Tender For Construction Of 2 Unit Toilet Block Of Contai Muslim Girls High School
Tender Value
5.10 Lakhs
Estimated cost
Bid Submission
06 Aug 2024
0 days left
EMD
10209
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
contai → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of 2 Unit Toilet Block Of Contai Muslim Girls High School Construction Of 2 Unit Toilet Block Of Contai Muslim Girls High School (Hs) Under (Mdw) Scheme - 2023-24, Project Id Md232409191s000, At Mouza. Uttar Darua, Ward No. Iv With In Contai Municipality
BOQ
| Sl. No. | Item Description |
| 1 | PWDPage No - 1, Item No.- 2. (a), |
| 2 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.a)Depth of excavation not exceeding 1500 mm |
| 3 | PWDPage No - 1, Item No.- 3(a). |
| 4 | Earthworkinfillinginfoundation trenchesorplinth with good earth, in layers not exceeding 150mm. includingwateringand rammingetc. layerbylayer complete. (Payment to be made on the basis of measurement of finished quantity of work) |
| 5 | P.W.D. Page No.-2, Item No. -4. |
| 6 | (A) Filling in foundation or plinth by fine sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity)(B) Do - by Silver sand |
| 7 | P.W.D. Page No.-14, Item No. -1. |
| 8 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 9 | Page No.- 23 / Item No.- 1(a) |
| 10 | Cement concrete with graded Jhama Khoa (40 mm size excluding shuttering)a)1:3:6 proportion in ground floor & foundation. |
| 11 | Page No.- 41 / Item No.- 33. |
| 12 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevantIS codes.Pakur varity. |
| 13 | P.W.D, Page No.- 26, Item no.- 10(i) |
| 14 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.i) Pakur Variety |
| 15 | P.W.D. Page No.- 43, Item no.- 40(i)(I). |
| 16 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. (a) For works in foundation, basement and upto roof of ground floor/upto 4 m (i) Tor steel/Mild Steel I. SRMB / JSW/ SHYAM/JSPL/BMASL/ELECTROSTEEL/SSL |
| 17 | Page No.- 42 / Item No.- 36 (a) |
| 18 | Hireand labourchargesfor shuttering with centering and necessary staging upto 4mm, using approved scout propsand thickhard woodplanksof approved thicknesswithrequired bracingsfor concreteslabs, columns, lintels,beamsetc. curvedor straight, including fitting, fixing and striking out after completion of works (upto roof of ground floor).a) 25 mmto30mm thick wooden shutteringasper decisionand direction of the Engineer-in- |
| 19 | P.W.D. Page No. -47, Item No.-1, |
| 20 | 25mm. thick damp proof course with cement concrete with stone chips (1:1.5:3) [with graded stone aggregate 10 mm nominal size] and admixture of water proofing compound as per manufacturer\"s specification followed by two coat of polymer based paint, (1st coat after 4 to 5 days of concrete laying and 2 nd coat just before brick masonry work) as directed (cost of water proofing compound & polymer based paint to be paid separately).( Chequering not required over concrete or painted surface). [Note: - Waterproofing as per item 9, polymer based paint as per item 8 (a) of subhead C of Section (C). |
| 21 | Page No.- 15 / Item No.- 8(a) |
| 22 | Brick work with 1st class bricks in cement mortar (1:6)(a) In foundation and plinth |
| 23 | Page No.- 15 / Item No.- 8(b) |
| 24 | Brick work with 1st class bricks in cement mortar (1:6)(b) In superstructure, ground floor |
| 25 | Page No.- 16 / Item No.- 16. |
| 26 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor |
| 27 | Page No. -17,Item No .-21(a) |
| 28 | (a) 75 mm. thick brick work with 1st class bricks set in cement, sand mortar (1:4) in ground floor including H.B. netting in every alternate layers. |
| 29 | Page No. -192, Item No.- 1, |
| 30 | Labour for Chipping of concrete surface before taking up Plastering work. |
| 31 | P.W.D. Page No.- 189/ Item No.- 1(i)(b) |
| 32 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](ii) With 1:6 cement mortar(b) 20 mm thick plaster |
| 33 | (b) 15 mm thick plaster (1:4) |
| 34 | (c) 10 mm thick plaster (1:4) |
| 35 | Page No.-192,Item No.-15 |
| 36 | Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100sq.m. |
| 37 | Page No. -45, Item No.-8 |
| 38 | (b) Applying 2 coats of Non-Toxic Acrylic Polymer modified Paint having adhesive & waterproofing properties by mixing in proportion (1 liquid: 4 cementitious material) or as per manufacturer\"s specification for water proofing layer in water tank etc. (No Departmental Cement is required) |
| 39 | P.W.D. Page No.- 48/ Item No.- 6(iii) |
| 40 | Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concretesurface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. In ground floor. 3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement).Using grey cement(iii) 35 mm. thick |
