|
| 1 | Taking down cement plaster of any description, thickness including raking out joints hacking for key scrubbing down with water, complete all as specified and directed. |
| 2 | Demolition of brick / stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding shlars facings, dressed stone work and pre-cast concrete rticles, complete all as specified and directed. |
| 3 | M&L for Brick work with sub class ‘B’ brick, straight or curved as plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified and directed. |
| 4 | M&L for 15 mm thick cement mortar 1:6 on Brickor concrete surface finished even and smooth without using extra cement, complete all as specified and directed. |
| 5 | M&L for 15 mm thick cement mortar 1:4 on fair faces of brick work using water proofing compound and finished even and smooth without using extra cement, complete all as specified and directed. Note :- Water prrofing compound shall be measured and paid seperately \"Supply only\". |
| 6 | M&L for preparation of new surface of wall and applying two coats of distemper oil emulsion over a coat of primer above 1mm thick wall care putty on new surfaces, complete all as specified and directed. |
| 7 | M&L for complete removal of existing treatment and applying two coats of distemper oil emulsion over a coat of primer above 1mm thick wall care putty on wall, complete all as specified and directed. |
| 8 | All as per Srl item No 7 above but 1st coat of 10 mm thick in cement mortar 1:6 and above 5mm thick in cement mortar 1:4as in 2nd coat of rendering with Water proofing compound. Note : Water proofing compound will be measured and paid separately as \"Supply only\". |
| 9 | M&L for prepration of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer, complete all as specified and directed. |
| 10 | M&L for complete removal of existing treatment and applying two coats of cement base paint over a coat of alkali resistant primer including wall care putty on wall, complete all as specified and directed. |
| 11 | M&L for plastering 5 mm thick in cement mortar 1:3 furnished even & smooth without using extra cement as on ceiling, complete all as specified and directed. |
| 12 | M&L for prepration of new surfaces and applying three coat of white wash on ceiling, complete all as specified and directed. |
| 13 | M&L for prepration of old surfaces and applying one coat of white wash on ceiling, complete all as specified and directed. |
| 14 | Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 15 | M&L for Glazed ceramic jointless coloured tiles 300 x 200mm x 6-7 / 450 x 350 x 7 mm thick on vertical surfaces as in skirting /dado, set and jointed with neat cement slurry and pointed in white/coloured cement to match the shade of tiles over and including 10mm thick rendering in cement mortar 1:4, complete all as specified and directed. |
| 16 | M&L for Non skid jointless cerermic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in neatcement slurry and pointed in white or coloured cement with pigment, complete all as specified and directed. |
| 17 | M&L for Non skid jointless glazed cerermic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in neatcement slurry and pointed in white or coloured cementwith pigment, complete all as specified and directed. |
| 18 | M&L for 15mm thick screed bed or bedding layer of cement mortar (1:6) as in floor for laying floor tiles, complete all as specified and directed. |
| 19 | Taking down chowkhats or frame with shutter without taking off shutter from the frame areaexceeding 1.5 Sqm but not exceeding 4 sqm each, complete all as specified and directed. |
| 20 | Taking down chowkhats or frame with shutter without taking off shutter from the frame area not exceeding 1.5 Sqm each, complete all as specified and directed. |
| 21 | S&F pressed steel frames of size 125x60mm for doors made out of PBC sheet 1.25mm thick with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed. |
| 22 | M&L PCC 1:3:6 type C-1 as in hold fast for pressed steel frames and back filling of pressed steel frame, complete all as specified and directed. |
| 23 | S&F 35 mm thick IInd class hard wood plain framed factory made paneled shutters with panel of 9 mm BWP commercial ply 12mm thick veneering on both veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS :1003 (part-I) kiln seasoned and chemically treated, complete all as specified and directed. |
| 24 | S&F 35 mm thick IInd class hard wood glazed or skelton shutter factory made open rebated prepared to receive glass, gauge etc. without sash bars edges of framing plain fitted with cut & mitred beads for securing glass etc size of member all as per clause 8.24 (a) of SSR part-I, complete all as specified and directed. |
| 25 | S&F Powder Coating aluminium frame for doors, windows, (minimum thickness of powder coating 50 micron) ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and directed. |
| 26 | S&FPowder coating aluminium window and ventilator shutters, side hung/fixed type without sash bars, aluminium section weighing 0.55 kg/ m including necessary joining cleats, zing clips, ruber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stay, Tower bolt 150mm long 1 No. hinge type B-21 100 mm long 2 Nos, suitable handle 1 No (minimum thickness of powder coating 50 micron), complete all as specified and as directed. |
| 27 | Supply and fixing anodised aluminium grill (anodised transparent or dyed to required shade according IS : 1868 / pattern, with approved standard section and fixed to the existing window frame with CP brass stainless steel screws @ 200 mm centre to centre including cutting the grill to proper opening size for fixing and operaton of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and as directed. |
| 28 | S&F 4.8 mm thick sheet glass selected quality plain/ tinted in squares not exceeding 0.5 sqm each pane, complete all as specified and as directed. |
| 29 | S&F Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and as directed. |
| 30 | M&L 9 mm thick Prelaminated particle board, interior grade, prelaminated both sides with decorative choice laminations, fixed with screws to frame work, complete all as specified and as directed. |
| 31 | S & F Solid PVC door frame of size 50mm x 47 mm made ot of 5 mm plain colour PVC sheet reinforced with MS square tube, suppling and fixing in opening as per specifiecation, complete all as specified and as directed. |
| 32 | All as per item No 31 above but single side prelam PVC Sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet and fixing in opening as per specification, complete all as specified and as directed. |
| 33 | S&F 30 mm thick factory made solid panel PVC door shutter consisting of frame made out of MS tube for top and bottom rail, MS frame shall be covered with heat moulded wood grain printed PVC sheet used with Single Side Prelam PVC sheet and stile & rails having one side feathered edge and on other side 10mm and 90 degree bent edge and fixing in the frame at site, complete all as specified and as directed.Note:- PVC door for bath /WC & Cub board. |
| 34 | Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC \"C\"channelhaving a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for TOP rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in MS Frame welded/sealed to the stiles & rails with suitable PVC shet beading and jointed together with solvent cement supply and fixing in frame at site complete all as specified and as directed. |
| 35 | S&F 100 mm size butt hinges medium weight cold rolled mild steel, complete all as specified and as directed. |
| 36 | S&F Floor doors stoppers of aluminium alloy body and tenque anodisede with hard drawn steel spring fixed in floor 150mm long, complete all as specified and as directed. |
| 37 | S&F aluminium anodised barrel tower bolts of extruded section and fixed 200 mm long, complete all as specified and as directed. |
| 38 | S&F aluminium anodised barrel tower bolts of extruded section and fixed 150 mm long, complete all as specified and as directed. |
| 39 | S&F aluminium handles cast type anodised 150mm long, complete all as specified and as directed. |
| 40 | S&F 300 mm long aluminum anodised sliding door bolts, aluminium alloy, door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium, complete all as specified and as directed. |
| 41 | S&F mild steel 300mmordinary rat tail rod door spring, patteren including roller and roller plate, complete all as specified and directed. |
| 42 | M&L for preparation of new wood surface of any description over 10 cm width or grith and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed. |
| 43 | Taking up or down 15 mm dia steel tubing and connections including cleaning for re-fixing or removal to store, complete all as specified and directed. |
| 44 | Taking up or down 20 mm dia steel tubing and connections including cleaning for re-fixing or removal to store, complete all as specified and directed. |
| 45 | S&F 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 including fittings on walls / ceiling or laying in floors, complete all as specified and directed. |
| 46 | S&F 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 including fittings on walls / ceiling or laying in floors, complete all as specified and directed. |
| 47 | S&F in repair 15mm size bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed but fancy type chromium plated, complete all as specified and directed. |
| 48 | S&F fancy type bib tap 15 mm bore cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle for iron pipe or brass ferrule, complete all as specified and as directed. |
| 49 | S&F in repair mixer cast copper alloy with capstan head, chromium plated, screwed down, high pressure with or without lettered \"Hot\" or \"Cold\" with long shank and fly nuts screwed for iron pipe or for brass ferrule 15mm bore, complete all as specified and directed. |
| 50 | S&F in repair 15mm Stop valves, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed but fancy type, chromium plated with long shank and cup (concealed type), complete all as specified and directed. |
| 51 | S&F fancy typestop valve cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle of 15mm bore, complete all as specified and directed. |
| 52 | S&F in repair viterous china ware wash down water closet pan (Pedestal Pattern) white including plastic seat and cover with MS CP hinges, complete all as specified and directed. |
| 53 | S&F viterous china ware wash down water closet pan (Pedestal Pattern) white including plastic seat and cover with MS CP hinges, complete all as specified and directed. |
| 54 | S&Fin repair Orrisa pattern WC in ground floor vitreous china white of size 580mmx440mm including provision of lime concrete bedding including breaking up of existing damaged WC seat and connecting flush pipe etc, complete all as specified and directed. |
| 55 | S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 mtr long flexible tube and ABS wall hook including making cannections and fixed in position complete in all respect, complete all as specified and directed. |
| 56 | S&FHealth faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipes with 1.25mtr long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and directed. |
| 57 | S&F in repair PVC connection 450 mm long, 15mm size with PTMT nuts, complete all as specified and directed. |
| 58 | S&F in repair 10 ltr PVC valve less symphonic action type flushing cistern, low level white with inlet ball valve float and handle with flush pipe, complete all as specified and directed. |
| 59 | S&F 10 ltr PVC valve less symphonic action type flushing cistern, low level white with inlet ball valve float and handle with flush pipe, complete all as specified and directed. |
| 60 | S&F in repair CP brass shower rose 125mm size with or without swivel joints 125mm size including fixing to steel pipe or union, complete all as specified and directed. |
| 61 | S & F vitreous china wash hand basin white flat back size 550 mm x 400mm excluding, waste chaina and plugand porcelain stopper but including brackets, cutting for and pinning in ends of brackets or erecting stand, waste coupling and waste pipe, complete all as specified and directed. |
| 62 | S&Ffancy type Pillar taps 15 mm, cast copper alloy with capstan heads, chromium plated swan neck screwed down high pressure with crutch or butterfly handle of 15mm bore, complete all as specified and directed. |
| 63 | S&F brass chromium plated tubular towel rail 20mm dia (D) type 60cm long between flanges, complete all as specified and directed. |
| 64 | M&L for preparation of new steel surface of any description over 10 cm width or grith and applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed. |
| 65 | Demolotion of stone slabs and tiles of any description or thickness laid, bedded and pointed in any mortar in floors, aprons etc, complete all as specified and directed. |
| 66 | M&L granite slab (of any type) 20mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in and including 15mm thick screed bed of cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to matchthe shade of granite, complete all as specified and directed. |
| 67 | M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situation, complete all as specified and directed. |
| 68 | M & Lfor machine cut kota stone slab 18 to 20 mm thick as in flooring / stair case landing, laid over and including 15mm thick cement screed base in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, complete all as specified and directed.Note:- Single peices stone shall be used in trads only & 3 Nos of V groove is to be made in the edge. |
| 69 | M & Lfor machine cut kota stone slab 18 to 20 mm thick as in skirting / steps / floorlaid over &including 10mm thick cement screed base in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, complete all as specified and directed.Note:- Single peices shall be used in riser only. |
| 70 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc, including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and directed. |
| 71 | S&F for 75 mm dia PVC (SWR)waste/rain water pipes single socketedin any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed. |
| 72 | S&F for 110 mm dia PVC (SWR)waste/rain water pipes single socketedin any length with rubber ring joints laid in trenches or in floors / walls etc, complete all as specified and directed. |
| 73 | S&F 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, step clamps fixed to walls, complete all as specified and directed. |
| 74 | All as per item No.73 here in before but for 110mm dia pipes. |
| 75 | S & F PVC (SWR) bends 75 mm dia, complete all as specified and directed. |
| 76 | S & F PVC (SWR) bends with provided with access 110 mm dia, complete all as specified and directed. |
| 77 | S&F PVC (SWR) junction double, (Single T), equal or unequal 110 mm dia with acess door, complete all as specified and directed. |
| 78 | S&F PVC (SWR) vent cowl 75 mm dia, complete all as specified and directed. |
| 79 | S&F 110mm PVC (SWR) reducers, complete all as specified and directed. |
| 80 | M&L 100mm dia PVC floor trap with CP grating including jointing to waste pipe with cement solvent, complete all as specified and directed. |
