Tender For Construction Of Community Sanitary Complex At St. George Ground Near Motor Stand.
Tender Value
2.99 Lakhs
Estimated cost
Bid Submission
07 Oct 2024
0 days left
EMD
5980
Bank guarantee accepted
Document Fee
750
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
pedong → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Community Sanitary Complex At St. George Ground Near Motor Stand.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation of foundation trenches or drains in all sorts of soil (including mixed soil but excluding laterite or sand stone) including removing, spreading or stacking the spoils within a lead of 75m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.(a) Depth of excavation not exceeding 1.500 mm. . |
| 2 | Brick soling with picked jhama bricksincluding preparation of bed as necessary, with brick joints properly filled in and packed with powdered earth and including necessary cushion of similer material below the soling (and in between layers when more than one layer is used) complete as per direction. (a) Single brick flat soling (thickness 75 mm.). |
| 3 | (I) Cement concrete with graded stone ballast (40 mm size) excluding shuttering.In ground floor. (B) With N.B variety stone metal. (a) 1:3:6 proportion. |
| 4 | Rubble masonry in cement (1:4) with hard dressed stones from approved quarries and clean, coarse and washed sand including carriage of all materials to site. In Fine dressed work in Building. In Ground Floor |
| 5 | Ordinary cement concrete(mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttring and reinforcement, if any, in ground floor as per relevant IS codes. (b) River bazree. |
| 6 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc.initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at inter-section, complete as per drawing and direction. (a) For works in foundation, basement and up to roof of ground floor/up to 4m. Tor steel/Mild steel. JSWL/JSP/SHYAM/SRMB/BMSAL |
| 7 | Hire and labour charge for shuttering with centreing and necessary staging up to 4 m. using approved stout props and thick hard wood planks of approved thick ness with required bracing for concrete slabs, beams, columns, lintels curved or staight including fitting fixing and striking out after complection of works. (up to roof of ground floor). (a) 25 mm. to 30 mm. thick wooden shuttering as per decision & direction of the Engineer-in-charge. |
| 8 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. |
| 9 | Plaster ( to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (ground floor). [Excluding cost of chipping over concrete surface]. (ii) With 1:4 cement mortar. (a) 20 mm.thick plaster. |
| 10 | Supplying and laying true to line and level Anti-Skid, Full Body,Homogeneous & Granular finish Vitrified Tiles conforming to IS:15622-2006 & IS 4457-2007 and testing shall be made in accordance withIS:13630 [Non- modular sizes for tiles with Skid resistance > 0.5, Mohr\"shardness > 5.0, Staining resistance: Class-1, Water Absorption: E <0.5%], MOR > 35 N/sq.mm in Internal area of building e.g. Toilet Block, Passage, Corridor, Accessible Open Terrace etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg./Sqm or using Polymerised Adhesive (6 mm thicklayer applied directly over finished artificial stone floor/ Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per Sqm below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles/ epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles wi |
| 11 | Supplying,Fitting & fixing 1st quality Ceramic tiles inwalls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20 Kg/Sq.m. (a) Area of each tile up to 0.09 Sq.m. (i) Coloured decorative. |
| 12 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame excluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be corrected up to three decimals). (i) Other Local Wood. |
| 13 | Supplying solid flush type doors of commercial quality, the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan orsimilar wood veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fittings in ground floor. (a) 35 mm thick shutters (single leaf) |
| 14 | Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured fromrolled steel sections conforming to IS 7452-1974 with non-friction projecting (b) Openable steel windows as per IS sizes with side hung shuttersand horizotal glazing bars. [The extra rate admissible for theopenable portion only] type, box type hinges, glazing clips, lugs locking bracket,handle plate etc, including hoisting in position, straightening ifrequired, fixing lugs in cement concrete ( 1:2:4) with stone chips 20mm down cutting holes and mending good damages to match withexisting surface complete in all respect excluding glazing.(Add extra @ 1.2 % for each additional floors upto 4th floor and @1.5% for each addl. Floor above 4th floor.)In Ground floorFlash butt welded windows and ventilators(No shop priming will be allowed to facilitate inspection ofworkmanship)Without integrated grill |
| 15 | Iron butt hinges of approved qualityfitted and fixed with steel screws, with ISI mark. (iii) 75mm x 40 mm x 1.12 mm. |
