Tender For Construction Of Urban Health And Wellness Centre Under Abhim At Chakkargaon Under Sd-Iv, Cd-Ii, Apwd, Prothrapur. (Civil Work)
Tender Value
1.52 Crore
Estimated cost
Bid Submission
18 Sep 2024
0 days left
EMD
3.04 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Prothrapur → Andaman And Nicobar Islands
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Urban Health And Wellness Centre Under Abhim At Chakkargaon Under Sd-Iv, Cd-Ii, Apwd, Prothrapur. (Civil Work)
BOQ
| Sl. No. | Item Description |
| 1 | Earthworkinexcavationbymechanicalmeans(Hydraulicexcavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. |
| 2 | All kinds of soil |
| 3 | Earth work in excavation by mechanicalmeans (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 4 | All kinds of soil. |
| 5 | Fillingavailableexcavatedearth (excludingrock)intrenches,plinth.sidesof foundationsetc.inlayersnotexceeding 20cmindepth,consolidatingeach deposited layer by ramming and watering, lead up to 50 m and for all lift |
| 6 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 7 | Supplying chemical emulsion in sealed containers including delivery as specified. |
| 8 | Chlorpyriphos emulsifiable concentrate of 20% |
| 9 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : (a) Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.: |
| 10 | With ChlorpyriphosE.C. 20% with 1% concentration |
| 11 | Providingandlayinginpositioncementconcreteof specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 12 | 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 13 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 14 | Providing and fixing up to floor five level precast cement concrete string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, etc., including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of required Centering complete. |
| 15 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20mm nominal size derived from natural sources) |
| 16 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) |
| 17 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. |
| 18 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 19 | Providing hollow block walling upto floor V level 200mm thick consiting of using hollow block of size 400 x 200 x 200 mm of mix 1:3:6 (1 Cement: 3 Course Sand : 6 stone aggregate 20 mm nominal size) having a cruching strength of 3.5 N/Sqm at 28 days as per IS:2185 (part-I) 1979 laid in cement morter 1:6 (1 Cement :6 Course Sand) complete. |
| 20 | Providing hollow block walling upto floor V level 100mm thick consiting of using hollow block of size 400 x 100 x 200 mm of mix 1:3:6 (1 Cement: 3 Course Sand : 6 stone aggregate 20 mm nominal size) having a cruching strength of 3.5 N/Sqm at 28 days as per IS:2185 (part-I) 1979 laid in cement morter 1:6 (1 Cement :6 Course Sand) complete. |
| 21 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : |
| 22 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) |
| 23 | Reinforcedcement concreteworkinwalls(any thickness), includingattachedpilasters,buttresses,plinthandstring courses, fllets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement: |
| 24 | 1:1.5:3 (1cement :1.5 coarsesand(zone-III)derivedfrom natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 25 | Reinforced cement concrete work in beams, suspended foors, roofshavingslopeupto 15°landings,balconies,shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 26 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 27 | Foundations, footings, bases of columns, etc. for mass concrete. |
| 28 | Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 29 | Suspended floors, roofs, landings, balconies and access platform |
| 30 | Shelves (Cast in situ) |
| 31 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 32 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 33 | Stairs, (excluding landings) except spiral-staircases |
| 34 | Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards |
| 35 | Weather shade, Chajjas, corbels etc., including edges |
| 36 | Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1cement: 3finesand)etc.complete,excluding plastering of the jambs, sills and sofits. |
| 37 | 50 mm thick |
| 38 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 39 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 40 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. |
| 41 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 42 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanitycounters,windowsills,faciasandsimilarlocationsof required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. (a) Granitestoneslabofallcolourandtextureexceptblack, Cherry/Ruby red |
| 43 | Area of slab over 0.50 sqm |
| 44 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 45 | Granite work |
| 46 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 47 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. |
| 48 | Fixed to openings /wooden frames with rawl plugs screws etc. |
| 49 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 50 | 300x16 mm |
| 51 | 250x16 mm |
| 52 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 53 | 300x10 mm |
| 54 | 200x10 mm |
| 55 | 100x10 mm |
| 56 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 57 | 125 mm |
| 58 | 100 mm |
| 59 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 60 | Twin rubber stopper |
| 61 | Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 62 | Providing and fixing PTMT door catcher of length 72 mm and dia. of 42 mm with suitable washers weighing not less than 33 gms |
| 63 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). |
| 64 | Category-I Padauk |
| 65 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including IS: 12817 marked stainless steel butt hinges of required size with necessary stainless steel screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (a) Category-I Padauk |
| 66 | 35 mm thick shutters |
| 67 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. |
| 68 | Category-I Padauk |