| 41 | Page No. -74, Item No. 46. |
| 42 | Supplying and laying chequered tiles of any shade & of approved quality with (1:1½:3) cement concrete laid in panels or patterns as directed in pavement, footpath etc. including necessary underlay 25 mm thick [avg] cement mortar (1:3) complete in all respect with all labour and materials. [Using cement slurry @ 4.4 kg/Sq.m at back side and @2.4 kg/Sq.m for joint filling]Red Variety(i) 25 mm. thick |
| 43 | Page No. -64, ItemNo.-35. |
| 44 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles inclu-ding roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (a) Area of each tile upto0.09 Sq.m (ii) Other than Coloured decorativeincluding white |
| 45 | (B) WALLWith Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.(a) Area of each tile upto 0.09 Sq.m(ii) Other than Coloured decorative including white |
| 46 | Page No. -194, Item.No.-4 |
| 47 | Colour washing with any shade with Stainers, as required including cleaning and smoothening surface thoroughly :(ii) External surface (Ground floor)(b) Two Coats(i) Other than yellow, pink |
| 48 | Page No. -194, Item.No.-4 |
| 49 | Colour washing with any shade with Stainers, as required including cleaning and smoothening surface thoroughly :(i) Internal surface (All floors)(b) Two Coats(i) Other than yellow, pink. |
| 50 | Page No. -194, Item.No.-4 |
| 51 | Supplying fitting and fixing in position approved P.V.C. door frame (Matt finish) made of extruded P.V.C. multichamber hollow section having dimensions 60mm x 50mm x 2mm (+/- 0.2mm), horizontal section will be joined with vertical section by galvanised steel screws after inserting two number steel brackets as reinforcement making suitable space for placing hinges, one steel tube 40mm x 20mm x 1.20 mm will be inserted on one full vertical side of the frame (hinge side) as reinforcement, the frame will then be fixed in the opening with the help of P.V.C. expandable fastner/wooden gutties and galvanised steel screws including cost of all materials and labour, hire charges of tools and appliances, carriage of all materials, taxes and all other incidental charges complete |
| 52 | Page No. -134, Item No.-27 |
| 53 | PVC Door Shutter-30 mm thick: Supplying fitting and fixing P.V.C. door shutter of approved quality & shade in position, the style & rail of the P.V.C. door shutter will be made of rigid P.V.C. multicavity hollow chamber of 59 mm x30 mm section with 2.0 mm (+/-0.2 mm) wall thickness.Horizontal & vertical section shall be fixed to each other by self tapping screws and 1 solid polymeric or M.S. galvanised tubular \"L\" shaped bracket 100mm x 200mm in each corner of the shutter frame for placing hinges. Polymer based multicavity hollow section of 120 mm x30mm with 2.0 mm (+/- 0.2 mm) wall thickness will be fitted in the middle, reinforced by solid polymer bar of 200 mm long at both ends and screws from both sides as lock rail. The section frame will then be fitted in by PVC panels of size 100 mmx25 mm with wall thickness of 1.2 mm (+/- 0.2 mm) and 2 nos. of 6 mm dia bright rod will be inserted horizontally with both side check and nut system and stretches where fixing of hinges / hasp bolt / tower bolt / door ring are required to be strong enough to with stand wear and tear. The rate is inclusive of cost of all materials, labour, and hire of tools and plants and appliancesi/c carriage of all |
| 54 | Page No. -40, Item No.-28,(b) |
| 55 | Precast pierced concrete jally work as per design and manufacturer\"s specification including moulding etc. with stone chips and necessary reinforcement shuttering complete including fitting, fixing in position in all floors.(b) 37.5 mm thick panels |
| 56 | Page No. -212, Item No. - 19 |
| 57 | Galvanised Iron pipe outlet for water with bevelled end at outlet, supplied fitted and fixed complete including painting two coats to the exposed portion.(c) 40 mm. Dia |
| 58 | Page No. -111, Item No. -2(b) |
| 59 | Welding in M.S. structural work with gas or electric:(b) Continuous weld. |
| 60 | Sanitary & Plumbing [P.no- 69.It No. 23(A).b+ P.no-74 It. No- 24.(A).ii) |
| 61 | Supplying fitting fixing UPVC Pipe with all necessary clamps nails including making holes in walls. (110mm dia) singlesocketed 3meter length |
| 62 | c) Bend 87.5 degree(ii) 110 mm. Dia. |
| 63 | Page No. -84, Item No. - 28,A, |
| 64 | Supplying, fitting & Fixing EWC (Size- 710x370x810 mm)in white glazed vitreous chinaware of approved make supplying, fitting and fixing in position complete with necessary nut and bolts. (Model Code No.S10221114-P Trap (CRUSE SET) of CERA orequivalent.) |
| 65 | Page No. -80, Item No.-7, (i) |
| 66 | Supplying, fitting and fixing Squating plate with integral flushing in white vitreous chinaware of approved make in cement concrete (6:3:1) with jhama chips complete. (Payment of concrete will be paid seperately).(i) 450 mm X 350 mm |
| 67 | Page No. -41, Item No.- 2,(iii) |
| 68 | Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint.(i) 450 mm X 300 mm size |
| 69 | Page No. -36, Item No.- 2 |
| 70 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. |
| 71 | Page No. -84, Item No.-28,B, (b) |
| 72 | Soft Close seat cover of approved make with lid andC.P. hinges, rubber buffer and brass screws suppling, fitting and fixing complete. E W C (Model Code No. B1520118 of CERA or equivalent.) |
| 73 | Page No. -84, Item No.- 28,B, (c) |
| 74 | Supplying, fitting and fixing Stainless steel Wall Mounted Grab Bar. Load bearing capacity 150 kg, covered by Nylon surface with contour finish (for better grip) with Anti-bacterial surface complete. (Model Code No. B2210106 of CERA or equivalent.)600mm Long |
| 75 | Page No. -6, Item No. -7, b,(i), (c) (i) |
| 76 | Supplying, fitting and fixing bib cock or stop cock.Chromium plated Stop Cock (Equivalent to Code No. 513(A) & 513(B) & Model - Tropical / Sumthing Special of ESSCO or similar |
| 77 | Page No. -7, Item No.-8(b)(i) |
| 78 | Supplying, fitting and fixing push cock of heavy quality and of approved make and brand. (b) Cast iron with brass spindle (i) 15 mm |
| 79 | Page No. -6, Item No. -7, |
| 80 | Supplying, fitting and fixing bib cock or stop cock.(f) (i) Polythene Bib Cock / Stop Cock (HD) with metal inlet (EMCO / ATLAS or equivalent) 15 mm |
| 81 | Page No. -5, Item No.-5, (viii), (vi) |
| 82 | 5. Supplying, fitting and fixing gunmetal wheel valve ofapproved brand and make tested to 21 kg per sq. cm. (for water lines only).20 mm |
| 83 | 25 mm |
| 84 | Page No. -67, Item No.-18 |
| 85 | Supplying, fitting and fixing C.I. round grating.(i) 100 mm |
| 86 | Page No. -2, Item No.-1,(A),(d),(ii) & (b),(ii) |
| 87 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately)(a) For Exposed Work PVC Pipes25 mm dia. medium quality |
| 88 | 20 mm dia. medium quality |
| 89 | 15 mm dia. medium quality |
| 90 | Page No. -37, Item No.- 6,(c) |
| 91 | Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer(b) 1000 litre capacity |
| 92 | Page No. -37, Item No.- 10,(ii),(a) &(b) |
| 93 | Labour for hoisting plastic water storage tank(ii) Above 1500 litre upto 5000 litre capacity.(a) Upto 1st story from G.L. |
| 94 | Page No. -38, Item No.- 13 |
| 95 | Labour for punching hole in plastic water storage tank u |
| 96 | Sanitary & Plumbing [P.no-69.It No. 23(A).b+ P.no-74 It. No-24.(A).ii)] |
| 97 | Supply fitting & fixing of UPVC pipes (B Type) with all necessary clamps nails including making holes in wall. & fittings conforming to IS-13592-1992A) (i) Single Socketed 3 Meter Length(b) 110 mm |
| 98 | PWD P.NO-213 B fIttings |
| 99 | (ii) Plain Tee(b) 110 mm |
| 100 | x) Bend 87.5o(b) 110 mm |
| 101 | Page No. -88, Item No.-3 (7th corr. P-3) |
| 102 | Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. Note:- (i) Finished level of Septic Tank should be 400 mm. from Ground Level. (ii) Height of 50 mm. Ventilation pipe &Mosquito proof mesh, should be follwed as per IS:2470,Part- I.Payment will be made separetly on the basis of actual height based on relevant I.S.CodeFor 10 usersA) With Pakur variety. (SAIL/TATA/RINL) |
| 103 | Page No. -89, Item No.-4 (7th corr. P-4) |
| 104 | Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20 mm thick cement plastering (1:4) to inside face upto the depth of cement brick work, 15 mm thick cement plaster (1:4) on outer face from top of the well upto G.I. and 6 mm thick cement plaster (1:4) on top of the R.C.C cover slab including filling bottom 1.00 metre of inside of the well with brick metal ( 50 mm to 63 mm size) includingR.C.C cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia R.C.C manhole cover(heavy type) of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making necessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the excess earth from the premises as per direction complete in all respect with all costs of labour and materials. With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00 m inside dia.(SAIL/TATA/RINL) |
| 105 | Add 18% GST (Sl No. 1 to 48) |
| 106 | Add 1% Welfare Cess |
AI Tender Summary
Tender Timeline
Jul 23, 2024
11:30 IST
Tender Published
Tender notice published.
CompletedAug 06, 2024
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 09, 2024
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender