement and the cost of cutting chases and making goodthe same includingtestingofjointscompleteas perdirectionof Engineerin Charge.a) Concealed work, including cutting chases and making 9oOd the walls etc. |
| 74 | i) 15 mm nominal ou[er dia Pipes |
| 75 | ii) 20 mm nominal outer dia Pipes |
| 76 | iii) 25 mm nominal outer dia Pipes |
| 77 | ProvidingandfixingChlorinatedPolyvinylChloride(CPVC)pipes,havingthermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. Thisincludesjointingofpipes&fittingswithonestepCPVCsolventcement, drenching, refilling & testing of joints complete as per direction of Engineer in Charge.a) External work |
| 78 | i) 15 mm nominal outer dia Pipes |
| 79 | v) 40 mm nominal outer dia Pipes |
| 80 | viii) 75 mm nominal outer dia Pipes |
| 81 | ix) 100 mm nominal outer dia Pipes |
| 82 | Providing and fixing C.P. brass long nose bib Sock of approved quality conforming to IS standards and weighing not less than 810 gms.a) 15 mm nominal bore |
| 83 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.a) 15 mm nominal bore |
| 84 | Providing and fixing C.P.brassstopcock(concealed)ofstandarddesignandof approved make conformingto IS:8931.a) 15 mm nominal bore |
| 85 | Providingand fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conformingto IS:8931a) 15 mm nominal bore |
| 86 | Providingand placingonterrace(at all floor levels) polyethylenewater storagetank, Life IS:12701 marked, with cover and suitable locking arrangement and making necessaryholesfor inlet,outletand overflow pipesbut without fittings and the base support for tank. |
| 87 | Drainage |
| 88 | Providingand Layinglight duty non-pressureNP2 Class RCCpipes with collarsjointed withstiffmixtureofcementmortarintheproportionof1:2(1Cement: 2finesand) includingtesting joints eic complete. |
| 89 | a) 100 mm dia RCC Pipes (NP2) |
| 90 | b) 150 mm dia RCC Pipes (NP2) |
| 91 | Constructingbrickmasonrymanholewith2ndclassbricksincementmortar1:5(1 cement :5 fine sand) RCC top slab with 1:2:4 mix (1cement : 2 coarse sand : 4 stone single 20 mm nominal size),foundation concrete1:4:8 mix (1cement : 4 coarse sand 8stoneaggregate40mmnominalsize)insideplastering12mmthickwithcement mortar 1:3 (1cement : 3 coarse sand) finished with aCoating coat of neat cement and making channels in cement (concrete 1:2:4 mix(1 cement: 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design. |
| 92 | a) Inside size 90 x 80 cm and 45 cm deep includingClcover with frame (light duty) 455 x 610 mm internal dimensionstotal weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg). |
| 93 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