| 16 | Anodise aluminium barred/tower/socket bolt (full covered) of approved manufactured from extruded section conforming to I.S.204/74 fitted and Fixed with cadmium plated screws: (ii) 75 mm long x 10 mm dia. bolt. |
| 17 | Anodise aluminium Aldrop/Slidingbolts of approvedquality manufactured form extruded section conforming to I.S. specifictation (I.S.2681/66) fitted and fixed complete. (i) 250 mm x 16 mm dia. Bolt. |
| 18 | supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar , end bifurcated with necessary screws etc. by cement concrete (1:2:4) as per direction . ( cost of concrete will be paid separately). (a) 40mm x 6mm, 250mm Length. |
| 19 | (a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 20 | (b) Priming one coat on timber or plasteredsurface with syntheticenamel oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 21 | (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sandparpering etc. in cluding using of approved putty etc. on the surface , if necessary. (a) On timber or plastered surface: (1) With super gloss (hi-gloss). (iv) Two coats (with any shade except white). |
| 22 | (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sandparpering etc. in cluding using of approved putty etc. on the surface , if necessary. (b) On steel or other metal surface: (1) With super gloss (hi-gloss). (ii) Two coats( white in shade ). |
| 23 | Applying interior grade acrylic primer of approved quality and brand on plasteredor concrete surface old or new surface to received distemper /Acrylic emulsion paint including scraping and preparing the surface thoroughly , complete as per manufactured specification and as per directions of the EIC.In ground floor. (a) one coat. (i) water based interior grade Acrylic primer. |
| 24 | Protective and decorative Acrylic exterior emulsionpaint of approved quality , as per manufacturespecification as per direction of EIC to be apply over Acrylic primer as required. the rate included cost of material , labour scaffoldic and all incidential charges but excluding the cost of primer.In ground floor ( two coat). (a) Normal Acrylic emulaion. |
| 25 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992. Single socketed3 meter length. 110 mm. |
| 26 | Supplying, fitting and fixing Shallow water closet Indin pattern (I.P.W.C) of approved make in white vitreous chinawarein position (excluding cost of concrete for fixing). 450 mm long. |
| 27 | Construction of Septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (4:1) including two 560 mm dia. R.C.C. manhloe cover of approved make supplied, fitted and fixied in the top slab with necessary fittings, 19 mm thick cement plaster(4:1) with neat cement finish to the internal surfaces and 12 mm thick plaster(4:1) to outside wall upto 200 mm below G.L. floor finished with 25 mm thick grey artificial stone including supplying, fitting and fixing all necessary specials, fittings, S.W. tees, C.I. foot rest etc. including excavating earth in all sorts of soil, shoring, bailing and pumping out water as necessary, ramming, dressing the bed and refilling the sides of the tank with earth, removing spoils, fliing up the chamber with clear water, removing foreign materialsfrom the chamber and including constructing attached inspection pit as per approved dawing and connecting all necessary pipes, joints etc. with internal plaster workFor 20 users. B) With Bazree (N.B Varity) ( SAIL/TATA/RINL) |
| 28 | Supplying, fitting and fixing CPVC (Chlorinated PolyvinylChloride) pipes of approved make conforming to IS-15778:2007 . with all necessary accessories, specials viz. socket,bend, tee, union, cross, elbo, nipple, longscrew, reducingsocket, reducing tee, short piece etc. fitted with holder batsclamps, including cutting pipes, fitting, fixing etc. completein all respect including cost of all necessary fittings asrequired,jointing materials in any position above ground.(Payment will be made on the centre line measurements oftotal pipe line including all specials. No separate paymentwill be made for accesories, specials.(a) For Exposed WorkFor exposed work(i) CPVC Pipes Class-I,SDR-11 15 mm dia. |
| 29 | Supplying, fitting and fixing bib cock or stop cock.Polythene Bib Cock/ Stop Cock (HD) with metal inlet(EMCO/ ATLAS or equivalent). 15 mm. |
| 30 | Supplying PVC water storage tank of approved quality with closed top weith lid (Black) - Multilayer. 1000 litre capacity. |
| 31 | Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. Brackets on 75 mm X 75mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30mm dia, approved quality P.V.C.waste pipe with C.P. nut 32mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P.nut including mending good all damages and painting the brackets with two coats of approved paint.450 mm x 300 mm size. |
AI Tender Summary
Tender Timeline
Sep 30, 2024
11:30 IST
Tender Published
Tender notice published.
CompletedOct 07, 2024
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 10, 2024
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender