|
| 1 | Removal of spoil: Labour only for removal of spoil mixed with excavated earth, broken bricks, concrete rubbish and debris, broken glasses, cut pieces of tarfeltetc, from work site to a distance of 1.50 km. outside the factory or as directed by the EIC/SIC (20% deduction in measurement will be made from the volume of spoil ). |
| 2 | P.C.C (1:2:4) : M & L for providing plain cement concrete type-b1 ( using 20mmgraded stone aggregate) 1:2:4 mix as in foundation, floor, filling and mass-concrete etc. as ordered by EIC/SIC. |
| 3 | R.C.C (1:1.5:3).: M & L for providing reinforced cement concrete type M-20, 1:1.5:3 mix (using 20 mm graded stone aggregate) as in mass concrete, foundation, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, precast slabs etc.as ordered by EIC/SIC. |
| 4 | Brick work(1:6): M & L for brick work with old size subclass\"B\" bricks, straight or curved on plan exc 6m mean radius with (1: 6) cement morter as ordered by EIC/SIC. |
| 5 | Half Brick work: M & L for half brick thickbrick work with old size subclass ‘B’ bricks,, straight or curved on plan with (1: 6) cement mortar as ordered by EIC/SIC. |
| 6 | Cutting holes:Labour only for Cutting holes not exc. 150 sq.cm into or through brick walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as require and ordered by EIC/SIC. |
| 7 | Form work : M & L for Use & waste of wooden formwork to sides of mass concrete, foundations, footings, bases of columns, raft and raft beams, concrete road, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete as ordered by EIC & SIC. |
| 8 | Taking down frames with shutters : Labour only taking down door / window frames with shutters (without taking off shutters from the frame) exc 1.5 sqm and not exc. 4.00 sqm each and removing the same to store as ordered by EIC/SIC. |
| 9 | M.S small articles : S & F for providing mild steel straps, clamps,nut bolts, wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articlesetc, as small articles, to be fixed in position as required as ordered by EIC/SIC. |
| 10 | Reinforcement : M & L for providing reinforcementwork with TMTmild steel bars 08 mm and over, cut to length, bent to shape required, including cranking, bending, hooking ends & binding with mild steel wire (annealed) not less than 0.9 mm dia. etc.complete as ordered by EIC/SIC. |
| 11 | Steel plates : S & F mild steel plates (plain or chequered) channels, square cut or notched ordinary and counter sunk with riveted, bolted or welded attachment all as ordered by EIC/SIC. |
| 12 | M.S. framed work: S & F for framed work of trussed, purlins, joists, rails and fastenings and heavy bracket framing, steel gate, steel door (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. or others made of mild steel of approved sections including cutting, drilling, welding etc. at any position as required complete in all respect as ordered by EIC/SIC. |
| 13 | Translucent sheeting : M & Lfor roof / north light covering with 2 mm thickfiber glass reinforced translucent sheeting fixed withself tapping screws or as specified any height as north light portion oras ordered by EIC/SIC. |
| 14 | M. S. sheet : M & L for 2.5mm thick plain mild steel sheeting valley gutter / gate / door with welded joints including nozzle piece and fixed in position properly all as specified as ordered by EIC/SIC. |
| 15 | Pre-colour coated steel sheet: S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick (total coated thickness)of make: TATA Blue scope / Everest / Jindal or substantially equivalent of any colour having tensile (yield) strength of 550 mpa minimum, coated with aluminium zinc (az 150) @ 150 gm/sqm of coating (total both surfaces) as in roof covering / clading to wall, ridges etc. fixed with self tapping screws in every trapezoidal profile or as specified & as directed by the EIC/SIC. (test certificate of the material should be submitted by the firm before starting the work at site). |
| 16 | Pre-colour coated plain steel sheet: S & F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick (total coated thickness) of make: TATA Blue scope / Everest / Jindal or substantially equivalent make of any colour having tensile (yield) strength of 550 mpa minimum, coated with aluminium zinc (az 150) @ 150 gm/sqm of coating (total both surfaces) as in roofclading to wall, ridges etc. fixed with self tapping screws as specified & as directed by the EIC/SIC. (Test certificate of the materials should be submitted by the firm before any payment). |
| 17 | Taking down and refixing of roof sheeting:Labour only for taking down and refixing forroof covering with corrugated or semi-corrugated sheets in roofs, fixed with \"J\" or \"L\" hook or coach screws as required for site condition and as ordered by EIC/SIC. |
| 18 | Ceiling board: S & F of12 mm thick Gypsum Board in ceiling fixed with screw or just keep in position or otherwise as per manufacturers instructions to metal frame work, complete as ordered by EIC/SIC. |
| 19 | Neat cement finish : M & L for applying cement slurry on plastered or concrete surface to have the surfaces even & smooth as ordered by EIC/SIC. |
| 20 | Non skid flooring : S & F Non - skid Ceramiccoloured ceramic tiles (Make: Johnson / Kajaria / Orient bell or substantialy equivalent) of7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as ordered by EIC/SIC. |
| 21 | Plastering (1:6): M & L for providing 12 mm thick cement plaster 1:6 mixon fair faces of brick work or concrete surfaces at any height as ordered by EIC/SIC. |
| 22 | Topping layer(1:6): M & L for providing 5 mm thick cement layer 1:6 mixon green concrete surfaces at any height as ordered by EIC/SIC. |
| 23 | Screed bed of 15 mm: M & L for providing bedding screed bed of 15 mm thick in cement mortar ( 1:6) etc. after taking out existing PVC / tarfelt or other floor finish material (if any), complete in all respect as ordered by EIC/SIC. |
| 24 | Washable distempering: M & L for applying two coat of washable distemper of 1st quality; make- Asian / Berger / ICI or substantially equivalent make and approvedshade after necessary preparatory work to distempering including necessary priming in wall and ceiling surfaces as ordered by EIC/SIC. |
| 25 | Sheet glass : M & L for providing sheet glass 3 mm thickness, of any size and shape, any height glazed with oil puttyof approved makeall complete and all as ordered by EIC/SIC. |
| 26 | Securing of glazing: M & L for securing glass of any description in existing wooden/steelframes glazed with putty/ beads including removing loose or decayed putty/ beads, paining / oiling one coat on rebates, grooves, reputtying and painting/oiling puttied surface to match existing work all complete and all as ordered by EIC/SIC. |
| 27 | Wood painting : M & L for applying single coat of synthetic enamel paint finished glossy of 1st quality; make: Asian / Berger / ICI or substantially equivalent make, and shade over old surfaces after necessary preparationwood surfaces of any description over 10 cm width or girth as ordered by EIC/SIC. |
| 28 | Steel painting two coat: M & L for applying two coats of synthetic enamel paint finished glossy of 1st quality; Make: Asian / Berger / ICI or substantially equivalent make, and approvedshade over a coat of priming with red lead primerafter necessary preparation of new decorated steel surfaces of any description over 10 cm width or girth as ordered by EIC/SIC. |
| 29 | Preparation of old surface with primer : M & L fornecessary preparation of old decorated steel surfaces with primer for making it suitable for painting work,as ordered by EIC/SIC. |
| 30 | Preparation of new surface with primer : M & L fornecessary preparation of new decorated surfaces with primer for making it suitable for painting work,as ordered by EIC/SIC. |
| 31 | Heat resistance Painting : Labour only forapplying two coats of heat resisting paint at any height and at any position,as ordered by EIC/SIC. |
| 32 | Heat resistance Paint : Supplying for painting of heat resisting paint ofmake: Asian / Berger / Shalimar or substantialaly equivalent make and shade as ordered by EIC/SIC. |
| 33 | Taking up & down GI pipe :Labour only for taking up or down steel tubing and connections of 15mm dia.including cleaning for re-fixing or removal to store ordered by EIC/SIC. |
| 34 | Taking up & down GI pipe :Labour only for taking up or down steel tubing and connections of 25-32mm dia.including cleaning for re-fixing or removal to store ordered by EIC/SIC. |
| 35 | Refixing old steel tubing: Labour only for refixing 25-32mm dia. old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) as ordered by EIC/SIC. |
| 36 | GI pipe 40 mm dia :S & F of 40 mm bore dia Tubes ( Make: TATA / JINDAL/ BHUSAN or substantially equvalant), \"Medium grad\", galvanised, with all fitting; laid in trenche laid or fixed in proper positionincluding short lengths, with all pipe fittings such as union, ends, elbows, tees, reducingtees, adoptors, sockets, plugs, hose clips etc. and fixing to floor / walls / trenches etc, complete with saddles (snap clips), wall clips, hooks, protective mild steel tube sleeves and cutting through walls,floors and their making good or laying in trenches and also cutting, screwing and waste complete as ordered by EIC/SIC. |
| 37 | GI pipe 25 mm dia :S & F of 25 mm bore dia Tubes ( Make: TATA / JINDAL/ BHUSAN or substantially equvalant), \"Medium grad\", galvanised, with all fitting; laid in trenche laid or fixed in proper positionincluding short lengths, with all pipe fittings such as union, ends, elbows, tees, reducingtees, adoptors, sockets, plugs, hose clips etc. and fixing to floor/ walls / trenches etc, complete with saddles (snap clips), wall clips, hooks, protective mild steel tube sleeves and cutting through walls,floors and their making good or laying in trenches and also cutting, screwing and waste complete as ordered by EIC/SIC. |
| 38 | GI pipe 15 mm dia :S & F of 16 mm bore dia Tubes, \"Medium grad\", galvanised ( Make: TATA / JINDAL/ BHUSAN or substantially equvalant), with all fitting; laid in trenche laid or fixed in proper positionincluding short lengths, with all pipe fittings such as union, ends, elbows, tees, reducingtees, adoptors, sockets, plugs, hose clips etc. and fixing to floor / walls / trenches etc, complete with saddles (snap clips), wall clips, hooks, protective mild steel tube sleeves and cutting through walls,floors and their making good or laying in trenches and also cutting, screwing and waste complete as ordered by EIC/SIC. |
| 39 | Stop valves 40 mm dia: S & F of 40 mm dia Stop valves ( Make: NETA / ZOLOTO / ALTO or substantially equvalant) , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixedin proper position complet as ordered by EIC/SIC. |
| 40 | Stop valves 25 mm dia: S & F of 25 mm dia Stop valves ( Make: NETA / ZOLOTO / ALTO or substantially equvalant), cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixedin proper position complet as ordered by EIC/SIC. |
| 41 | Stop valves 15 mm dia: S & F of 15 mm dia Stop valves ( Make: NETA / ZOLOTO / ALTO or substantially equvalant), cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixedin proper position complet as ordered by EIC/SIC. |
| 42 | Bib taps: S & F of Bib taps of (Make: Alto/ Zolota / Neta or substantially equvalant) castcopper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed bib taps size of tap 15 mm bore dia. as ordered by EIC/SIC. |
| 43 | Demolition of PCC: Labour only for demolition of cement concrete of any description and in any position and removing the same out off the work site as orderd. |
| 44 | Dismantling of brick work: dismantling brick work or stone/boulder masonry of any typebuilt in cement morter including all quoins, arches, pillars etc as order by EIC/SIC. |
| 45 | Dismantling steel work : Labour only for dismantling wrought iron or mild steel work of any description and in any position and removing the same to store or as directed by the EIC/SIC. |
| 46 | Dismantling sheet : Labour only for dismantling plain or corrugated steel sheeting / galvalume sheeting of any gauge, thickness,any heightincluding Nainital or similar pattern roof coverings in roof covering and including removing the same to store or as directed by EIC/SIC. |
| 47 | Taking out & refixing of RCC slabs: Labour only for taking out of existing RCC slabs from its original position and reposition the samein its original or other position after repairing of the drain /trench(repairing of drain / trench to be paid by separate items) all complete as ordered by SIC/EIC. |
| 48 | Taking out & refixingMS cover plate: Labour only for taking out of existing plain / deformed MS drain / cable trench cover and then repositioning the same in its original or other position after straightening the plates, complete all as ordered by SIC/EIC. |