| 81 | Demolition of cement concrete in ground floor and paving not exc 15 cm thickness (below or above ground level), complete all as specified and directed. |
| 82 | M&L for 75 mm thick PCC 1:3:6 type C-2 as in plinth protection / floor sub base etc, complete all as specified and directed. |
| 83 | M&L 100mm thick Cement concrete type D-2, 1:4:8 (40mm graded stone aggregate), complete all as specified and directed. |
| 84 | M&L 75mm thick PCC 1:4:8 Type D-2 using 40mm crushed stone aggregate as in sub base floor, complete all as specified and directed. |
| 85 | M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in bed to drain pipe including packing to drain pipe and hunching against sides of pipe for 150mm dia pipes, complete all as specified and directed. |
| 86 | M & L for PCC 1:4:8, type D-2, using (40mm graded stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed. |
| 87 | M&L for Sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed. |
| 88 | M&L 60mm thick rubber finish interlocking paver block with grey cement and pigment of any size and shape confirming to IS 15658-2006, M-35 Grade as approved, laid in flooring and joints filled / broomed with fine sand, complete all as specified and directed. |
| 89 | Dismantling of brick tiles or terracing tiles including removal ofmud fuska from roof, complete all as specified and directed. |
| 90 | M&L PCC (1:2:4) type B-1 using 20mm graded stone gregete as in roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified and directed. |
| 91 | M&L for wire brushing with neat cement slurry with 3kg of cement per sqm at top and bottom of base coat and cleaning top, complete all as specified and directed. |
| 92 | M & L for PCC padding average50 mm thick to be provided in slope in PCC 1:2:4 type B-1, using 20mm graded stone aggregate, complete all as specified and directed. |
| 93 | M&L for plastering 10mm thick in cement mortar 1:4 mixed with WPC over cleaned concrete surfaces, complete all as specified and directed. Note :- Water proofing compound shall be measured and paid separately. |
| 94 | Supply only integral waterproofing compound, complete all as specified and directed. |
| 95 | M&L for preparation of roof top surfaces, providing and applying UV stable single component Damp Proof Ultra fibre reinforced elastomeric liquid water proofing membrane formulated with PU hybrid polymers and reinforcing acrylics fibres and having Sun Reflectivity Index (SRI) of 106 on top of conrete roof surfaces in three coat including self primar at ratio of damp proof ultraand water 3:1 and covrage @ 1 Ltr / 1 Sqm with a thickness of 650 micron, the vital physical and chemical parameters shall be as under :Min Elongation at break of 350%, Resists positive hydrostatic pressure of upto 10 bars, crack bridging ability of 2.5 mm at 650 microns. The material shall be applied with brush or roller, complete in all respect as per the direction of Engineer in Charge/manufacturer\"s instruction complete all as specified and directed. Note :(i) 6hrs interval between two coat will be maintain. (ii)The water proofing treatment shall be got carried out by the manufacturer or their authorised applicators duly approved by GE in writing.(iii) 5% amount of the total amount of water proofing treatment shall be retained as a guarantee and shall be released after 10 years . However contractor may deposit the FDR of same amount in favour of GE . If contractor fail to rectify the defect pointed out during this period in writing , the defect shall be got rectified at contractor \" risk and cost and the payment shall be made from the amount ofkept reserved or by encashing the FDR deposited by the contractor as guarantee. the contractor\"s quoted rates for this item shall deemed to be inclussive of this aspect. |
| 96 | M&L for repairing RCC projection chajjas, roof, facia etc. by necessary preparation, scraping, cutting, chiseling derustingand cleaning exposed reinforcement surfaces of damaged, loose RCC surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregates and reinforcement with welded mesh of weight exc 2Kg per Sqm but n.exc 3Kg/Sqm (if required) with or without facia and finished with cement morte 1:3 using coarse sand and work in patches area n.exc 5 Sqm and thickness RCC member not exceeding 70mm including necessary formwork and applying two coats of finishes to match with the existing surfaces at any height, complete all as specified and directed. |
| 97 | M&L for providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in apron, complete all as specified and directed. |
| 98 | M&L for providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors, complete all as specified and directed. |
| 99 | M&L for providing and injecting chemical emulsion for Post Constructional Anti-termite At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ .5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same, complete all as specified and directed. |
| 100 | S&F chain link MS galvanised fencing any size including lines wires straining bolts including binding wires etc, complete all as specified and directed.Note :-The weight of the chain link fencing after arrival at site shall be ascertained by a Board of Officers to be detailed by the Accepting Officer before incorporation in the work. |
| 101 | S&F MS angle iron as in posts and struts as in fencing including cutting tops to shape as directed, drilled holes notching for wire etcincl all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed. |
| 102 | Dismantling cast iron work of any description, complete all as specified and directed. |
| 103 | S&F rolled Mild steel work as in compound girders and stanchions, lattice girders, aerial masts, staging for water tanks (coolar stand) and like including caps bases, splices and cutting holes etc built up from two or more beam or channel sections or angles with plates or pipe section including all lattice bars, stiffeners, gusset plates etc..(Fe-410-W (Gde E-250) Quality-A), complete all as specified and directed. |
| 104 | S&F in repair750 ltr rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position of any description, complete all as specified and directed. |
| 105 | S&F 250 ltr rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position, complete all as specified and directed. |
| 106 | S & F 20mm bore ball valve high pressure PTMT with epoxy coated aluminium rod & high density polythene float balland fly nut screwed for iron pipe, complete all as specified and directed. |
| 107 | S & F in repairs harrison rails, anodised alluminium alloy with fixing brackets, stops, rollers etc, complete all as specified and directed. |
| 108 | S&F providing precast cement concrete louvers and jallies 45mm thick ( measured solid) including all mouldings but excluding frame (pre-cast frame shall be measured seperately) setting in cement mortar 1:4 precast cement concrete jalli type B-0 1:2:4 (12.5mm graded stone aggregate), complete all as specified and directed. |
| 109 | Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc and getting out in soft/loose soil, complete all as specified and directed. |
| 110 | Returning filling including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in soft or oose soil and getting out, complete all as specified and directed. |
| 111 | M&L for surface excvation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/loose soil, complete all as specified and directed. |
| 112 | Removing excavated matireal not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as specified and directed. |
| 113 | M&L for RCC M-20 design mix as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc basement slabs, under reamed piles and mass concrete, complete all as specified and directed. |
| 114 | M&L for RCC M-20 design mix as in Columns, pillars, piers, posts and struts, complete all as specified and directed. |
| 115 | M&L for RCC M-20 design mix as in Beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and directed. |
| 116 | M&L for RCC M-20 design mix as in slabs supported on walls,beams and coloumns in floors, roof, landings, balconies, canopies, deck slab and in shelves and the like, complete all as specified and directed. |
| 117 | M&L for Form work to sides of concrete foundations, footings, base of columns sides and soffits of foundation and plinth beams, complete all as specified and directed. |
| 118 | M&L for From work to sides of pillars, post, struts and columns, complete all as specified and directed. |
| 119 | M&L for Form work to sides and soffits of floor or roof beam, lintels, lintel bands etc, complete all as specified and directed. |
| 120 | M&L for Form work tosoffits of suspended slabs such as roof slabs, floor slab sand similar work etc, complete all as specified and directed. |
| 121 | S&F mild steel TMT bar 10 mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for column,hooking ends and binding with mild steel wire not less than 0.9mm dia, complete all as specified and directed. |
| 122 | S&F mild steel TMT bar 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders & cut to length bent to shape required including cranking, bending spirally for hooping for column, hooking ends and binding with mild steel wire not less than 0.9mm dia, complete all as specified and directed. |
| 123 | S&F 600 mm x 450 mm beveled edge mirror of selected quality glass,mounted on 6 mm thick AC building board or commercial ply wood and fixed to wooden plugs with chromium plated brass screwes and cup washers, complete all as specified and directed. |
| 124 | S&F swivel shower, PTMT any colour for fixing with 15mm pipe (minimum weight 40 gms) including shower arm 15 mm size, 195 mm long with bend of 45 degree with flange of PTMT any colour (Minimum weight 40 gms), complete all as specified and directed. |
| 125 | M&L for hardcore of broken stone boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface, complete all as specified and directed. |
| 126 | M&L for Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors withgrey cementandpigment over and including20mm thick screed bed or bedding layerin cementmortar 1:4,complete all as specified and directed. |
| 127 | S&F MS work as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, conforming to Fe-290 (Gde E-165), complete all as specified and as directed |
| 128 | S&F anodised aluminium snap grid frame work for false ceiling, size of grid 605 x 605mm including hangers 6mm dia GI (Upto 1200mm length), adjusting level fixed to roof slabs with ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasteners, 12.5 mm dia, 40 mm long including 12mm thick, 60cm x 60cm size gypsum board as in ceiling flat or sloping fixed with screws as per manufacturers instructions, complete all as specified and as directed. |
| 129 | M&L for RCC pipes class NP2 of 150mm dia laid and jointed with collars, complete all as specified and directed. |
| 130 | M&L for cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benchingfor and forming branch channel (1/2 or 3/4 section) in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate finished smooth and reforming benching as required for 150mm dia pipe, complete all as specified and directed. |
| 131 | S&F Stainless Steeltubes of any size for grab railing/any work including bolting, anchoring, welding, any type offixing material etc, complete all as specified and directed. |
| 132 | Taking out of old unserviceable GI steel tubing and its connetion fitting, complete pipe line work of size 40/50 mm bore, complete all as specified and directed. |
| 133 | Taking out of old unserviceable gate / globe valve complete accessories from existing pipe line of size 25 mm bore, complete all as specified and directed. |
| 134 | Supply and laying galvanised iron pipe of size 25 mm dia bore, medium grade including all necessary fittings and dully laying through in trenches / on wall/under hard standing path / road etc, complete all as specified and directed. |
| 135 | Supply and laying galvanised iron pipe of size 20 mm dia bore, medium grade including all necessary fittings and dully laying through in trenches / on wall/under hard standing path / road etc, complete all as specified and directed. |
| 136 | S&F brass gun metal gate valve of size 25 mm dia bore with having iron wheel head screwed both ends, complete all as specified and directed. |
| 137 | S&F brass gun metal gate valve of size 20 mm dia bore with having iron wheel head screwed both ends, complete all as specified and directed. |
| 138 | Taking Out old unserviceable LT UG cables of sizes having cross sectional area 16-35 sqmm, 4 /3.5 /2 core, complete all as specified and directed. |
| 139 | Supply and laying cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sqmm 4 core including fixing materials like lugs, cable glands etc. laid in trenches, floor, fixed to wall etc, complete all as specified and directed. |
| 140 | Material and labour for sand cushioning with a layer of sand 80 mm thick before laying of cable and 15 cm thick (punned down to 100 mm thick) after laying of cable in trenches / ducts, complete all as specified and directed.Note: Punned down thickness (overall 18 cm) shall be measured and paid. |
| 141 | Supply and fixing, factory made unreinforced precast concrete cable cover LV type-1, flat, of size 300x180x40mm, laid flat and dryin trenches over the cable for protection, length perpendicular to the direction of cable adjacent to each other, complete all as specified and directed. |
| 142 | Material & Labour for galvanised iron tubes 40 mm bore, light grade for protection of cable with & including all fittings fixed to wall, pole or laid in road / floors etc, complete all as specified and directed. |
| 143 | Taking down copper/aluminium point wiring for (light, fan , socket or power and bell) complete including unserviceable fittings such as switches, ceiling rose, holders, sockets bell etc. and making good the distrubed surfaces on wall/floor etc, complete all as specified and dirceted. |
| 144 | Taking down MCB DB TPN/SPN/ and load of any make and type inclduing dismantling all electrical connections from MCBs/MCCB/isolators and making good the distrubed surface, complete all as specified and dirceted. |
| 145 | Disconnecting and taking down old existing light fitting of any description from any position, complete all as specified and dirceted. |
| 146 | Disconnecting, taking up the existingelectric fan and deposited to mes store yard with all accessories, complete all as specified and dirceted. |
| 147 | Disconnecting and taking down old existing sub main wiring of any description from any position, complete all as specified and dirceted. |
| 148 | Disconnecting and taking down old existing Earthing any size and shape, complete all as specified and dirceted. |
| 149 | M&L for Point wiring using proper colour coding complete with 1100 Volts grade 1.5 Sqmm, single core, PVC insulated, unsheathed cable with multistranded copper conductor with FRLS grade, confirming to IS-694 in and including PVC medium grade conduit not less than 25mm dia. with all accessories concealed in wall / ceiling / floor /roof etc,including GI terminal boxes with 3 mm thick plastic laminated sheet cover having necessary cutting for fixing switches/ socketsincluding 1.5 Sq.mm PVC insulated, unsheathed, multistranded copper conductor, FRLS 1100 volts grade (green colour) as earth wire, connected to common earth dolly for:- |
| 150 | One light point/ fan/Exhaust controlled by one switch. |
| 151 | One three pin switch socket 5 amps outlet on same board. |
| 152 | One three pin switch socket 5 amps outlet on Independent board. |
| 153 | All as per item No 149 here-in-before but with 2.5, Sqmm cable. |
| 154 | S & FSwitch piano, flush type single pole, one way 5 Amp, complete all as specified and directed. |
| 155 | S & F Socket outlet 3 pin, 5A, flush type, complete all as specified and directed. |
| 156 | S & FSwitch piano, flush type single pole, one way 15 Amp, complete all as specified and directed. |
| 157 | S & F Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type, complete all as specified and directed. |
| 158 | S&F ceiling rose surface bakelite 65x50mm with three terminals, complete all as specified and directed. |
| 159 | S&F Fan stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc as required, complete all as specified and directed. |
| 160 | S&F Sheet metal enclosure DB TPN, 4 way with 200 Amp rated bus bar, 415 V, double door . for fixing MCB’s, isolators etc., having IP-43 protection,flush mounting, complete all as specified and directed. |
| 161 | S&F Sheet metal enclosureDB SPN, 8 way with 200 Amp rated bus bar, 240 V, double door . for fixing MCB’s, isolators etc., having IP-43 protection,flush mounting, complete all as specified and directed. |
| 162 | Supply and fixing 415V 10KA \"B\" curve miniature circuit breaker (MCB)TPN 40 Amps to 63 Amps and current carrying capacity in the DB complete with connection testing and commissioning, complete all as specified and directed. |
| 163 | S&F 10KA \"C\" curve miniature circuit breaker (MCB) SPN6 to 32 Amp rating 240V in the MCB DB complete with connection testing and commissioning, complete all as specified and directed. |
| 164 | Supply and fixing MCB,SP, 6 Amp to 32 Amp, 240 Volt, 50HZ, 10 KA, `C` Series, making electrical connection with the help of Lugs/thimbles, complete all as specified and directed. |
| 165 | Supply and fixing LED lights fitting 4 ft long 1x 20W, 220V AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed. |
| 166 | S&F submain wiring with 2X 4 sqmm (nominal area) PVC insulated FRLSH, unsheathed, multistrand, 1100 volts grade copper conductor cable single core, drawn through in and including non metalic PVC concealed conduit not less than 20mm dia, medium grade with accessories including one run of 4 sqmm PVC insulated copper conductor cable FRLS unsheathed multistranded, complete all as specified and directed.Note:- surface conduit shall be laid in celing portion only. |
| 167 | S&F building security light 35 Watt including fittings connection from ceiling rose to light fitting with twin core cable 23/0.0076 sqmm, complete all as specified and directed. |
| 168 | Supply and fixing exhaust fan, steel body, heavy duty AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers, complete all as specified and directed. |
| 169 | S&F ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor, complete all as specified and directed. |
| 170 | S&F electric water heater, storage type steel body with SS inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece etc, complete all as specified and directed. |
| 171 | Supply, installation, commissioning of Water cooler fully stainless steel, electric driven single phase having approx storage 40 ltsand nominal coolingcapacity 80 ltrs, complete all as specified and directed. |
| 172 | M&L for Earthing with galvanised steel earth plate electrode of size 60cmX60cmX6cm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5m bellow normal ground level, connected to the galvanised earth lead by means of bolts, nuts and washers of galvanised iron or steel using GI or steel wire 4.00 mm diaas earthing lead as shown in electrical plate No 3 of SSR Part-I connected to earthing test point all as specified or indicated including testing on complete including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC 1:2:4 type B-1 using 20mm grade stone aggregate pit, funnel, 20mm dia GI medium grade watering pipe, 15mm dia GI light grade earth lead protection pipe and pre-cast earth pit cover made of RCC (1:1.5:3) type A1 duly reinforced with 8mm dia TMT bar @ 150 c/c both ways, one lifting handle made of 10mm dia TMT bar embedded in cover slab and cover, wire, copper lugs etc, mesh, charcoal and common salt inalternate layer of 15cm thick, complete all as specified and as directed. |
| 173 | Supply & fixing 3 watt antique brass LED bedside wall fitted LED Study lamp 28 Cm goose neck with white light, complete all as specified and as directed. |
| 174 | S&F wall mounted fan high speed 300 mm size, 100 % copper motor winding, 3 speed control, complete all as specified and directed. |
| 175 | Supply and laying cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sqmm 2 core including fixing materials like lugs, cable glands etc. laid in trenches, floor, fixed to wall etc, complete all as specified and directed. |
