Development Of Park In Kangoi Under Nagar Parishad Mihijam, Mihijam-Jharkhand

TDR : 45212308

Tender Notice
BOQ

Expired

Mihijam , Jharkhand

Tender Brief : Development Of Park In Kangoi Under Nagar Parishad Mihijam

Document Fees
₹ 10000 /-

EMD
₹ 200500.0 /-

Tender Value
Refer document

Submission Date
18-09-2024

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Earth Work inexcavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I
2	Extra for earth work in hard soil as per specification and direction of E/I. (vide classfication of soil item - B)
3	Earth filling infoundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earthobtainedfrom excavation offoundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I.(mode of measurement compacted volume)
4	Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including\" cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).
5	Clearing grass and removal of rubbish uptp a distance of 50 meters outside the periphery of the area
6	Providing and laying damp-proof course 40mm thick with cementconcrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)
7	Making Plinth protection 50mm thick of cement concrete 1;3;6(1 cement 3coarse sand 6; graded stone aggregate 20mm nominal size ) over 75mm bad by dry brick ballast 40mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.
8	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)
9	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand ) : 8 graded stone aggregate 40 mm nominal size )
10	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinfforcement - All work up to plinth level, 1:1.5:3 (1 cement : 1.5 coarse sand {zone-lll}: 3 graded stone aggregate 20 mm nominal size)All works upto plinth level
11	Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sandizone-Iil} : 3 graded stone aggregate 20 mm nominal size).All works above plinth level upto floor V level
12	Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings,balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinthlevel up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
13	Add for using extra cement in the items of design mix over and above the specified cement contenttherein.
14	Centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete
15	Centering and shuttering including strutting, propping etc. and removal of form for.Suspended floors, roofs, landings, balconies and access platform
16	Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers
17	Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts
18	Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like,Edges of slabs and breaks in floors and walls.
19	Under 20 cm wide
20	Providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL)
21	Providing Tor steel reinforcement of 10mm, rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL)
22	Providing Tor steel reinforcement of 12mm. to 25 mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMTFe 500 (only vailid for TATA (TISCON), SAIL,JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))
23	Dry Lean Cement Concrete Sub- base (Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing.)
24	Providing designation 75 A brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.
25	Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.
26	Providing designation 100A brick work with flyash lime brick (FLAG) confirming to IS 12894-1990 (9\"x4.5\"x3\") in C.M. (1:4) in super structure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints costs of screening materials, scaffolding, raking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I.
27	Providing Designation 100AB/W with Fly Ash Lime Brick (FALB) conforming to IS 12894-1990 (9\"x4.5\"x3\") in cement mortar (1:6) in Superstructure with clean coarse sand of F.M. 2 to 2.5 including 10mm thick mortar joints,cost of screening, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.
28	Providing designation 112mm thick reinforcement designtion 100 A brick work with fly ash lime brick(FLAG) confirming to IS 12894-1990 (9\"x4.5\"x3\") in C.M. (1:4) in supertructure with approved quality ofclean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffoliding raking out joints to15mm depth curing taxesand royalty ( but excluding theb cost of reinforcement) all complete as perbuilding specification and direction of E/I.
29	Extra for providing & placing in position 2 no 6mm dia ms bar every 3rd corse of half brick masonry
30	Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I
31	Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in charkha indoors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clampscomplete including application of two coats of wood preservative of approved quality on the surfacebutting walls and lintels all complete as per building specification and direction of E/I.
32	Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).
33	Supplying, fitting and fixing 30mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.
34	Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.)
35	Supplying, fitting and fixing M.S. grill gate with M.S. grill made of 20X6mm M.S. flats or 16mm M.S. square bars fitted on 25X25X6mm M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.
36	Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer all complete.
37	Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
38	Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.
39	Providing and laying 1st quality Ceramic glazed wall tiles thickness to be specified by the manufacturer) in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing polishing and cost of curing, taxes and royalty all complete as per building specification and direction of E/I.
40	Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete.
41	Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade.Area of slab over 0.50 sqm.
42	Providing 12mm cement mortar (1:3) with clean coarse sand of F.M. 1.5 with floating coat of neat cement in skirting including rounding of junctions with floor, curing, taxes and royalty all complete as per building specification and direction of E/I.
43	Providing and laying 25mm thick. Kotah stone slab flooring of approved size, texture and colour over 19mm thick base of lime mortar (1:1:1) (lime putty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royality all complete as per building specification and direction of E/I.(iv) 600 x 600 mm size
44	Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. 600 x 600 mm size
45	Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge
46	Providing and laying factory made chamfered edge Cement Concretepaver blocks in footpath, parks, lawns, drive ways or light trafficparking etc, of required strength, thickness & size/ shape, made bytable vibratory method using PU mould, laid in required colour &pattern over 50mm thick compacted bed of sand, compacting andproper embedding/laying of inter locking paver blocks into the sandbedding layer through vibratory compaction by using plate vibrator,filling the joints with sand and cutting of paver blocks as per requiredsize and pattern, finishing and sweeping extra sand. complete all asper direction of Engineer-in-Charge.60mm thick cement concrete paver block of M-35 gradewith approved colour, design & pattern.
47	Providing average 150 mm thick dry rammed koha beaten to 112 mm. (Compacted with water ) made of well burnt or jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blending the top with cement mortar (1:10) all complete as per building specification and direction of E/I.
48	Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.
49	Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curingwithall leadsand liftsof water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.
50	Providing 6mm cement plaster (1:4) in celling with clean coarse sand of F.M. 1.5 including screening,curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per buildingspecification and direction of E/I.
51	Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/I.
52	Providing 19mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico orany other approved water proofing compound including screening, curing with all leads and lifts of water,scaffolding taxes and royalty all complete as per building specification and direction of E/I.
53	Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 SQM) over and including priming coat of exterior primer applied @ 2.20kg/10 SQM
54	Providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered wallsurface to prepare the surface even and smooth complete.
55	Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification)
56	Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.
57	Providing two coat of oil bound distemper of approved shade and make over a primer coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding, washing floors and taxes all complete as per building specification and direction of E/I.
58	Providing and fixing at or near ground level precast cement concretein kerbs, edgings etc. as per approved pattern and setting In positionwith cement mortar 1:3 (1 Cement : 3 coarse sand), including the costof required centering, shuttering complete.
59	Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement :4 coarse sand) mixed with 2% integral water proofing compound
60	Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :.In 75x75 mm deep chase
61	Water proofrng for Old and New Roof Slab :- Providing and laying water prooflng treatment on roof slab by applying two Component, factory a designed ready to use, acrylic modified flexible material applied with brush,roller or spraywaterproofi ng coating as per manufacturer specification-With following steps :-all corners shall be charfered with 150mm X 150 mm fillet. The rain water outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - the peripheral gaps between pvc pipe outlet and concrete surface should be packed properly with rich concrete and the peripheral mouth to be sealed with moisture insensitive epoxy putty of Sika lndia Pvt.Ltd / IVIYK Schomberg / Dr FixiUFosroc .For the purpose of measurement the entire treated surface will be measured.\"(e)Groove of PCC surface should be filled with Polysulphide Sealant (Paid Separately) Brand - Sika lndia Pvt Ltd / MYK Schomberg / Dr Fixit/Fosroc
62	Covering of treated surface wrth PCC :- Providing 50 mm thick Cement Concrete M20 (1:1.5:3) raintaining slope in alternate 2 mIx 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and clcaned sand of F M 2 5 io 3 including screening,shuttering,and mixing cerite nt c0ncrete in mixer with admixture of integral water proofing and placing rn position,strikirrg cLrring,t-a]glgnd royality all complete as per buildirrg specifictionJand direction of E/l.Panels that has been left should be casteci nextday.-lhere should be 6 mm gap between Panels.Brand- Sika *Plastocrate plus,MYK proof WP10, Fosroc- Conplast X421ic , Dr Frx,t Prdiproof LWr
63	Provrding and filling of Groove between 50 mm PCC Panels with Polyshlphide Sealant (Poring Grade)as per drawings and technical specifications and dii-ection of E in Charge (with 1B% GST).Brand:-Sika- Polysulphide, Fosroc-l-hioflex 600 Dr. Fixit Pidiseal PS(42P),MYK Seal PS or Euivallent
64	Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cementlaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.
65	Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
66	Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of :i) Ist course of applying cement slurry @ 4.4 Kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.ii) IInd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 Kg. per sqm of area.(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm.)
67	Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelingand dash fasteners to be paid for separately) :For fixed portion.Powder coated aluminum (minimumthickness of powder coating 50 micron)
68	For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately).Powder coated aluminum (minimumthickness of powder coating 50 micron)
69	Providing and fixing glazing in aluminum door, window, ventilatorshutters and partitions etc. with EPDM rubber / neoprene gasketetc. complete as per the architectural drawings and the directions ofengineer-in-charge . (Cost of aluminum snap beading shall be paidin basic item):With float glass panes of 5.5 mm thickness
70	Providing and fixing glazing in aluminum door, window, ventilatorshutters and partitions etc. with EPDM rubber / neoprene gasketetc. complete as per the architectural drawings and the directions ofengineer-in-charge . (Cost of aluminum snap beading shall be paidin basic item):With float glass panes of 8 mm thickness (weight notless than 20 kg/sqm)
71	Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia
72	Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.In Recharge Well (Лr²h)
73	Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-chargeIn Recharge Well
74	Supllying and matarials with lobour for construction inspection chamber of designation class 75b brick deep 600x450 internal diamention having 250mm wall thickness in cementmorter(1:6)including 12mm cement plaster (1:4)with punning on inside and cement plaster (1:6)with 600x450mm G.I. cover with frame (weight not less than 36k.g)in foundation and refilling all complete as per specification and direction of E/I.
75	Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg1 nos
76	Cost of Driling 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.(a) From 0.00 M to 50.00 M below G.L.
77	SAND(UPTO 20 KM LEAD)
78	CHIPS(UPTO 22 KM LEAD)
79	METAL (UPTO 22 KM LEAD)
80	BRICKS (UPTO (7+1) KM LEAD)
81	Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.(a) From 0.00 M to 50.00 M below G.L.
82	Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.(b) From 51.0 M to125.00 M
83	Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.(c) From126.0 M to150.00 M
84	Supplying, assembling, lowering and fixing in vertical position in borewell,unplasticizedPVCmediumwellcasing(CM)pipeof required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.200 mm nominal size dia
85	Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by \"V\" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge
86	Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:200 mm dia
87	Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.200 mm clamp
88	Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump.Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages2 HP
89	Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes , all complete job as per direction of E/I.
90	Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etcall complete job as per direction of E/I.
91	Supply fitting and fixing lowering 40 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.
92	Providing and fixing brass/C.I. stop cock of approved quality all complete as per specification and direction of E/I.15 mm dia
93	Providing and fixing G.M. non return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I.25 mm dia
94	Providing and fixing G.M. non return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I.32 mm dia
95	Making holes in walls for laying G.I. pipe and restoring the same after pipe laying as per specification and direction of E/I.125 mm thick wall
96	Making holes in walls for laying G.I. pipe and restoring the same after pipe laying as per specification and direction of E/I.250 mm thick wall
97	Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.Mirror (300 x 450mm)
98	Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.C.P. brass tower rail
99	Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.C.P. brass soap container medium quality with screw and hinges etc.
100	Supplying, fitting and fixing viterious white glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I. \"p\" trap 15 litres C.I. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair or viterous white glazed earthenware footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I.580mm long - With 12.5 lit. low level PVC cistern.In Each W.C.
101	Supplying, fitting and fixing 40mm highb viterous white glazed earthen E.W.C. with \"P\" trap of parry hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fitting with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stope cock of approved quality weight not less than 450 grams 15mm PVC alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic soild state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming all complete as per specification and direction of E/I.With \"P\" trap - 10.0 lit low level PVC Cistern.In Each W.C.
