Power Government Departments Closing in 0 days TDR #45349864

Tender For Resurfacing Of Roads In Hwp (K) Plant Site Phase Iv

Issued by Government Departments · Chittorgarh, Rajasthan
Tender Value
71.65 Lakhs
Estimated cost
Bid Submission
07 Oct 2024
0 days left
EMD
1.43 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Chittorgarh → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender For Resurfacing Of Roads In Hwp (K) Plant Site Phase Iv; 1 Providing and applying tack coat using bitumen emulsion conforming to IS:8887, using emulsion on bituminous surface @ 0.25kg/sqm pressure distributer etc. including preparing the existing road surface by removing all kinds of unwanted, foreign and loosely stuck materials using manual /mechanical means including scrubbing with hard wire brushes, brooming, collecting and disposing off the unserviceable material followed by intensive application of high pressure (@ 4 - 6 Kg. /Sq.M) compressed air jetting for removing all kind of dirt / dust etc.allcomplete as per the specifications and direction of Engineer-In-Charge. 2 Providing, Laying and Rolling open graded Premix Carpet produced through hot mixing of stone aggregate ( size conforming to Section: 500 of MORT&HSpecifiactions) with bitumen of specified source and specifications (VG-30 Grade conforming to IS: 73 from Indian Oil Corporation) @ 5.0 % by weight of Total Mix in Automated Hot Mix Plant (having provision for verifying weights and temperatures of individual ingredient as well hot-mix) in specified thickness, transporting the hot mix to work site, laying with Paver Finisher of appropriate width and consolidated with 8-12 MT road roller to achieve the desired compaction complete,followed by finishing with 8-12 MTvibratory roller for bringing the finished surface to true gradient , camber, straight edge etc. all complete as per Section: 500 of MORT& H specification, drawings, Technical specificationsand direction of Engineer In Charge. Note: Pre-qualification and acceptance of all the contractors eqipments by HWP(K) for their working condition, capacity, adequacy for work etc. shall be mandatory before deployment at works 3 Providing, Laying and Rolling Premixed Seal Coat as per section 500 of MORT&H Specification in 10mm compacted thickness by using paver Finisher of suitable width using hot mix of fine aggregate – bitumen (fine aggregate passing 2.36 mm sieve and retained on 180 micron sieve, mixed with bitumen of grade VG-30 conforming to IS – 73 source from Indian Oil Corporation) with Bitumen content of 6.0% by weight oftotal mix, evenly mixed in hot mix plant, consolidating with 8-12 MT roller and finished with 8-12 MT Vibratory roller to a uniform thickness surface including spraying the rock dust of specified fineness (as per section 500 of MORTH specification) liberally on the surface and brooming/ cleaning the surface followed by fanning with compressed air for removing all loose dirt and foreign material etc. complete as per specification and direction of Engineer-in-charge.) Note:1. Pre- Qualification and acceptance of all the contractor’s equipments by HWP(K) for their working condition, capacity, adequate for work etc. shall be mandatory before deployment at works.2. Contractor shall lay the seal coat with in 1-2 days after completion of laying & rolling of the pre mix carpet otherwise contractor shall apply tackcoat while doing seal coat at his own cost and no loss whatsoever on this account will be entertained by the department. 4 Providing and applying100mm wide and 2.5 mm thick road marking strips (retro-reflective) on the both side/Edges/Center line of theroad, of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications. (Thermoplastic material Automark/ Asian or any other equivalant make conforming to Section: 800 of MORT&H specification for hot applied thermoplastic road making shall be used) 5 Providing and fixing retro- reflective Glow studs of size 100x20 mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/-5) degress to base .The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge. 6 Providing and fixing solar glow studs of size 125mm x 125mm x 25mm (with a shank of 65mm) made of Aluminum-alloy shell having 100% water proof design according to IP67, high Efficiency Mono-Crystalline Solar Panel 2.4 V / 0.3 Watt & One Ni-Mh or NI-cd Rechargeable Battery (1.2V / 1600 MA) with Six Super Bright LEDs of 10,000 to 18,000 mcd (Millicandela) having a view Distance upto 1000 meters & Flash Rate of 2Hz or as directed by EIC with bearable Weight ofapprox 10 Tons in yellow, red, blue, green or white colour, it should have working time of 3 to 4 days after fully charged battery with charging time of 5 to 6 hours from direct sun light & working temp of 10 to 75 degree centigrade, Unbreakable poly carbonate clear facing design having provision of automatically turns on at night and turns off at dawn etc. complete as directed by EIC.The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge.

BOQ

Name of Work: “Resurfacing of Roads in HWP (K) Plant Site Phase IV.\"
Sl. No. Item Description
1Providing and applying tack coat using bitumen emulsion conforming to IS:8887, using emulsion on bituminous surface @ 0.25kg/sqm pressure distributer etc. including preparing the existing road surface by removing all kinds of unwanted, foreign and loosely stuck materials using manual /mechanical means including scrubbing with hard wire brushes, brooming, collecting and disposing off the unserviceable material followed by intensive application of high pressure (@ 4 - 6 Kg. /Sq.M) compressed air jetting for removing all kind of dirt / dust etc.allcomplete as per the specifications and direction of Engineer-In-Charge.
2Providing, Laying and Rolling open graded Premix Carpet produced through hot mixing of stone aggregate ( size conforming to Section: 500 of MORT&HSpecifiactions) with bitumen of specified source and specifications (VG-30 Grade conforming to IS: 73 from Indian Oil Corporation) @ 5.0 % by weight of Total Mix in Automated Hot Mix Plant (having provision for verifying weights and temperatures of individual ingredient as well hot-mix) in specified thickness, transporting the hot mix to work site, laying with Paver Finisher of appropriate width and consolidated with 8-12 MT road roller to achieve the desired compaction complete,followed by finishing with 8-12 MTvibratory roller for bringing the finished surface to true gradient , camber, straight edge etc. all complete as per Section: 500 of MORT& H specification, drawings, Technical specificationsand direction of Engineer In Charge. Note: Pre-qualification and acceptance of all the contractor\"s eqipments by HWP(K) for their working condition, capacity, adequacy for work etc. shall be mandatory before deployment at works
3Providing, Laying and Rolling Premixed Seal Coat as per section 500 of MORT&H Specification in 10mm compacted thickness by using paver Finisher of suitable width using hot mix of fine aggregate – bitumen (fine aggregate passing 2.36 mm sieve and retained on 180 micron sieve, mixed with bitumen of grade VG-30 conforming to IS – 73 source from Indian Oil Corporation) with Bitumen content of 6.0% by weight oftotal mix, evenly mixed in hot mix plant, consolidating with 8-12 MT roller and finished with 8-12 MT Vibratory roller to a uniform thickness surface including spraying the rock dust of specified fineness (as per section 500 of MORTH specification) liberally on the surface and brooming/ cleaning the surface followed by fanning with compressed air for removing all loose dirt and foreign material etc. complete as per specification and direction of Engineer-in-charge.) Note:1. Pre- Qualification and acceptance of all the contractor’s equipments by HWP(K) for their working condition, capacity, adequate for work etc. shall be mandatory before deployment at works.2. Contractor shall lay the seal coat with in 1-2 days after completion of laying & rolling of the pre mix carpet otherwise contractor shall apply tackcoat while doing seal coat at his own cost and no loss whatsoever on this account will be entertained by the department.
4Providing and applying100mm wide and 2.5 mm thick road marking strips (retro-reflective) on the both side/Edges/Center line of theroad, of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications. (Thermoplastic material Automark/ Asian or any other equivalant make conforming to Section: 800 of MORT&H specification for hot applied thermoplastic road making shall be used)
5Providing and fixing retro- reflective Glow studs of size 100x20 mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/-5) degress to base .The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge.
6Providing and fixing solar glow studs of size 125mm x 125mm x 25mm (with a shank of 65mm) made of Aluminum-alloy shell having 100% water proof design according to IP67, high Efficiency Mono-Crystalline Solar Panel 2.4 V / 0.3 Watt & One Ni-Mh or NI-cd Rechargeable Battery (1.2V / 1600 MA) with Six Super Bright LEDs of 10,000 to 18,000 mcd (Millicandela) having a view Distance upto 1000 meters & Flash Rate of 2Hz or as directed by EIC with bearable Weight ofapprox 10 Tons in yellow, red, blue, green or white colour, it should have working time of 3 to 4 days after fully charged battery with charging time of 5 to 6 hours from direct sun light & working temp of 10 to 75 degree centigrade, Unbreakable poly carbonate clear facing design having provision of automatically turns on at night and turns off at dawn etc. complete as directed by EIC.The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge.

AI Tender Summary

OUR REF NO 45349864
AUTHORITY Government Departments
TENDER VALUE 71.65 Lakhs
LAST DATE 07-10-2024
Authority
Authority Name Heavey Water Board
Work Description Tender For Resurfacing Of Roads In Hwp (K) Plant Site Phase Iv; 1 Providing and applying tack coat using bitumen emulsion conforming to IS:8887, using emulsion on bituminous surface @ 0.25kg/sqm pressure distributer etc. including preparing the existing road surface by removing all kinds of unwanted, foreign and loosely stuck materials using manual /mechanical means including scrubbing with hard wire brushes, brooming, collecting and disposing off the unserviceable material followed by intensive application of high pressure (@ 4 - 6 Kg. /Sq.M) compressed air jetting for removing all kind of dirt / dust etc.allcomplete as per the specifications and direction of Engineer-In-Charge. 2 Providing, Laying and Rolling open graded Premix Carpet produced through hot mixing of stone aggregate ( size conforming to Section: 500 of MORT&HSpecifiactions) with bitumen of specified source and specifications (VG-30 Grade conforming to IS: 73 from Indian Oil Corporation) @ 5.0 % by weight of Total Mix in Automated Hot Mix Plant (having provision for verifying weights and temperatures of individual ingredient as well hot-mix) in specified thickness, transporting the hot mix to work site, laying with Paver Finisher of appropriate width and consolidated with 8-12 MT road roller to achieve the desired compaction complete,followed by finishing with 8-12 MTvibratory roller for bringing the finished surface to true gradient , camber, straight edge etc. all complete as per Section: 500 of MORT& H specification, drawings, Technical specificationsand direction of Engineer In Charge. Note: Pre-qualification and acceptance of all the contractors eqipments by HWP(K) for their working condition, capacity, adequacy for work etc. shall be mandatory before deployment at works 3 Providing, Laying and Rolling Premixed Seal Coat as per section 500 of MORT&H Specification in 10mm compacted thickness by using paver Finisher of suitable width using hot mix of fine aggregate – bitumen (fine aggregate passing 2.36 mm sieve and retained on 180 micron sieve, mixed with bitumen of grade VG-30 conforming to IS – 73 source from Indian Oil Corporation) with Bitumen content of 6.0% by weight oftotal mix, evenly mixed in hot mix plant, consolidating with 8-12 MT roller and finished with 8-12 MT Vibratory roller to a uniform thickness surface including spraying the rock dust of specified fineness (as per section 500 of MORTH specification) liberally on the surface and brooming/ cleaning the surface followed by fanning with compressed air for removing all loose dirt and foreign material etc. complete as per specification and direction of Engineer-in-charge.) Note:1. Pre- Qualification and acceptance of all the contractor’s equipments by HWP(K) for their working condition, capacity, adequate for work etc. shall be mandatory before deployment at works.2. Contractor shall lay the seal coat with in 1-2 days after completion of laying & rolling of the pre mix carpet otherwise contractor shall apply tackcoat while doing seal coat at his own cost and no loss whatsoever on this account will be entertained by the department. 4 Providing and applying100mm wide and 2.5 mm thick road marking strips (retro-reflective) on the both side/Edges/Center line of theroad, of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications. (Thermoplastic material Automark/ Asian or any other equivalant make conforming to Section: 800 of MORT&H specification for hot applied thermoplastic road making shall be used) 5 Providing and fixing retro- reflective Glow studs of size 100x20 mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/-5) degress to base .The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge. 6 Providing and fixing solar glow studs of size 125mm x 125mm x 25mm (with a shank of 65mm) made of Aluminum-alloy shell having 100% water proof design according to IP67, high Efficiency Mono-Crystalline Solar Panel 2.4 V / 0.3 Watt & One Ni-Mh or NI-cd Rechargeable Battery (1.2V / 1600 MA) with Six Super Bright LEDs of 10,000 to 18,000 mcd (Millicandela) having a view Distance upto 1000 meters & Flash Rate of 2Hz or as directed by EIC with bearable Weight ofapprox 10 Tons in yellow, red, blue, green or white colour, it should have working time of 3 to 4 days after fully charged battery with charging time of 5 to 6 hours from direct sun light & working temp of 10 to 75 degree centigrade, Unbreakable poly carbonate clear facing design having provision of automatically turns on at night and turns off at dawn etc. complete as directed by EIC.The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge.
Basic Detail
Tender No HWPK/CIVIL/2024/120
Bidding Type Tender
Location
City Chittorgarh
State Rajasthan
Key Dates
Publish Date 21 Sep 2024
Submission Date 07 Oct 2024
Open Date 15 Oct 2024
Finance
Tender Value 71.65 Lakhs
Tender Fee Ref. Documents
EMD 1.43 Lakhs
Exemption Not Available
Document List
Guidelinesforetenderingin_1.pdf
MORTHSpecifications.pdf
ScheduleF2024120.pdf
SefetyguideforH2Ssafety.pdf
ff69c0e8-cf42-4bcc-8e6a-bc5e37ce3ce8.html
AERBSafetyGuide.pdf
APPENDIX2024120.pdf
BOQ_868926.xls
GCCHWPK.pdf
SOQ2024120.pdf
TenderdocumentCIVIL2024120.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Sep 21, 2024
11:30 IST

Tender Published

Tender notice published.

Completed
Oct 07, 2024
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Completed
Oct 15, 2024

Bid Opening Date

Technical bids will be opened and evaluated.

Completed

Tender Documents

Download All (ZIP) ↓
pdf

Guidelinesforetenderingin_1.pdf

pdf

MORTHSpecifications.pdf

pdf

ScheduleF2024120.pdf

pdf

SefetyguideforH2Ssafety.pdf

html

ff69c0e8-cf42-4bcc-8e6a-bc5e37ce3ce8.html

pdf

AERBSafetyGuide.pdf

pdf

APPENDIX2024120.pdf

xls

BOQ_868926.xls

pdf

GCCHWPK.pdf

pdf

SOQ2024120.pdf

pdf

TenderdocumentCIVIL2024120.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender