Tender For Civil Work For Installation Of One No. 3 H.P. Tube Well Boring At 132 Kv S/S Ghatampur, Kanpur Nagar. (Pr No. 1300052624/2024), 1 Earth Work In Excavation By Mechanical Means (Hydraulic Excavator) / Manual Means In Foundation Trenches Or Drai

Sharing tender

Tender For Civil Work For Installation Of One No. 3 H.P. Tube Well Boring At 132 Kv S/S Ghatampur, Kanpur Nagar. (Pr No. 1300052624/2024), 1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. ( code no. 2.8.1) 2 Providing and laying in position,1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :. ( code no. 4.1.10) 3 Providing and fixing up to floor five level precast cement concrete solid block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete :1:1½:3 (1 Cement: 1½ coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). (code no.- 4.7.1) 4 Mild steel and Medium Tensile steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.(code no.- 5.22A.1) 5 Brick work with cement mortar 1:4 (1 cement : 4 coarse sand) common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth (code no.- 6.1.1) 6 12 mm cement plaster of mix 1:4 (1 cement: 4 fine sand)(code no.- 13.1.1) 7 Providing and fixing 20mm dia G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.(code no.-18.10.2) 8 Providing and fixing 25mm dia G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.(code no.-18.10.3) 9 Providing and fixing 40mm dia G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.(code no.-18.10.5) 10 Making connection of G.I. distribution branch with G.I. main of 25 to 40 mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete :(code no.-18.13.1) 11 Providing and fixing 25mm dia gun metal gate valve with C.I. wheel of approved quality (screwed end) (code no.-18.17.1) 12 Providing and fixing 40mm dia gun metal gate valve with C.I. wheel of approved quality (screwed end) :(code no. 18.17.3) 13 Providing and fixing 40 mm nominal bore Horizontal gun metal non- return valve of approved quality (screwed end).(code no.-18.19.3.1) 14 Boring/drilling bore well of 400 mm dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. (code no.-23.1.1.3) 15 Same as above item no. 13 but beyond 90 metre & upto 150 metre depth below ground level..(code no.-23.2.1.3) 16 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of 200 mm nominal size dia conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge (code no. 23.3.3) 17 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) 200 mm nominal size diapipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. (cde no. 23.4.3) 18 Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.(code no.23.8) 19 Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by V notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. (code no.- 23.12) 20 Providing and fixing clamp of 200mm dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. (code no.-23.14.3) 21 Providing and fixing Bail plug/ Bottom plug of 200 mm dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).direction of Engineer-in-charge. (code no. 23.15.3) 22 Supplying and drawing following 3 x 2.5 sq. mm sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.(code no.-28.1) 23 Supplying and fixing of 25 mm of medium class PVC conduit along with accessories in surface/recess including junction box,cutting the wall and making good the same in case of recessed conduit as required. 25 mm (code no.-28.6) 24 Supply and fixing support clamps for 40mm dia column pipesmade out of MS flats, pairs of bolt-nuts etc complete with all material, labour, T&P. (code no.-29.48d) 25 Lowering of M.S. column pipe in tubewell including supply of nuts, and bolts, packing and also carriage of pipe from workshop to site including all labour, T&P etc. required for proper completion of the work..a)80/65/50/40/32 mm dia.( Code no.-29.50) 26 Transportation and installation of tube well drilling Rig m/c, compressure for development and other required equipments and accessories at site of work and dismentlling & taking them back after successful completion of the work including cleaning, levelling - dressing the site properly, also disposing off the surplus earth, silt, sand etc.(CSI No. 29.51) 27 Supply & installation of electrical control panel of L&T / Havells or equivalent make for submersible pump / pumpset containing contractor relay condenser. c) for 3 H.P pump set single phase(code no.-29.54) 28 Supply & Installation ofsubmersible pump of K.S.B/ CALAMA. or eqt. make including cost of labour, T&P and material required for completion of work.d) 3 HP outlet 50/40 mm dia. or more, Head 60/24, Discharge 6000/14000 LPH (code no.-29.55) 29 Supply & fixing of steel wire rope forsubmersible pump including cost of labour, T&P and material required for completion of work.(code no- 29.56)