102	Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthen ware urinal of \"Hindustan \"Parry\" or any other approved I.S.S. make with 5 liters capacity C.I. automatic flushing cistern of reliance for any other I.S.S. approved make with all fittings with C.I. or R.S., brackets, standard size G.I. flush pipe with fitting clamps, 15mm, C.I. body brass spindle stop cock of approved quality weight not less than 400 grams, 15mm P.V.C./Alkthene pipe 450mm long with brass coupling at both ends and doing plumber joints including painting coat of red oxide cutting wall and floor making good the same etc. all complete as per specification and direction of E/I.(a)Flat back or Standing Cornar
103	Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approved make supported on pointed C.I. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms. 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.
104	Supplying materials and labours for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600 x 450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600 x 475mm G.I. Cover with frame (weight not leaa than 36 kg) alongwith earth work in exacavation and 80mm thick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.
105	Supplying NP2 R.C.C. hume pipe with colour as work site as per direction of E/I.150mm dia
106	Approved basic rates construction materials for preparation of schedule of rates only, (Material should conform to relevent B.I.S. specification). The rates are inclusive of all taxes, royalty, cess and carraige but exclusive of contractor\"s profit and overhead charges -Special type of C.P. Bath room fitting for V.I.P. buildings (JAL, Jaguar, Marc or equivalent mark) Pillar cock
107	Approved basic rates construction materials for preparation of schedule of rates only, (Material should conform to relevent B.I.S. specification). The rates are inclusive of all taxes, royalty, cess and carraige but exclusive of contractor\"s profit and overhead charges -Special type of C.P. Bath room fitting for V.I.P. buildings (JAL, Jaguar, Marc or equivalent mark. Angular Stopcock /2 way bib cock
108	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.75 mm diameter
109	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter
110	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Single tee without door - 75x75x75 mm
111	Single tee without door - 110x110x110 mm
112	75 mm bend
113	110 mm bend
114	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall.25 mm nominal outer dia Pipes
115	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall.32 mm nominal outer dia Pipes
116	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.15 mm nominal outer dia Pipes
117	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.20 mm nominal outer dia Pipes
118	Providing and placing on terrace (at all floor levels) polyethylene waterstoragetank,ISI:12701marked,withcoverandsuitablelockingarrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank.
119	Supplying and stacking of good earth at site including royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).
120	Supplying and stacking at site dump manure from approved source, including carriage up to 1.0 km (manure measured in stacks will be reduced by 8% for payment)Screened through sieve of IS designation 20 mm
121	Screened through sieve of IS designation 16 mm
122	Screened through sieve of IS designation 4.75 mm
123	Supplying and stacking of well decayed cow dung manure at site including royalty and carriage up to 1.0 km (cow dung manure measured in stacks will reduced by 8% for Payment)
124	Fine dressing of the ground
125	Mixing earth and sludge or manure in the required proportion specified or directed by the Engineer-in-charge
126	Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Engineer-in-charge (cost of sludge, dump manure and / or good earth to be paid separately).
127	Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts
128	Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)Holes 1.2 m diameter and 1.2 m deep
129	Holes 90 cm diameter and 90 cm deep
130	Holes 60 cm diameter and 60 cm deep
131	Holes 45 cm diameter and 45 cm deep
132	Complete maintenance of the entire garden features having as per yard stick in the gardenarea i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing,weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cuttingby lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide &fertilizers (whenever required) top dressing of lawn with good earth and manure andmaintenance of other garden related works as directed by office-in-charge (Cost of GoodEarth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawnmover and brush cutter with fuel and other T & P material/articles shall be provided by thecontractor.) and as per direction of officer in charge.
133	Delonix regia (Gulmohar / April fool)
134	Cassia fistula (Amaltash)
135	Dalbergia sissoo (Sheesham)
136	Pterospermum acerifolium (Makchund)
137	Ficus religiosa (peepal)
138	Ficus benghalensis (bargad / banyan)
139	Cestrum nocturnum (raat rani)
140	Saraca indica (Sita Ashok)
141	Azadirachta Indica (Neem)
142	Bauhinia purpurea (Kachnar)
143	Callistemon lanceolatus (Bottle brush)
144	Spathodea campanulata (rugtoora)
145	Plumeria alba (white champa)
146	Plumeria rubra (pink champa)
147	Lagerstroemia flosreginae (jarul)
148	Polyalthia longifolia (Ashok)
149	Tectona grandis (sal)
150	Tamarindus indica (Imli)
151	Mangifera indica (Mango)
152	Eugenia jambolana (Jamun)
153	Phyllanthus emblica (Amla)
154	foxtail palm
155	Bottle palm
156	Areca Palm
157	Traveller\"s palm
158	Bismarckia Palm
159	Phoenix palm
160	Buddha belly bamboo
161	Clerodendrum inerme (Volkameria inermis)
162	Ficus panda
163	Ficus benjamina Starlight (Ficus Starlight)
164	Gardenia jasminoides
165	Golden duranta
166	Hamelia patens
167	Hibiscus rosa-sinensis (udhul)
168	Raphis excelsa (lady palm)
169	Tecoma gaudichaudi(Yellow bells)
170	TMC dwarf (Chandani)
171	Canna dwarf
172	Rose
173	Topiary of Ficus Panda
174	Marigold jaffri
175	Dracaena
176	Alternanthera red
177	Chlorophytum comosum
178	Jatropha
179	Sprenger\"s asparagus (Foxtail fern)
180	Syngonium podophyllum (Syngonium butterfly)
181	Tradescantia pallida
182	Cynodon dactylon (doob grass)
183	Wiring for light point/ fan point / exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular switch, modular plate, suitable GI box etc as required.Group C
184	Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.
185	Wiring for light/ power plug with 4X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 2 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.
186	Wiring for circuit / submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required2x1.5sq mm + 1x1.5 sq mm earth wire
187	2x2.5sq mm + 1x2.5 sq mm earth wire
188	2x6 sq mm + 1x6 sq mm earth wire.
189	Supplying and fixing of following sizes of PVC conduit along with the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20mm dia
190	Supplying and fixing of following sizes of PVC conduit along with the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25mm dia
191	Supplying and fixing of following sizes of PVC conduit along with the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32mm dia
192	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps one way switch
193	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp one way switch
194	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amp 3 pin socket outlet
195	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/16 amp 6 pin socket outlet
196	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.4/5 Module (78mm x140mm x 50mm)
197	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (78mmX205mmx50mm)
198	Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)12 WayDouble Door
199	Supplying and fixing 6 Amp to 32 Amp rating 240 volts, 10 KA\"C\" Curve Miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc.,as required. 6 / 32 Amp Single Pole
200	Supplying and fixing 6 Amp to 32 Amp rating 240 volts, 10 KA\"C\" Curve Miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc.,as required. 50/63 Amp DP
201	Supplying and fixing of following rating double pole ( Single pole & neutral),240 volts, resudual current circuit breaker (RCCB), having a sensivity current 30 miliampere in the existing MCB DB complete with connections, testing & commissioning etc as required.63 Amps
202	Providing and fixing M.V. danger Notice plate of 200mm x 150 mmof made of mild steel, at least 2 mm thick and vitreous enamelded white on both side and with inscription in single red colour in front side as requird
203	Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) as required.
204	Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required
205	Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.
206	Supply of XLPE insulated PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts. (conforming toIS-7098. (Part-I).3.5 core,35 sq.mm.
207	2 core,10 sq.mm.
208	2 core,6 sq.mm.
209	Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm
210	Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Upto 35 sq. mm
211	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 x 6 sq. mm (19mm)
212	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 X 10 sq. mm (22mm)
213	Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 35 sq. mm (32mm)
214	Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.120 mm dia (OD-120 mm & ID-103 mm nominal)
215	Design, Manufacturing, Supply, installation, Testing & Commissioning of Outdoor Type Panel with Front & Back double door, Top canopy, Mounting on Floor M.S. Stand etctotally enclosed free standing type water, moisture, dust and vermin proof Sub Distribution Board made out of 2.0 mm thick CRCA sheet complete with followingequipments, includingammeter, ammeter selector switch, voltmeter, voltmeter selector switch, indicating lamps, CT\"s, internal wiring with suitablesize wires/ cable, interconnection, painting etc as required.INCOMING1 No 100 Amp FP Moulded Case Circuit Breaker (25 KA) with 100 Amp 4 Pole Contactor & Timer.1 No. Digital AVF Meter with inbuilt selector switch and CT\" & SP MCB.1 Set of phase indicating lamps.1 Set of ON/OFF indicating lamps with SP MCB.BUS BARS200 Amp FP aluminium busbar with coloured heat shrinkable sleeve.OUTGOING10 Nos. 25 Amp DP MCB(10 KA)03 Nos. 63 Amp FP MCB(10 KA)03 Nos. 63 Amp DP MCB(10 KA)
216	SITC of following rating recess / surface mounted LED round / square shape down light luminarie with pressure die cast housing for single phase supply voltage Luminarie shall be confirm to IS: 10322 part -5 / section -2 or IEC :62722 withh all neccesary accessories as required.Make:- Havells/Philips/Crompton/Wipro / India 12W LED Round Down Light (Surface )
217	SITC of following rating recess / surface mounted LED round / square shape down light luminarie with pressure die cast housing for single phase supply voltage Luminarie shall be confirm to IS: 10322 part -5 / section -2 or IEC :62722 withh all neccesary accessories as required.Make:- Havells/Philips/Crompton/Wipro / India 18 /20 W LED Round Down Light (Surface)
218	Bulk Head fitting with 9/10Watt LED.
219	S.I.T.C of following rating surface mounted LED Tube Lighting Fitting Suitable for 230V 50 Hz, Single Phase Supply etc. complete as required.10/12 W LED Tube Light
220	S.I.T.C of following rating surface mounted LED Tube Lighting Fitting Suitable for 230V 50 Hz, Single Phase Supply etc. complete as required.20/22 W LED Tube Light
221	SITC of300 mm (12\") Exhaust fan (Metal body) suitable for single phase 230 volts, 50 Hz., AC supply complete with motor, louvers/shutters etc. complete as required. Make :- Usha/Crompton / Havells .
222	Supply of 20mtr. High mast in two section Construction 5355 grade as per BIEN 10 025 Top Dia 150mm, bottom dia 410mm, plate thickness 3mm,2Oside polygon, galvanisation as per BS EN ISO 146L, base plate dia 570mm, base plate thickness 25mm, GI single spike lighting protection, maximum wind speed 47 m/swith 8 nos foundation bolts of PCD 490mm TS 600/ 30mm dia/850 mm long. Luminaries carriage : Material for 50 NB ERW Class B - M.S. Pipe, dia of carriage ring 535mm (ID) with 6 arm, welded,2 sections having carrying capacity upto 12 luminaries. Trailing Cable : 5 core 4sq.mm. PVC flexible copPer conductor Winch/Power Tool : Double drum, SWL 750 kg with 1HP 6 pole single speed integral motor Rope : Grade A13131\"6,7 /19 construction, dia 6mm, BLC 2350 x 2 having 2 nos of continues roPe. Aviation obstmction light: twin dome aviation obstruction lights LEDtype as required. (But excluding Feeder Pillar)
223	For 20 mtr. High mast: ITC of the high mast and light fixture with thehelp of suitable tools and plans, wiring of luminaries with all Wiringmaterial like PVC insulate[Pvc sheathed flexible cable of suitlblbcopper conductor lugs, MCB and all labour & construction of shallow foundation with M25 grade concrete for the high mast considering safe soil bearing capacity of 10T / mhs sq. for 20 M High mast.
224	S.I.T.C of floowing rating LED Street lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protecdon) ln odsttng pole/pipe for supply voltage \WTIY AC, 50H2. Luminarie shall be confirm to IS: 1(E22 part-5/secdon-3 and shall be complete with all neccssary accessories as required.( LED FLOOD Light 240W)
225	Supply & Installation of DUSTBIN 100 Litres litres HDPE waste containers or rigid liners.Utility-Public (Mobile containers confirming IS: 12402).Material -HDPE.Bin Capacity (Volume) (Ltrs)-100 Litres.Wall -Non- Perforated.Lid -Swing type.Weight of Dustbin(Complete unit) (Grams)-12500.Gripping Provision-Both Frontal &Ventral.Dust Bin stand -With.No. of Compartments inthe Bin-Twin Bin.All complete work as per E/I.
226	Supply and Installation ofCast Iron Powder CoatingGarden Bench, Capacity 3 Seater NA(GARDEN BENCH 3 SEATER KB).Seating Capacity -3 Seater.Finsh-Powder Coating .Weight Bearing Capacity-110 kilogram.Side Frame Material-Cast Iron.Seat Material & Back Rest Material -Mild Steel Pipe 14 Gauge.Total Height -915 millimeter.Seat Height -401 millimeter.Width-450 millimeter.Total Area Required-1550 millimeter.All complete work as per E/I.
227	Supply and Installation ofOutdoor GymEquipments Leg Press Double.Type-Leg Press Double.User Weight ( Kg )-120 kilogram.Length -1000 millimeter.Width-650 millimeter Governing Specification for GI Pipes -BIS specification No IS 1161:2014, latest.Main Central Pipe-125 mm Nominal Bore G.I. Pipe.Main Central Pipe, Class as per IS 1239-Heavy.Movine Frame Pipe-40mm Nominal bore.Maximum User Weight-120 KG.Foot Rest Frame/ Foot Rest Hinging Pipe-32mm Nominal Bore G.I. Pipe.Foot Rest Frame Pipe, Class as per IS 1239-Heavy.MS Foundation Plate Thickness-12 millimeter.Foundation Pipes with anchoring-750mm deep GI Pipe, supported with M.S. Angle 25 X 25 X 4mm.Nominal Bore of Foundation Pipe-125mm.Galvanization of all Pipes-Zinc coating on the tubes shall be in accordance with IS 4736 latest..Bearings-Tapered Roller Bearing.Bearings shall be self lubricating and sealed for protection against Rain and dust etc-Yes.Seat and Back Rest-6mm thick, Fibre Reinforced plastic with uniform bending radius to avoid sharp edges.Foot Rest-Aluminum casting material.Thickness of closing caps -2 millimeter.All Plastic Components-U V stabilised, weather resistance.Paint// Finish-Powder Coated, UV resistant.Paint Coating Thickness (min )-80 micrometer.Instruction Plate-Stainless Steel, Size 150 X 230 X 0.7mm, with indelible printing.All complete work as per E/I.
228	Supply and Installation of SEASAW Jungle Rumble Play Zone.Design slides, serpentine Slides and covered slides material-Premium quality FRP (fibre reinforce plastic).Roofs -Premium quality FRP (fibre reinforce plastic).Bridges floor-Premium quality FRP (fibre reinforce plastic).Thickness of slides-3 mm.Thickness of roof-3 mm.Thickness of bridge floor-3 mm.Material for stairs, bridge railing, slides supports-25 mm (B class conforming to IS 1239 latest) PU coated with the layer of thickness of 60 microns.Material for supporting stands-25 mm (B class conforming to IS 1239 latest) PU coated with the layer of thickness of 60 microns.Design-As per representative image - uploaded at QR/Spcn-Product Structure-G.I pipe Stairs – open and closed FRP slider – FRP bridges with pipe railing – huts type FRP roof supported by G.I pipes.Dimension ± 10 mm-Length - 13500 mm X Width - 6500 mm X Height - 3250 mm.FRP sheets finish -G.P resin of 3 mm to 4 mm thickness applied above the surface of gel coat which is dully mixed with U.V stabilized pigment to provide resistance to ultra violet light degradation.GI pipe finish-PU paint over two coat of epoxy primer.All complete work as per E/I.
