|
| 1 | Dismantling manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge: bituminous road |
| 2 | Dismantling manually/by mechanical means including stacking of servicable material & disposal of unservicable material with in 50 m lead as per direction of Engineer in charge : Water Bound Macadam |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-incharge. All kinds of soil |
| 4 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge; in cement mortar |
| 5 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. For culverts |
| 6 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 7 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub-grade. |
| 8 | Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings as per direction of engineer-in-charge |
| 9 | Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.With material conforming to Grade-II (size range 53 mm to 0.075 mm) having CBR Value-25 |
| 10 | Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, coarse aggregate not exceeding 26.5 mm nominal size, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per Table: B below, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined by trial during construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a mechanical paver, compacting with 8-10 tonnes vibratory roller, finishing and curing etc. complete as per direction of Engineer-in-charge. Aggregate Gradation for Dry Lean Concrete Sieve Designation Percentage by weight passing the sieve26.5 mm10019.0 mm75-959.50 mm50-704.75 mm30-552.36 mm17-42600 micron 8-22300 micron 7-17150 micron 2-1275 micron0-10 |
| 11 | Providing and laying of separation Membrane of impermeable plastic sheeting 125 micron thick. |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form work for :Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets,kerbs and steps etc. |
| 13 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Mild steel and medium steel bars |
| 14 | Providing and laying of cylindrical Plastic Sheathing of ID 25 mm to 40 mm and 300mm length with necessary compressible material etc.all complete as per direction of Engineer-in-Charge |
| 15 | Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level.; Thermo Mechanically Treated bar of grade 500D or more |
| 16 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 17 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 18 | Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with OPC 43 grade cement, coarse and fine aggregate satisfying Table: A below, conforming to IS 383, maximum size of coarse aggregate 31.5mm nominal size mixed in a automatic batching and mixing plant/machine as per approved Mix design to achieve required design mix grade of controlled concrete including transporting to site in transit mixer, pumping, laying, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, admixtures (IS: 9103 & IS : 6925) etc. with flexural strength minimum 4.5 MPa complete all as per direction of Engineer-in-charge including providing dowel bars with sleeve and tie bars wherever required (Item of joint fillers, sealants, dowel bars with sleeve and tie bars to be paid separately). Aggregate Gradation for Pavement Quality Concrete(Combined Gradation of fine and coarse aggregates)Sieve Designation Percentage by weight passing the sieve31.5 mm 10026.5 mm 85-9519.0 mm 68-889.5 mm 45-654.75 mm30-55600 micron8-30150 micron5-1575 micron 0-15 1.Cement content considered is @ 390 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately.2.It is the responsibility of the contractor to bring the cement concrete manufactured in automatic batching plant (RMC plant) including transportation to site in transit mixer and the quoted rate shall include the expenditure towards the same.3.It is also the responsibility of the contractor to carry out the Design Mix of Cement Concrete as per the specification above from a Govt. Engineering College and get it approved from FCI. The quoted rate shall include the fees of for carrying out the design mix charged by Government Engineering College, cost of material required to carry out the Design Mix and other incidental expenditures.4.Dowel bars, Tie bars and Sleeve (Plastic sheeting) shall be paid under respective items. |
| 19 | Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured) :From brick work in cement mortar Bricks |
| 20 | Laying of thick bed of brick by well ramming and consolidating including necessary excavation, levelling & dressing & finishing the top smooth in foundation and plinth. Bricks supplied free of cost. |
| 21 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 22 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand) |
| 23 | Providing and layingfactory made chamfered edge cement concretepaver block of required strength, thickness & size/shapemade by table vibratory method to attain superior smooth finish using PU or equivalent mould laid in grey colour or pattern over50mm thick compacted bed of coarse sand, filling compacting/ proper embedding/ laying of interlocking paver blocks in to the sand bedding layer through vibratory campaction by using plate vibrator filling the jointswith yamuna & cutting of paver blocks as per required size & pattern finishing & sweeping extra sand in footpath,parks, lawns, drive ways or light traffic parking etc. all complete as per the manufacturer\"s specification &direction of Engineer-in-charge. (a) 80 mm thick cc paver block of M-35 grade with approved colour design & pattern. |
| 24 | Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.) |
| 25 | Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge. Using grade \"A\" sealing compound conforming to IS: 1834 |
| 26 | Credit of stone aggregate obtaind from excavated WBM materials |
| 27 | Disposal of building rubbish/malba/similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by the Engineer-in-charge, beyond 50 metre initial lead, for all leads including all lifts involved. |
