|
| 1 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each and removing to store complete all as specified and as directed. |
| 2 | Taking down chowkats or frames with shutters (without taking off shutters from the frames)exc. 1.5 sqm but n.exc 4 sqm each and removing to store complete all as specified and as directed. |
| 3 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed. |
| 4 | Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings/wall cladding complete all as specified and as directed. |
| 5 | Dismantling wrought iron or mild steel work of any description not otherwise provided for etc.complete all as specified and as directed. |
| 6 | Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed. |
| 7 | Pre-Painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 8 | Rolled mild steel Fe-410w (Gde-E-250) quality \"B\" Roof trusses (framed ) , trussed, purlins, crane gantries , rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces cleats etc complete all as specified and as directed. |
| 9 | 10-12 mm thick gypsum boards seemess false ceiling including sunk or raised moulding or cop design as approved, moisture resistant, including GI hanging wires & frames with intermediate, perimeter channel ceiling channel, along nuts and bolts connecting plates gypsum boards, dry wall screws soffits cleats, ceiling section, rawel plugs fixtures and screws and applying two coats of emulsion paint over a coat primer on exposed surface complete all as specified and directed by Engr-in-Charge.Note : (a) Design of ceiling board as approved by Engr-in-Charge. (b) GI grid/hanging system shall be of the same make as of false ceiling manufacturer. |
| 10 | Machine cut Kota stone slab flooring 18-20mm thick over cement screed base 15 mm thick in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishingcomplete all as specified and as directed. |
| 11 | Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed 10mm thick in CM 1:4, and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishingcomplete all as specified and as directed. |
| 12 | Cabinet/cupboard in required size at site made out 18 mm thick one side decorative lamination sheet consisting of carcass 18 mm thick PVC sheet & provn of shutters made out of 18mm thick one side decoartive laminated PVC sheet all required brackets 5.5 screws etc. the panels shall be fabricated using adhesive and screws where ever required. All the edbes shall be covered with 2 mm thick edge bonding tape or 90 degree edge bent finish, necessary drawer, openable shelve with frame work complete as per make and specification mention as per drawingwith locking arragement approved by Engr-In-Charge.Colour as approved by GE, complete all as specified and as directed. |
| 13 | PVC steel catcherof superior quality complete all as specified and as directed. |
| 14 | 100 mm long stainless steel alloy handles, decorative type,complete all as specified and as directed. |
| 15 | Continuous (piano) hinges, mild steel, bright finish or elecrogalvanised width of flaps when open in 30mm and fixed complete all as specified and directed |
| 16 | Solid PVC wall lining consisting of 5mm thick wood grainprinted PVC sheet inclusive of solvent cement and fixing at site on PVC frame, complete all as specified and directed. |
| 17 | Brick work with sub class \"B\" bricks straight or curved on plan exc 6m mean radius built in CM 1:6. complete all as specified and as directed. |
| 18 | Rendering 15mm thick in CM 1:6 on fair faces of brick/concrete finished fair and even without using extra cement complete all as specified and as directed. |
| 19 | Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished fair and even without using extra cement complete all as specified and as directed. |
| 20 | Preparation of new steel surfaces of any description not otherwise discribed over 10 cm width or girth and applying two coats of synthetic enamal paint over a coat of red oxide on steel surfaces, complete all as specified and as directed. |
| 21 | Providing 50 mm thick cement concrete ( 1:4:8) type D2 using 20 mm graded aggregate as in sub base for hard paved area complete all as specified and as directed. |
| 22 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed. |
| 23 | Dura stone heavy duty vitrified tiles of size 400mm x 400mm or 300x300mmof 10mm thick as in floors set and jointed in neat cement slurry and pointed in white cement to match the surface including 15mm thick screed bed in CM 1:6 complete all as specified and as directed. |
| 24 | Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish of the premises complete all as specified and as directed. |
| 25 | Double charge glossy finished vitrified ceramic tiles 600mm x 600mm, area of each tile n exc 0. 36 Sqm, 10mm thick (square or rectangular) of superior quality as in floor and walls surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the light shade of tiles including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed. |
| 26 | Double charge glossy finished vitrified ceramic tiles area of each tile n exc 0. 36 Sqm, 10mm thick (square or rectangular) of superior quality as in floor and walls surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the light shade of tiles including 10mm thick screed bed in cement mortar 1:4 complete all as specified and directed. |
| 27 | Coloured ceramic tiles of size 600 mm x 300 mm x 7 mm thick coloured tiles on vertical surfaces set and jointed in neat cement slurry and pointed in white cement mixed with colour pigments to match the existing surface including 10mm thick backing coat in cement mortar 1:4 complete all as specified and directed. |
| 28 | 125x60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and as directed. |
| 29 | 35mm thick, flush shutters, solid core construction, with blockboard core and plywood face panels, commercial type on both sides complete all as specified and as directed by the Engineer-in-Charge/GE. |
| 30 | 30mm thick IInd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a); fitted to chowkats complete all as specified and as directed. |
| 31 | Butt hinge ISI Marked 100mm size, medium weight, cold rolled mild steel complete all as specified and as directed. |
| 32 | ISI marked 250mm long aluminium alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloys to door shutter complete all as specified and as directed. |
| 33 | 150mm long aluminium, anodized, barrel tower bolts of extruded section complete all as specified and as directed. |
| 34 | 150mm aluminium handles, cast type, anodised complete all as specified and as directed. |
| 35 | Factory made uPVC white/coloured Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where everrequired) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in Charge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 36 | Providing and fixing factory made uPVC white colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm),T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated), But Hinges of\"zinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 37 | Factory made uPVC white/coloured three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made |
| 38 | 6.3mm glass including etching as approved by Engr in Charge as in windows, partitions, doors and similar work including cutting to shape, drilling holes required complete all as specified and as directed. |
| 39 | Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified. |
| 40 | 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window sills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab complete all as specified and as directed. |
| 41 | Venetian blinds of approved make, vertical/horiozonatal type using 100mm wide fabric blinds of approved colour/ shade and pattern including operating arrangement such as chord/ thread, counter weight, connecting chain etc., and necessary fittings complete all as specified and directed. |
| 42 | Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key scrubbing down with water etc. complete all as specified and as directed. |
| 43 | Wall cladding tiles exterior store series of size 600 mm x 300 mm x 8-10mm thick on vertical surfaces set and jointed in neat cement slurry and pointed in white cement mixed with colour pigments to match the existing surface including 10mm thick backing coat in cement mortar 1:4 complete all as specified and directed. |
| 44 | Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways;railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified and as directed. |
| 45 | 4 mm dia galvanised steel wire 50 mm x 50 mm mesh made up in to matresses or cages etc complete all as specified and as directed. |
| 46 | Roughening surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3 kg/Sqm including 15mm thick screeding in CM (1:4) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separately). Applying bituminous primer on roof surfaces @ 0.40 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and provide modified polymeric APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polyethylene film. Min wt of membrane will be 3.50 Kg/Sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitument 85/25 @ 1.2 Kg/Sqm blinded with fine sand in dry condition @ 0.5 Kg/Sqm, complete all as specified and as directed. |
| 47 | 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and as directed. |
| 48 | S & F in repair 15mm bore bib tap of cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed. |
| 49 | S & F in repair 15mm bore stop valve/angle cock, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed. |
| 50 | S&F in repairs Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed. |