| 69 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including IS: 12817 marked stainless steel butt hinges of required size with necessary stainless steel screws. (a) Superior Hard Wood Category-II (A) (Black Chuglam, Thingam, Toungpeing, Pylnma, Koko and Mahwa) |
| 70 | 35 mm thick |
| 71 | Providing& Fixing 18 mm thick, 150 mm wide pelmet made of wooden plastic component (WPC) board, including top cover of 06 mm WPC board, 2 Nos. Readymade Stainless Steel Clamp & 20mm dia Stainless Steel (heavy duty) curtain rod with all necessary screws/nails etc all complete as per directions of Engineer-in-Charge. |
| 72 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 73 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 74 | Steel work in built up tubular (round, square or rectangular hollow tubesetc.)trussesetc.,includingcutting,hoisting,fixingin position and applying a priming coat of approved steel primer, including welding andbolted withspecial shaped washers etc. complete. |
| 75 | Electric resistance or induction butt welded tubes |
| 76 | Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete. |
| 77 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. |
| 78 | Providing and fixing bolts including nuts and washers complete. |
| 79 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 80 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 81 | 40 mm thick with 20 mm nominal size stone aggregate |
| 82 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete. |
| 83 | Size of Tile 600x600 mm |
| 84 | Providing and fixing plain multipurpose cement board(Hight pressure steamcured)withsuitablescrewsforcementparticleboardin ceiling etc. complete (frame work to be paid seperatately). |
| 85 | 6 mm thick Cement fiber board, Type-B, Category-III as per IS: 14862:2000 |
| 86 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 87 | 110 mm diameter |
| 88 | Providing and fixing onwall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 89 | Coupler (a) 110 mm |
| 90 | Bend 87.5°(a) 110 mm bend |
| 91 | Providingandfixingunplasticised PVCpipeclipsof approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mmhard wood plugs,screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete. |
| 92 | 75 mm |
| 93 | 110 mm |
| 94 | Providing and fixing to the inlet mouth of rain water pipe PTMT (an Engineering Thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighing not less than 100 gms. |
| 95 | Providing and fixing pre-printed galvanune (PPGL)steel profile sheets AZ-150 of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd or equivalent(size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 150 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws (Xylan) of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 96 | Providing and fixingpre-printed galvanune (PPGL)steel profile sheets AZ-150 of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal India Ltd or equivalent roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : |
| 97 | Ridges plain (500-600mm) |
| 98 | Barge board (upto 300 mm) |
| 99 | 12 mm cement plaster of mix : |
| 100 | 1:4 (1 cement: 4 fine sand) |
| 101 | 15 mm cement plaster on the rough side of single or half brick wall of mix : |
| 102 | 1:4 (1 cement: 4 fine sand) |
| 103 | 12 mm cement plaster finished with a floating coat of neat cement of mix : |
| 104 | 1:3 (1 cement: 3 fine sand) |
| 105 | 6 mm cement plaster of mix : |
| 106 | 1:3 (1 cement : 3 fine sand) |
| 107 | Distemperingwith 1stqualityacrylicdistemper (ready mixed)havingVOCcontentlessthan50gram/litre,of approved manufacturer, of required shade and colour all complete: |
| 108 | New work (two or more coats) over and including water thinnableprimingcoat withcement primerhavingVOC content less than50 pram/litre |
| 109 | Finishing walls with Acrylic Smooth exterior paint of required shade . |
| 110 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm |
| 111 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer\"s specifications including appropriate priming coat, preparation of surface, etc. complete. |
| 112 | On steel work |
| 113 | On concrete work |
| 114 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 115 | Two or more coats on new work |
| 116 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 117 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. |
| 118 | Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade |
| 119 | Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarsesand) in all shapes & patterns including grouting the joints with whitecement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. |
| 120 | Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlle ddevice (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: |
| 121 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 122 | Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : |
| 123 | W.C. pan with ISI marked white solid plastic seat and lid |
| 124 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: |
| 125 | White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 126 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required : (a) Kitchen sink with drain board |
| 127 | 510x1040 mm bowl depth 250 mm |
| 128 | Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete,including painting of fittings and brackets, cutting and making good the wall wherever required : |
| 129 | Size 600x450x200 mm |
| 130 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 131 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. (a) Semi rigid pipe |
| 132 | 32 mm dia |
| 133 | Providing and fixing 100 mm sand cast Iron grating for gully trap. |
| 134 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard boardground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 135 | Providing and fixing 600x120x5 mm glass shelf with edges round off,supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawlplugs etc., complete. |
| 136 | Providing and fixing toilet paper holder: |
| 137 | C.P. brass |
| 138 | Providing and fixing soil, waste and vent uPVC pipe conforming to HSN Code 3917 single socket Type B, including solvent joint. |
| 139 | 110 mm diameter |
| 140 | 75 mm diameter |
| 141 | Providind and fixinguPVCmoulded fittings/ accessories conforming to HSN Code 3917, including joint with solvent. |
| 142 | Door bend of required degree (a) 110mm |
| 143 | Door bend of required degree (b) 75mm |
| 144 | Single tee with door (a) 75 x 75 x 75 mm |
| 145 | Single tee with door (b) 110 x 110 x 110 mm |
| 146 | Providing and fixing 600mm long C.P brasstowel railwith brackets fixed with necessary CP brass screws of approved quality. |
| 147 | Providing and fixing S.S Soap Dish with necessary S.S screws of approved quality. |
| 148 | Providing and fixing floor trap 100mm round shape doom type stainless steel grating for gully trap. |
| 149 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings withonestep CPVCsolvent cementandthe cost of cutting chasesandmaking good thesame including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 150 | 20 mm nominal dia Pipes |
| 151 | 25 mm nominal dia Pipes |
| 152 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work |
| 153 | 40 mm nominal dia Pipes |
| 154 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : |
| 155 | 100 mm diameter |
| 156 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 157 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. |
| 158 | 15 mm nominal bore |
| 159 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 160 | 15 mm nominal bore |
| 161 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 162 | 15mm nominal bore |
| 163 | Providing and fixing Chrome PlatedHealth Faucet with 1.0/1.2mFlexible Tube and hook complete of make Jaquar, Prayag, parryware or equalient. |
| 164 | Providing and fixing 15 mm nominal bore C.P. brass2-way Bib Cockwith Wall Flange of approved quality make Jaquar, Prayag, Parryware or equalient. |
| 165 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement:3coarsesand)finishedwithfloating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : (a) Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : |
| 166 | With common burntclay F.P.S. (non modular)bricks of Class designation 7.5 |
| 167 | Constructing brickmasonry road gully chamber 50x45x60 cm withbricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mmpre-cast R.C.C.horizontalgrating with frame complete as per standard design : |
| 168 | With common burnt clay F.P.S. (nonmodular)bricks of class designation 7.5 |
| 169 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 170 | With commonburnt clay F.P.S. (non modular)bricks of class designation 7.5 |
| 171 | Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in- charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). |
| 172 | Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer-in-charge. |
| 173 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured. |
| 174 | Providing and fixing factory made single extruded WPC (Wood PolymerComposite)soliddoor/window/ClerestoryYvindows& other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (woodpowder/ricehusk/wheathusk)andnontoxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2,modulusofelasticity900N/mm2andresistanceto spreadofflameof ClassAcategorywithpropertyof being termite/borer proof, water/moisture proof and fire retardant and fixedinpositionwithM.Shold fast/lugs/SS dashfasteners of required dia and lengthcomplete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance indimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 175 | Frame size 65 x 100 mm |
| 176 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimumcompressive strength50 N/ mm2, modulus of elasticity 850 N/mm2 and resistance to spread offlame of Class Acategory with property of being termite/ borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 177 | 30 mm thick |
| 178 | 35 mm thick |
| 179 | Providing cement concrete surface drain including earthwork excavation 10 cm thick base concrete and 15 cm thick side wall 1:3:6 (1 cement : 3 Coarse sand : 6 graded stone aggregate of 40 mm nominal size) cement concrete finished with 12mm thick 1:4 (1 cement : 4 sand) finished with a floating coat of neat cement inside the drain and its top and exposed surface and disposal surplus earth etc. complete |
| 180 | 23 cm x 23 cm |
| 181 | Providing and fixing PVC pipe weep hole at 1.0 mtr interval on both direction (Horizontal & Vertical ) in zig zag Shape or as per the direction of Engineer-in-Charge. |
| 182 | 75mm dia. |
| 183 | Providing and laying Polyethylene Septic tank for 30 -35 flushing/day made of polyethylene in a single moulding with 3 chambers and 2 manholes, the high wall/thickness of septic tank should with stand load and pressure of the earth to a greate extent , fulfilling the technical specification of Type-III United Polyethylene Septic tank or equivalent capacity of flushing per day should be 30-35 , diameter of tank 1000mm, length 2800 mm, minimum thickness 10mm, number of chamber 2, number of manhole 1 No. of size 500 mm (Dia) and Air vent pipes of 50mm dia etc. all complete laid as per the direction of Engineer-in-Charge. (Note : Earth work in excavation, cement concrete bed & vent pipe shall be paid separately). |
| 184 | Providing and applying Dr. Fixit water proof seal compound with one layer/coat of Dr. Fixit prime seal (adhesive) (dilution with potable water by volumn in 2:1 ratio) and two coats of Dr. Fixit newcoat (heavy duty reinforced Acrylic waterproof coating for terrace) after scrapping and properly cleaning the surface to removeloose particiles with wre brushes, complete in all respect as per the direction of Engineer-in-charge (Note: scrapping and properly cleaning the surface to remove loose particles shall be paid separately) |
AI Tender Summary
Tender Timeline
Aug 16, 2024
11:30 IST
Tender Published
Tender notice published.
CompletedSep 18, 2024
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedSep 19, 2024
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender