|
| 1 | Earth work in excavation : Labour only for earth work in excavation in foundation, in foundation trenches etc., not exceeding 1.50 m wide and not exceeding 1.5 min depth getting out in hard or dense soil as ordered by EIC/SIC. |
| 2 | Returning, filling: Labour only for returning, filling in, of soft disintegrated soil including spreading, levelling, watering and well ramming in layers not exc 25 cm. as ordered by EIC/SIC. |
| 3 | Removal of spoil: Labour only for removal of spoil mixed with excavated earth, broken bricks, concrete rubbish and debris, broken glasses from work site to a distance of 1.50 km. outside the factory or as directed by the EIC/SIC (20% deduction in measurement will be made from the volume of spoil ). |
| 4 | P.C.C (1:2:4) : M & L for providing plain cement concrete type-B1, 1:2:4 mix ( using 20 mm graded stone aggregate ) as in sub-base, filling and mass concrete as ordered by EIC/SIC. |
| 5 | R.C.C (1:1.5:3).: M & L for providing reinforced cement concrete type M-20, 1:1.5:3 mix (using 20 mm graded stone aggregate) as in foundation, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, precast slab etc.as ordered by EIC/SIC. |
| 6 | Cutting holes:Labour only for Cutting holes exc. 150 sq.cm and not exceeding 400 sq. cm into or through brick walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as require and ordered by EIC/SIC. |
| 7 | Brick work(1:6): M & L for brick work with old size subclass\"B\" bricks, straight or curved on plan exc 6m mean radius with (1: 6) cement morter as ordered by EIC/SIC. |
| 8 | Form work : Use & waste of wooden form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, cast iron slab, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. similar work complete as ordered by EIC & SIC. |
| 9 | MS work: M & Lfor providing rolled mild steel angle, tee, flat, chanel etc. sections, erection, fabrication & fixed at any position as ordered by EIC/SIC. |
| 10 | M.S small articles : S & F for providing mild steel straps, clamps, hold fasts, hinges etc, as small articles,to be fixed in position as required as ordered by EIC/SIC. |
| 11 | Reinforcement : M&L for providing reinforcementwork with TMTmild steel bars 08 mm and over, cut to length, bent to shape required, including cranking, bending, hooking ends & binding with mild steel wire (annealed) not less than 0.9 mm dia. etc.complete as ordered by EIC/SIC. |
| 12 | MSPlate/sheet: S & F ofmild steel plate of Fe-410-W(Gde- E-250) quality B, (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes,including fabrication and erection for valve chamber plate or similar works or foundation plate etc. complete as ordered by EIC/SIC. |
| 13 | Neat cement finish : M & L for applying cement slurry about 1.5 mm thick on plastared or concrete surface to have the surfaces even & smooth as ordered by EIC/SIC. |
| 14 | Chequered cement concrete tiles: M & L for providing Chequered cement concrete tiles 20cm x 20cm x 25mm thick, with grey pigment cement and pigment, jointed and pointed in neat cement slurry in floors as ordered by EIC/SIC. |
| 15 | Cement plaster(1:6): M & L for providing 12 mm thick cement plater 1:6 mixon fair faces of brick work or concrete surfaces at any height as ordered by EIC/SIC. |
| 16 | Exterior surface painting :Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having with [make: of 1st quality of Asian/Berger/ICI or substantially equvalant] VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm after necessary preparation of surfaceall complete and all as ordered by EIC/SIC. |
| 17 | Washable distempering: M & L for applying two coat of washable distemper of 1st quality; [Make: Asian / Berger / ICI or substantially equvalant] , and approvedshade after necessary preparatory work and primer to distempering on wall and ceiling surfaces as ordered by EIC/SIC. |
| 18 | Steel painting two coat: M & L for applying two coats of synthetic enamel paint finished glossy of 1st quality; Make: Asian / Berger / ICI or substantially equivalent make, and approvedshade over a coat of priming with red lead primerafter necessary preparation of new decorated steel surfaces of any description over 10 cm width or girth as ordered by EIC/SIC. |
| 19 | Single brick flat soling : M & L for providing single brick flat soling with well burnt soling brick including filling of interstices with white sandas ordered by EIC/SIC. |
| 20 | Demolition of PCC : Labour only for demolition of cement concrete of any description and in any position and removing the same out off the work site as orderd by EIC/SIC. |
| 21 | Dismantling steel work : Labour only for Dismantling structural steel work including doors, gates but excluding framed truss etc. and removing the same to store or as directed by the EIC/SIC. |
| 22 | Demolition of brick work: Labour only for demolition of brick work or stone/boulder masonry of any typebuilt in cement morter including all quoins, arches, pillars etc as order by EIC & SIC. |
| 23 | DI /CI Bend, Tee etc: Providing and laying / or welding in tthe existing line if required upto 300 mm dia. S&S C.I. standard specials / all fittings such as bend, Tee, collars, flange, tapers, caps, adopter, nut bolt, connecting pieces one end flanged and other socket or spigot and bell mouth pieces one end flanged other end tapering as bell mouth etc. (heavy class) which ever is required complete as per requirement and direction of Engineer-in-charge. |
| 24 | Cutting cast iron/DIpipes of 150mm dia: Labour only for cutting cast iron/DI pipes of 150mm diafor insertion of new tees, valves, branches, etc complete as ordered by EIC/SIC. |
| 25 | GI pipe 50 mm dia :S & F of 50 mm bore dia Tubes ( Make: TATA / JINDAL/ BHUSAN or substantially equvalant), \"Medium grad\", galvanised, with all fitting; laid in trenche laid or fixed in proper positionincluding short lengths, with all pipe fittings such as union, ends, elbows, tees, reducingtees, adoptors, sockets, plugs, hose clips etc. and fixing to walls / trenches etc, complete with saddles (snap clips), wall clips, hooks, protective mild steel tube sleeves and cutting through walls,floors and their making good or laying in trenches and also cutting, screwing and waste complete as ordered by EIC/SIC. |
| 26 | GI pipe 40 mm dia :S & F of 40 mm bore dia Tubes ( Make: TATA / JINDAL/ BHUSAN or substantially equvalant), \"Medium grad\", galvanised, with all fitting; laid in trenche laid or fixed in proper positionincluding short lengths, with all pipe fittings such as union, ends, elbows, tees, reducingtees, adoptors, sockets, plugs, hose clips etc. and fixing to walls / trenches etc, complete with saddles (snap clips), wall clips, hooks, protective mild steel tube sleeves and cutting through walls,floors and their making good or laying in trenches and also cutting, screwing and waste complete as ordered by EIC/SIC. |
| 27 | GI pipe 25 mm dia :S & F of 25 mm bore dia Tubes ( Make: TATA / JINDAL/ BHUSAN or substantially equvalant), \"Medium grad\", galvanised, with all fitting; laid in trenche laid or fixed in proper positionincluding short lengths, with all pipe fittings such as union, ends, elbows, tees, reducingtees, adoptors, sockets, plugs, hose clips etc. and fixing to walls / trenches etc, complete with saddles (snap clips), wall clips, hooks, protective mild steel tube sleeves and cutting through walls,floors and their making good or laying in trenches and also cutting, screwing and waste complete as ordered by EIC/SIC. |
| 28 | GI pipe 15 mm dia :S & F of 16 mm bore dia Tubes, \"Medium grad\", galvanised ( Make: TATA / JINDAL/ BHUSAN or substantially equvalant), with all fitting; laid in trenche laid or fixed in proper positionincluding short lengths, with all pipe fittings such as union, ends, elbows, tees, reducingtees, adoptors, sockets, plugs, hose clips etc. and fixing to walls / trenches etc, complete with saddles (snap clips), wall clips, hooks, protective mild steel tube sleeves and cutting through walls,floors and their making good or laying in trenches and also cutting, screwing and waste complete as ordered by EIC/SIC. |
| 29 | UPVC pipe 50 mm dia : S & F of 50 mm bore dia Unplasticiscd PVC pipes [Make: Oriplast / Supreme / Finolex or substantially equivalent ] of pressure rating 10 kgf/cm2 to walls, ceilings or in floors etcincludingall pipe fittingsshort lengths, with all pipe fittings such as union, ends, elbows, tees, reducingtees, adoptors, sockets, plugs, hose clips etc. and fixing to walls etc, complete with saddles (snap clips), wall clips, hooks and also cutting, screwing and waste.complete as ordered by EIC/SIC. |
| 30 | UPVC pipe 40 mm dia : S & F of 40 mm bore dia Unplasticiscd PVC pipes of pressure rating 10 kgf/cm2 laid in trenche or fixed in proper positionincludingall pipe fittingslaying in trenches and also cutting, screwing and waste.complete as ordered by EIC/SIC. |
| 31 | UPVC pipe 25 mm dia : S & F of 25 mm bore dia Unplasticiscd PVC pipes of pressure rating 10 kgf/cm2 laid in trenche or fixed in proper positionincludingall pipe fittingslaying in trenches and also cutting, screwing and waste.complete as ordered by EIC/SIC. |
| 32 | UPVC pipe 15 mm dia : : S & F of 15 mm bore dia Unplasticiscd PVC pipes of pressure rating 10 kgf/cm2 laid in trenche or fixed in proper positionincludingall pipe fittingslaying in trenches and also cutting, screwing and waste.complete as ordered by EIC/SIC.. |
| 33 | Stop valves 50 mm dia: S & F of 50 mm dia Stop valves ( Make: NETA / ZOLOTO / ALTO or substantially equvalant) , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixedin proper position complet as ordered by EIC/SIC. |
| 34 | Stop valves 40 mm dia: S & F of 40 mm dia Stop valves ( Make: NETA / ZOLOTO / ALTO or substantially equvalant) , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixedin proper position complet as ordered by EIC/SIC. |
| 35 | Stop valves 25 mm dia: S & F of 25 mm dia Stop valves ( Make: NETA / ZOLOTO / ALTO or substantially equvalant), cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixedin proper position complet as ordered by EIC/SIC. |
| 36 | Stop valves 15 mm dia: S & F of 15 mm dia Stop valves ( Make: NETA / ZOLOTO / ALTO or substantially equvalant), cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixedin proper position complet as ordered by EIC/SIC. |
| 37 | Bib taps: S & F of Bib taps of Make: Alto/ Zolota / Neta or substantially equvalan, castcopper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed bib taps size of tap 15 mm bore dia. as ordered by EIC/SIC. |
| 38 | Bib taps fancy type : S & FBib taps of fancy type cromium plated of Make: Hindware / Neycer / Parryware or substantially equivalen of reputed brand screwed for iron pipe or for brass and fixed, size of tap 15 mm bore dia. after taking out old existing tap as ordered by EIC/SIC. |
| 39 | Tapping point including ferrule : M & Lfor providing Drilling and tapping DI water mains (in position) for branch connections of 20mm internal dia. including straight plain brass ferrules (or connecting screws) screwed both ends and fixed as ordered by EIC/SIC. |
| 40 | DI Pipe: M & L for ductile iron pressure pipe 100 mm dia (including required nos. of 100mm dia bend and Tee) centrifugally cast with socket & spigoted end Class K-9, ISI marked duly embrossed suitable for (push on joint) rubber gusket D joining with inside cement mortar lining outside zinc coating with bitumen finishing layer including joining materials and making good the disturbed surfaces of roads,path ways etc complete as per requirement and direction of Engineer-in-charge. |
| 41 | Sluice valve 100mm dia: M & L forDI/CI Sluice valve with flanged ends of class PN 1.6 of size 100mm dia bore and fixed the same with the exising pipe line completeas per requirement and direction of Engineer-in-charge. |