| 51 | S&F in repair soap dish holder incl all fittings complete all as specified and as directed. |
| 52 | S&F in repair vitreous chinawarewash hand basin (WHB) whitesize 550mm x 400mm complete including provision of pair of mild steel angle iron brackets of suitable size duly painted, 32 mm dia chromium plated waste coupling, PVC waste pipe and cutting for pinning in ends of brackets in wall etc complete all as specified and as directed. |
| 53 | Sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed. |
| 54 | S & F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed. |
| 55 | S & Fin repair Vitreous china squatting pan \"Orissa\" pattern size 580x440 mm white with integral foot rest including connection to trap and flushing pipe complete all as specified and as directed. |
| 56 | S&F in repairs 10 litres capacity PVC low level flushing cistern white inlet float valve, handle complete including brackets complete all as specified and as directed. |
| 57 | PVC connection 15 mm dia and 600mm long with two Nosof brass check nuts and washers complete all as specified and as directed. |
| 58 | 15mm steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls including taking down old pipe complete all as specified and as directed. |
| 59 | 20mm steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls including taking down old pipe complete all as specified and as directed. |
| 60 | 1000 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I and PTMT ball valve 20mm dia including taking down of old tankand removing from sitecomplete all as specified and as directed. |
| 61 | S & F in repair of gun metal gate valve, painted finish, with forged brass spindle and iron wheel head, screwed both endsfor iron pipe of size 20mm bore complete all as specified and as directed. |
| 62 | Precast reinforced cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate ) for drain cover, manhole cover septic tank covers slabs etc including necessary form work and set in CM (1:4) complete all as specified and as directed. |
| 63 | Mild steel TMT bars 10 mm dia and over cut to lenth, bent to shape required, including cranking,bending, spirally for hooping for columns, hooking ends and binding waith and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed. |
| 64 | PCC 1:2:4type B0 (12.5mm graded aggregate) as incoping, benching and similar work etc including necessary form work complete all as spcified and directed. |
| 65 | 110 mm PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall complete all as specified and as directed. |
| 66 | 110 mm PVC (SWR) bends any redius with access door complete all as specified and as directed. |
| 67 | 110 mm PVC (SWR) branch piece, (singal T) equal or unequal with access door complete all as specified and ;as directed |
| 68 | PVC (SWR) Floortrap, 75 mm dia of outlet, plain with grating including jointing with solvent cement and making good complete all as specified and as directed. |
| 69 | 600 mm long tubular tower rail brass chromium plated 20mm dia, D type 60cm long fixed with two plugs (Gutties) of 2nd class hard wood embeded in cement mortor 1:3 with MS screws complete all as specified and as directed. |
| 70 | 1mm thick wall care putty on plastered surface complete all as specified and as directed. |
| 71 | Applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed. |
| 72 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification, two or more coats on new work complete all as specified and as directed. |
| 73 | File Compactor of mechanical Mobile Storage System of 4 bays (1 bay deep) with 2082 mm height, 900 width & 457 depth of following Configuration and Specification Consisting of RAW MATERIALS as appended below :- (a) STEEL :- The System Should be made from high quality steel of furniture grade as per IS513 and IS10748 TATA Steel iumand A strum product only are used to manufacture compactors.(b)POWDER COATING :- Powder should be use donly From Reputed Manu facture like NEROLAC & ASIAN etc.(c) COLOUR :- The compactor system should be powder coated in Metallic Silver & Metallic Black finish in Pure Polyester.(d) BEARING :- Bearing from reputed manufactures is only used with corresponding test certificate Should only be used.(e)CHAIN :- Diamond or Roll-on Brand chain to be used only.(f) WHEEL:- Iron Die Cast with anti-rust Zinc. Loading:1000kg / wheel.(g)GUIDERAIL :- Made of 25mm Solid Steel with electroplate finish |
| 74 | Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 75 | Factory made uPVC white colour Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. comprising of uPVC multichambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 76 | Sheet glass 5.5mm thick of one side view or etching on glass as approved by Engr in Charge, ordinary quality and glazing with beads fixed with metal panel pins, EPDM washers or connected accessoriesin each pane complete all as specified and as directed |
| 77 | 12mm Toughned glass(etching desgin on glass as approved by Engr in Charge) as in hinged doors, partitions, automatic doors and similar work including cutting to shape, drilling holes required including all accessories like SS handle, floor machine and all connected accessoried etc complete all as specified and as directed. |
| 78 | Solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site including all fixing accessories like PVC frames/fillets etc on PVC frame, complete all as specified and directed. |
| 79 | Preparation of wall/ceiling surfaces and applying one coat of 1mm thick wall care putty complete all as specified and directed. |
| 80 | New plaster surface of walls surface and applying two coat of plastic emulsion paint (Shade approved by GE) over a coat of primer complete all as specified and directed. |
| 81 | Wall mounted cabinet of 3\" Height , 3\" width & 19\" depthfixed to wall with fasterner complete all as specified as directed by Engr in Charge of following description :-(a) STEEL :- The System Should be made from high quality steelof furniture grade as per IS513 and IS10748 TATASteel iumand Astrum product only are used to manufacture compactors.(b)POWDER COATING :- Powder should be use donly FromReputed Manu facture like NEROLAC & ASIAN etc.(c)COLOUR :- The compactor system should be powder coated in Metallic Silver & Metallic Black finish in Pure Polyester.(d) Best quality of Locking arrangement(e) Fasterner for fixing to wall as per site requirement. |
| 82 | Preparation of new plaster surfaces of walls/ceiling and applying two coats of oil emulsion distemper (white/tinted) complete all as specified and as directed. |
| 83 | Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power/ LED Light fittings) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling complete all as specified and as directed. |
| 84 | Taking down carefully copper/aluminium sub main wiring of size 2.5/4/6 sqmm from surface/concealed at any height and removing the materials from site and making good thedisturbed surfaces of walls,floors roofs etc complete all as specified and directed. |
| 85 | Taking down Old/ Unserviceable MCBDBs TPN / Main Switchesby disconnection of electric connection including old unsvMCCBs,MCBs, isolators etc and making good to distrubed surface complete all as specifiedand directed. |
| 86 | Disconnecting and taking down un serviceable light fittings of any description/ capacity complete all as specified and as directed. |
| 87 | Point wiring for one light/ fan/bell point controlled by oneswitch using 1.5 Sq mm FRLS copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit as per site requirement (thickness not less than 1.5mm and 20mm dia), medium grade with Modular sunken boxes & PVC back plate for mounting modular type switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5 Sq mm as earth wire stranded and conected to earth dolly as specified.Note:- Cutting and making samethe wall patchs after layingthe wire and conduit using putty, white wash and distamper. The surface should be made smooth using putty and should match exactly with the existing wall finish. Make:Havells/polycab/Finolex |
| 88 | All as per srl item No 87 but for 3 pin 6 Amps socket outlet independent boardincluding PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly, complete all as specified and as directed. |
| 89 | All as per srl item No 87 but for 3 pin 6 Amps socket outlet on the same board including PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly, complete all as specified and as directed. |
| 90 | All as per Srl item No 87 but for 3 Pin 16 Amps socket outlet independent board with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire standard and connected to earth dolly, complete all as specified and as directed. |
| 91 | Modular switch6 Amps single pole one way230 V, 50 Hz, AC , with inner/outer plate complete all as specified and directed by Engr In charger/GE. |
| 92 | Modular switch 16 Amps single pole one way 230 V, 50 Hz, AC , with inner/outer plate complete all as specified and directed by Engr In charge/GE. |
| 93 | Modular socket 3 Pin 6 Amps flush type 230 V, 50 Hz, AC , with outer/inner covercomplete all as specified and directed by Engr In charge/GE |
| 94 | Modular socket combined 2-in-1, 6 Pin 6 & 16 Amps 230 V, 50 Hz, AC , flush typewith outer/inner covercomplete all as specified and directed by Engr In charge/GE |
| 95 | Ceiling rose, surface bakelite 65x 50mm two to three terminals fixed on PVC Round Blockcomplete all as specified and directed by Engr In charge/GE |
| 96 | S&F in replacementsingle pole and neutral enclosure surface mounted 240 voltswith 2 pin and earth plug and socket with one single pole MCB 20 Amps with indicator ofcomplete all as specified and directed |
| 97 | Supply and fixing in replacement LED lights fitting 1x 20W, 230V,AC decorative box typewarm white colour with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engineer-in-Charge/GE |
| 98 | S&F in replacement 36W (2 x 2) LED Ceiling/recess lightpanel for recess mounting warm white colour which provides soft-light and glare free symmetrical illumination complete all as specified and directed by Engineer-in-Charge/GE |
| 99 | S&F in replacementSheet metal enclosure double door type for MCCB TPNDB upto 125 Amps, 4 wayvertical type 415 volts with 400 Amps rated busbar and neutral link including chases wall for fixing DB and making good distributed wall surfaces to match with existing specificationcomplete all as specified and directed. |
| 100 | S & F replacementMCCB Three Pole & Neutral capacity of 125 amps 415 volts rupturing capacity 16 KA complete all as specified and as directed. |
| 101 | S&F in replacementSheet metal enclosure MCB distribution boardsingle pole & neutral 240 volts 08 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link,fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.(Note-MCBs will be measured separately) |
| 102 | S & F in replacement MCBsingle pole 240 volt any rating from 10 to 40 amps \"C\" series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable. |
| 103 | S & F in replacement MCBsingle poleand neutral 240 volt any rating from 63 Amps \"C\"series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable. |
| 104 | Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 6 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable6 Sq mm as earth lead all as specified. Including taking down old sub main wire. Make:Havells/polycab/Finolex |
| 105 | Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 10 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable6 Sq mm as earth lead all as specified. Including taking down old sub main wire, complete all as specified and as directed. |
| 106 | LEDbuilding securitylight fitting 30 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp,clamps,suitablebracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed. |
| 107 | Exhaust fan, steel body AC single Phase. 230V of size 450mm sweep with, blades, and frame and louvers along with all electrical wire connection all as specified and direceted by Engr-in-charge/GE |
| 108 | Ceilingfan, AC single Phase. 230V of size 1200mm sweep with, blades, and frame along with all electrical wire connection all as specified and direceted by Engr-in-charge/GE. |
| 109 | Earthing complete with galvanized steel earth plate electrodes 600 mmx600 mm x6.3 mm thick buried directly in ground earth plate not less than 2.25 m deep below normal ground level with top edge of the plate not less than 1.5 m below normal ground level connected to and including galvanized steel earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and steel including PCC pit in PCC 1:2:4 type B-1using 20 mm graded crushed stone aggregate, RCC framewith 40mm thick RCC cover reinforced with 8mm dia deformed barshandle. including excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mesh and light grade GI protection pipe 15mm bore main board complete all as shown in electrical plate No 5connected to main control board all as specified and testingon completion. Note: Excavation earthwork charcoal PCC pit is covered under this item including taking out existing earth plate etc.Note: if earth resistance of earthing is not found (2 to 5 Ω) satisfactory if will be redone by the contractor on his risk and cost. |
| 110 | Fixing & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with \"XLPE\" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 25 Sqmmx 3.5 coresize all as specified including taking down old cable, complete all as specified and as directed.Note : Earth work and other connected work shall be measured & paid sperately. |
| 111 | Excavation in trenches and exceeding 1.5m wide and not exc 1.5m in depth in hard and dencesoiland getting outcomplete all as specified and directed by Engr In Charge/GE. |
| 112 | Returing, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed. |
| 113 | Removing excavatedmaterial (soil)to a distance not exc 50m and depositing where directed at a level not exc 1.5 m above the startingpoint complete all as specified and as directed. |
| 114 | Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete all as specified and as directed. Note : for payment purpose punned thickness shall be measured |
| 115 | Bricks sub class \"B\"brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels complete all as specified and as directed. |
| 116 | Supply and fixingin repairs GI tubing light grade 40 mm dia along the wall/ in trenches/ in duct / in culvert /road crossing and includingprovisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles complete all as specified and as directed. |
