|
| 1 | Excavation in foundation and trenches etc. in earth work in all kind of soil such as pick work jumper work,saturated soil including bailing or pumping out water, blasting soft/hard rock, chiseling soft/hard rock where blasting is prohibited in all lifts including trimming and dressing of sides,levelling ofbed, stacking the excavated soil clear from the edge of excavation and then returning the excavated soil in 15cm. layers including consolidating each deposited layer by ramming , watering and then disposing of all surplus excavated soil as directed in all leads/lifts and shoring strutting,timbering and dewatering where ever required as per direction of the Engineer-in-charge. |
| 2 | Excavation in drains and channels etc, in earth work including dressing of sides and bed and disposal of excavatted earth up to a lead of 20 mtrs . In pick work. |
| 3 | Providing and laying cement concrete 1:4:8(1cement:4sand:8 graded stone aggregate of 40mm nominal size) and curing complete excluding cost of form work in in foundation and plinth including all leads and lifts. |
| 4 | Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a rough finish including centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4mtrs.and removal of the same for in situ reinforced concrete and plain concrete work includingall leads and lifts: |
| 5 | Vertical surfaces such as walls (any thickness)portions and the like including attached pilaster buttresses plinth and string course and the like |
| 6 | Flat surface such as soffits and suspended floors, roofs, landings and the like: Floors etc. up to 200mm in thickness within all leads and lifts |
| 7 | In column/ pillar, posts, square, polygonal in plan |
| 8 | Providing and laying reinforcement cement concrete 1:1 1/2:3(1cement:1 1/2 sand: 3graded stone aggregate of 20mm nominal size)and curing complete excluding cost of form work and reinforcement for reinforced concrete work in :- |
| 9 | Walls (any thickness) but not less that 0.10 Mtrs.thick including attached pilasters buttresses plinth and string course from top of foundation upto floor two levels. |
| 10 | Suspended floors, roofs, landings, shelves and their supports balconies, beams girders bressumers and cantilevers upto floor two levels |
| 11 | In Base |
| 12 | Providing,laying tor steel reinforcement for RCC work including bending, binding and placing in position i /c binding wire complete up to floor two level complete within all lead & liftsand to the entire satisfaction of the Engineer-in-Charge. |
| 13 | Steel work welded in built up sections,trusses & framed work i/c cutting,hoisting & fixing in position & applying a priming coat of red paint :-In grating, framed ,guards,bars,ladders, railing,brackets & similar works with in all leads and lifts as per the entire satisfaction & direction of the Engineer Incharge |
| 14 | Providing and fixing chain pully 5 Tonne capacity with its allied accessories complete as per the direction of Engineer in charge. |
| 15 | Random Rubble masonry /polygonal rubble un-coursed /brought two coat with hard stone of approved quality in foundation and plinth including leveling up cement concrete 1:6:12(1cement:6sand:12graded stone agg.20mm nominal size) in plinth level/super structure. with cm 1:6 (1cement :6sand) including all leads and lifts |
| 16 | Boulder filling behind the R/Wall and sides of abutment as per the direction of Engineer in charge. |
| 17 | Cutting in earth work and disposal of excavted earth up to lead of 20 mtrs |
| 18 | 6 mm cement plaster to ceiling in cement mortar 1:3 ( 1 cement : 3 sand). |
| 19 | Providing wood work in frames of doors and windows and clearestory windowsand other frames wrought, frammed and fixed in position.complete in all respect (2nd class deodar wood). |
| 20 | Providing and fixing pannelled glazed or pannelled and glazed shutters for doors wondows and clearstory windows including black enamelled iron butt hings with necessary screws 45 mm thick ( 2nd class Deodar wood). |
| 21 | Applying priming coat on new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil,greese,dirt and other foreign matters,sand papering and knotting.Ready mixed paint brushing wood primer pink. as per direction & satisfaction of the Engineer- in- chargeupto all lead & lifts. |
| 22 | Painting two coats ( Excluding priming coat) on new wood and wood based surface with ready mixed paint, brushing to give an even shade including cleaning oil, grease, dirt and other foreign sand papering and stopping:-Ready mixed paint other than white as per direction & satisfaction of the Engineer- in- chargeupto all lead & lifts. |
| 23 | Finishing wall with water proofing cement paint of approved brand and manufacture and ofrerquired shade on undecorated wall surfaces (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials complete within all lead & liftsand to the entire satisfaction of the Engineer-in-Charge. |
| 24 | Providing and laying cement concrete 1:1 1/2:3(1cement:1 1/2 sand: 3graded stone aggregate of 20mm nominal size)and curing complete excluding cost of form workand re-inforcemnment for reinforced concrete work in :- RCC slab |
| 25 | Wiring for light point / fanpoint /exhaust fan /call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable inPVC casing & capping and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. |
| 26 | Group C. |
| 27 | Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit along with 1 No.HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required. |
| 28 | 2x1.50 Sq. mm. |
| 29 | 2x4.00 Sq. mm. |
| 30 | Supplying and fixing 3 pin 5/6 amps socket outlet on the exisits switch box/covers including connections etc required. |
| 31 | Supplying and fixing 2 way 5/6 amps tumbler/piano type switch on the existingswitch box on the switch/cover including connections etc required. |
| 32 | Supplying and fixing 3 pin 15/16 amps socket outlet on the exisits switch box/covers including connections etc required. |
| 33 | Supplying and fixing 2 way 15/16 amps tumbler/piano type switch on the existingswitch box on the switch/cover including connections etc required. |
| 34 | Supplying and fixing ceiling rose on existing juction box/wooden block including connections etc as required. |
| 35 | Supplying and fixing plain pandent with 16/20 mm twin twisted, flexible PVC insulated copper cable and backelite pendant holder including connections etc as required. |
| 36 | Supplying and erection of 5 Amps to 32 Amps rating 240volts L-series miniature circuit breaker of following poles in the existing MCBDB complete with connections testing and commissioning etc as required Cat-A Single. |
| 37 | Providing installation testing and commissioning of ceilling fan and regulator i/c wiring the down rod of standard length ( upto 30 cm with 1.5 Sqmm PVCinsluted copper conductor single core cable etc as required ceiling fan including providing and fixing phenolic laminated sheet cover on the fan box and earting etc as required :- |
| 38 | Ceiling fan |
| 39 | Providing and fixing of Syska make LED tube lights G-20 watt including cost of fixing at site complete job in all leads and lifts. |
| 40 | Providing and fixing LED bulb 9 watt complete in all respect in all leads and lift. |
| 41 | Providing, installation testinf and commisioning of two rod heaters. |
| 42 | Providing and fixing two core service wire 6 Sq mm thick in all leads and lifts. |
| 43 | Providing and laying cement concrete 1:5:10(1cement:5sand:10 graded stone aggregate of 40mm nominal size) with 15% plum and curing complete excluding cost of form work in retaining walls/breast walls, the size of plums shall usually be 150mm to 300mm as per H.P.P.W.D specification including all leads and lifts |
| 44 | Dressing of bed and preparation of sub grade for linning in pick work. |
| 45 | Dressing of sides andpreparation of sub grade for linning in pick work. |
| 46 | Cement conc lining 15 cm thick or less for irrigation channels using 1:3:6 as per direction of Engineer in charge. |
| 47 | Hand mixed cement conccrete linning in bed. |
| 48 | Hand mixed cement conccrete linning on sides. |
| 49 | Extra allowance for form work in concrete linning in sides. |
| 50 | Removal of all kind of soil, sand,aggregate, boulder from existing storage tank, disposing of unserviceable material and stacking the serviceable material with in a lead of 20 mtrs and lifts upto 3.00 mtrs in all leads and lifts. |
| 51 | Providing, laying and Butt welding of MSERW pipe as per standard elecrical code upto date clatest ammendments at least 2-3 layers as site requirement including cutting welding etc with in all leads and lifts as per the satisfactory of Engineer in charge. MSERW pipe 200mm dia |
| 52 | Supplying and errection of submersible pump set of KSB/Calama.Johnston/SU/Kirlosker or JSV approvedmake confirming to BIS:8034-1976 or latest suitable for lifting water ( latest up to date ammendments) fitted with bronze inpellers/suitable alloy. The pump should be fitted with free flow impellers of bronze/suitable alloys directly coupled to squirrel case electric induction motor of same make as ( manufacturer standard) cinforming to BIS: 9283-1979 ( latest with upto date ammendments) and totally water proof for sumersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearing & providing with stainless steel thrust bearing plate to with stan vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard errection clamps, manufacturer cable clips & depth gauge etc.Submersible pump ( 2x10 = 20 HP), Discharge = 16.65 LPS each pump , Total Head 24.71 mtr (Phase - II) |
| 53 | Supplying and errection of submersible pump set of KSB/Calama.Johnston/SU/Kirlosker or JSV approvedmake confirming to BIS:8034-1976 or latest suitable for lifting water ( latest up to date ammendments) fitted with bronze inpellers/suitable alloy. The pump should be fitted with free flow impellers of bronze/suitable alloys directly coupled to squirrel case electric induction motor of same make as ( manufacturer standard) cinforming to BIS: 9283-1979 ( latest with upto date ammendments) and totally water proof for sumersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearing & providing with stainless steel thrust bearing plate to with stan vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard errection clamps, manufacturer cable clips & depth gauge etc.Submersible pump ( 2x10 = 20 HP),Discharge = 11.56 Lps Each , Total Head 34.13 mtr (Phase - I) |
| 54 | Laying jointing testing and carriage in trenches HDPE pipe 10 kg/cm working pressure polythene pipe high densit confirming to IS 4984-1972 complete with compression type fitting. (LR) |
| 55 | 160 mm dia HDPE pipePE-80, PN-4 |