229	Supply and Installation of SWINGJungle Rumble Play Zone.Design slides, serpentine Slides and covered slides material-Premium quality FRP (fibre reinforce plastic).Roofs-Premium quality FRP (fibre reinforce plastic).Bridges floor -Premium quality FRP (fibre reinforce plastic)-Thickness of slides-3 mm.Thickness of roof-3 mm.Thickness of bridge floor-3 mm.Material for stairs, bridge railing, slides supports.25 mm (B class conforming to IS 1239 latest) PU coated with the layer of thickness of 60 microns.Material for supportingstands.25 mm (B class conforming to IS 1239 latest) PU coated with the layer of thickness of 60 microns.Design -As per representative image - uploaded at QR/Spcn.Product Structure -G.I pipe Stairs – open and closed FRP slider – FRP bridges with pipe railing – huts type FRP roof supported by G.I pipesDimension ± 10 mm-Length - 13500 mm X Width - 6500 mm X Height - 3250 mm.FRP sheets finish -G.P resin of 3 mm to 4 mm thickness applied above the surface of gel coat whichis dully mixed with U.V stabilized pigment to provide resistance to ultra violet light degradation.GI pipe finish-PU paint over two coat of epoxy primer.All complete work as per E/I.
230	Supply and Installation of KID REVOLVING Jungle Rumble Play Zone.Design slides, serpentine Slides and covered slides material-Premium quality FRP (fibre reinforce plastic).Roofs -Premium quality FRP (fibre reinforce plastic).Bridges floor-Premium quality FRP (fibre reinforce plastic).Thickness of slides-3 mm.Thickness of roof -3 mm.Thickness of bridge floor-3 mm.Material for stairs, bridge railing, slides supports-25 mm (B class conforming to IS 1239 latest) PU coated with the layer of thickness of 60 microns.Material for supporting stands-25 mm (B class conforming to IS 1239 latest) PU coated with the layer of thickness of 60 microns.Design-As per representative image - uploaded at QR/Spcn.Product Structure-G.I pipe Stairs – open and closed FRP slider – FRP bridges with pipe railing – huts type FRP roof supported by G.I pipes.Dimension ± 10 mm -Length - 13500 mm X Width - 6500 mm X Height - 3250 mm.Area for play zone -48 feet X 20 feet.FRP sheets finish -G.P resin of 3 mm to 4 mm thickness applied above the surface of gel coat which is dully mixed with U.V stabilized pigment to provide resistance to ultra violet light degradation.GI pipe finish -PU paint over two coat of epoxy primer.All complete work as per E/I.
231	Supply and Installation of Slide Ladder (Preschool Kit) Virgin Polycarbonate and Multi curve configuration.Slide ladder made up of virgin grade polyethylene plastic-Virgin Polycarbonate.Bolts quality (to provide greater stability to slide)-To provide as per approved advance sample.Overall length of the product (when assembled)-2415mm.Overall width of the product (when assembled)-965mm (Stare supporting base) and 432 mm (Sliding part).Overall height -1143 mm.Length of sliding part-1829 mm.Length of the stair panel-1 270 mm.Step rise of each stair-445 mm long.Minimum overall plastic weight of product-16 Kg.All complete work as per E/I.
232	Supply and Installation of Triple Twister ( Three standing) Twister - Outdoor Gym Equipment.Type-Triple Twister ( Three standing).Length-1400 millimeter.Width-900 millimeter.Height-1200 millimeter.Maximum User Weight-120 kilogram.Governing Specificationfor GI Pipes-BIS specification No IS 1239 ( Part 1 )- 2004, latest.Main Central Pipe-125 mm Nominal Bore G.I. Pipe.Main Frame Pipe, Class asper IS 1239-Heavy.Main Central Pipe ( As per Clause 3, of IS 1161 )Nominal Bore & WallThickness-125 mm NB with 4.5 mm Thickness.Grade Material as pertable2oflS1161-YSt 355.Standing/ Sitting TwisterFrame Pipe-50 mm Nominal Bore G.I.Pipe.Standing/ Sitting Twister Frame Pipe (As per Clause3, of IS 1161 ) NominalBore & Wall Thickness-50 mm NB with 4.5 mm Thickness.Grade Material as per table 2 IS 1161-YSt 355.Rotating Disk Support Pipe at Bottom Pipe-125 mm Nominal Bore G.I. Pipe.Rotating Disk SupportPipe (asper IS 1161 ) asper Clause 3, NominalBore & Wall Thickness-125 mm NB with 4.5 mm Thickness125 mm NB with 4.5 mm Thickness-40 mm Nominal bore G.I. pipe.Foundation Pipes withanchoring-750mm deep GI Pipe, supported with M.S. Angle 25 X 25 X 4mm.Nominal Bore ofFoundation Pipe-150mm.Foundation Pipe Pipe ( as
233	Supply and Installation of Parallel Bar of 750mm deep GI Pipe, supported with M.S. Angle 25 X 25 X 4mm Parallel Bar - Outdoor Gym Equipment.Type-Parallel Bar/ Double Bar consisting of two frames with each frame consisting of one Horizontal bar and two vertical bars.Governing Specification for GI Pipes-BIS specification No IS 1239 ( Part 1 )- 2004, latest.Vertical/ Standing Pipes-100 mm Nominal Bore G.I. Pipe.Vertical/ Standing Pipes, Class as per IS 1239-Heavy.Vertical/ StandingPipe (as per Clause 3 of IS 1161), Nominal Bore & Wall Thickness-100 mm NB with 3.6 mm Thickness.Horizontal Pipe-32 mm Nominal Bore G.I. Pipe.Horizontal Pipe ( As per Clause 3, of IS 1161 ) Nominal Bore & Wall Thickness-32 mm NB with 3.2 mm Thickness.Foundation Pipes with anchoring-750mm deep GI Pipe, supported with M.S. Angle 25 X 25 X 4mm.Nominal Bore of Foundation Pipe-100 mm.Foundation Pipe, Class as per IS 1239-Heavy.Foundation Pipe Pipe ( as per IS 1161 ) as per clause 3, Nominal Wall & Thickness-32 mm NB with 3.2 mm Thickness.M S Foundation Plate Thickness-12 millimeter.Galvanization of all Pipes-Zinc coating on the tubes shall be in accordance with IS 4736 latest.Bearing-Tapered Roller Bearing.Nuts and Bolts for Assembly-Stainless Steel.Foot .
234	Supply and Installation of Double Surf Board -Outdoor Gym Equipment.Type-Double.Length -950 millimeter.Width-700 millimeter.Height-1300 millimeter.Maximum User Weight .-120 kilogram.Governing Specification for GI Pipes-BIS specification No IS 1161:201 4, latest.Main Central Pipe-150mm Nominal Bore G.I. Pipe.Main Central Pipe ( As per Clause 3, of IS 1161 ) Nominal Bore & Wall Thickness-150 mm NB,165.1 mm OD & 4.5 mm Thickness.Movement (Paddle) Frame-32mm Nominal Bore G.I. Pipe.Movement ( Paddle ) Frame Pipe, Class as per IS 1239 Medium.Movement ( Paddle ) Frame Pipe ( As per as per Clause 3, of IS 1161 ) , Nominal Bore & Wall Thickness-32 mm NB with 4 mm Thickness-Connecting Links-32 mm Nominal Bore G.I. Pipe.Connecting Links Pipe, Class as per IS 1239-Medium.Handle Frame-32mm Nominal bore G.I. pipe.Handle Frame Pipe ( as per IS 1161 ) as per clause 3, Nominal Wall & Thickness-25 mm NB with 2.6 mm Thickness.Foundation Pipes with anchoring-Foundation Pipes with anchoring.Nominal Bore of Foundation Pipe-100mm.Foundation Pipe Pipe ( as per IS 1161 ) as per clause 3, Nominal Wall & Thickness-100 mm NB with 4.5 mm Thickness.M S Foundation Plate Thickness-12 millimeter-Galvanization of all Pipes-Zinc coating on the tubes shall be
235	Supply and Installation Air Walker of OUT DOOR GYM EAUIPMENT Air Walker7 Stroller SingleType-Single.Length -1500 millimeter.Width-600 millimeter.Height-1400 millimeter.Maximum User Weight -120 kilogram.Governing Specification for GI Pipes-BIS specification No IS 1239 ( Part 1 )- 2004, latest.Main Frame-100mm Nominal Bore G.I. Pipe.Main Frame Pipe, Class as per IS 1239-Heavy.Designation of Main Frame Pipe ( as per IS 1161 )-GI pipeC-cIass,80mm.leg movement frame-40mm Nominal Bore G.I. Pipe.Designation of Leg movement frame Pipe ( as per IS 1161 )-GI PipeC-cIass,40mm.Handle Frame-32mm Nominal bore G.I. pipe.Handle Frame Pipe, Class as per IS 1239-Heavy.Bearings-Ball Bearing.Foot Rest-Fibre Reinforced Plastic.MS Foundation Plate Thickness-10 millimeter.Foundation Pipes with anchoring-750mm deep GI Pipe, supported with M.S. Angle 25 X 25 X 4mm.Nominal Bore of Foundation Pipe-100mm.Designation of Foundation Pipe ( as per IS 1161 )-GI pipeC-cIass,750mm.Galvanization of all Pipes-Zinc coating on the tubes shall be in accordance with IS
236	Supply and Installation of Arm WheelThree Wheel Shoulder Builder/ Arm Wheel- Outdoor Gym Equipment.Type-Three Wheel.Height of Main Central Pole from ground-1600 millimeter.Outside Diameter of first wheel-800 millimeter.Outside Diameter of second wheel-850 millimeter.Outside Diameter of third wheel-850 millimeter.Height of first wheel from ground-1300 millimeter.Height of second wheel from ground-1189 millimeter.Height of third wheel from ground-1189 millimeter.Governing Specification for GI Pipes-BIS specification No IS 1161:2014, latest.All the GI Pipes are ISI marked-Yes.Main Central Pipe construction-80mm Nominal Bore G.I. Pipe.Designation of Main Central Pipe ( as per IS 1161 )-100 mm.Ring ( Wheel )-25mm Nominal Bore G.I. Pipe.Designation of Rin.g ( Wheel ) Pipe ( as per IS 1161 )-40 mm.Pipe of Spokes of Wheel-15mm Nominal bore G.I. pipe.Designation of Pipe of Spoke of Wheel ( as per IS 1161 )-20 mm.Number of Spokes in Wheel-6.Connector Pipe ( between Main Central Pipe and Wheel )-32 mm Nominal bore G.I. pipe.Designation of connecting pipe ( as per IS 1161 )-20 mm.MS Foundation Plate Thickness-10 millimeter.Foundation Pipes with anchoring-750mm deep GI Pipe, supported with
237	Supply and Installation of Sit Up Board Double Station.Name of the productSit Up Board.Type.-Double Station.Length-1250 millimeter.Width-1050 millimeter.Height-720 millimeter.Material of Back Rest-Mild Steel Plate.Thickness of Back Rest-2 millimeter.Governing Specification for GI Pipes-BIS specification No IS 1239 ( Part 1 )- 2004, latest.Main Frame/Central Pipe-100 mm Nominal Bore G.I. Pipe.Main Frame/Central Pipe, Class as per IS 1239-Heavy.Main Frame/Central Pipe (As per Clause 3, of IS 1161) Nominal Bore & Wall Thickness-100 mm NB with 5.4 mm Thickness.Grade of Material as per table 2 of IS 1161-YSt 210.Foot Rest Pipe-40mm Nominal Bore G.I. Pipe.Foot Rest Pipe , Class as per IS 1239-Medium.Foot Rest Pipe ( As per as per Clause 3, 1161),of IS ,Nominal Bore & Wall Thickness-40 mm NB with 2.9 mm Thickness.Back Rest Frame Pipe and Connecting Links-25 mm Nominal Bore G.I. Pipe.Back Rest Frame Pipe and Connecting Links ( As per Clause 3, of IS 1161 ) Nominal Wall & Thickness-32 mm NB with 3.2 mm Thickness.Leg Support Pipe-40 mm Nominal bore G.I. pipe.Leg
238	Supply and Installation of LED SOLAR STREET LIGHT 75WP.Battery capacity-≥ 12.8 V (nominal), 30 Ah at STC (1 day autonomy).Type of LED (Light source)20 Watt White LED type.Ingress protection-IP65 or better.Nominal bore size of tube -40 mm / 3.2 mm.Height of pole (in m) - 6.Battery box-Outside the luminaire enclosure in a vented, acid proof and corrosion resistant, hot dip galvanized metallic box (IP65 or better) with anti-theft locking arrangement for outdoor use.Type of PV Module-Only indigenous modules of IEC Tested used. Crystalline high power/efficiency cells used in the solar photovoltaic module.Power output of PV Module-≥ 75 Wp at 16.4 ±0.2 Volt at STC.PV Module Efficiency-≥ 14%.The open circuit voltage of the PV modules under STC (in volts)- 21.Type of Battery-Lithium Ferro Phosphate battery (LiFePo4). Operating from dusk to dawn first four hour full brightness, rest of the time at lower level, with motion sensor.Battery capacity-≥ 12.8 V (nominal), 30 Ah at STC (1 day autonomy).Cycle/ Current-Battery cycle life 2000 cycle at 80 % discharge.Type of led-20 Watt
239	ADD GST 18%
240	ADD 1% LABOUR CESS

Need a Bussiness Loan? Apply Now!
Buy Digital Signature
Bidding Support

Also Visit

Tenders

Jharkhand Tenders

Services Tenders

Space Planning and Designing Tenders

Gardening Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Development Of Park In Kangoi Under Nagar Parishad Mihijam, Mihijam-Jharkhand

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Development Of Park In Kangoi Under Nagar Parishad Mihijam, Mihijam-Jharkhand

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us