|
| 1 | Dismantling of wall and ceiling boards (fibre, pulp, insulation, plywood etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed. |
| 2 | Dismantling of framed work timber scantlings 40 sq.cm and over in section, in any position complete all as specified and directed |
| 3 | Dismantling of framed work of fillets, rails, posts, rafters, purlins, etc under 40 sq.cm in section complete all as specified and directed |
| 4 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed. |
| 5 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 6 | Taking down steel chowkats or frames n exc 1.5 sqm with shutters (without taking off shutters from the frame) complete all as specified and directed. |
| 7 | Demolition of reinforced cement concreteof any description of any position not otherwise specifically provided for man hole cover slabcomplete all as specified and directed. |
| 8 | Taking down steel chowkats or frames exc 1.5 sqm but n exc 4 sqm with shutters (without taking off shutters from the frame) complete all as specified and directed. |
| 9 | Taking down cement plaster on any description including scrubbing down with water and prepare to receive new plastering in wall complete all as specified and directed. |
| 10 | M&L for RCC (Nomonal mix) type B1 ( 20mm graded stone aggragate)for beam, cantilevers, bressummers lintel over 1.5 mtr span etc complete all as specified and directed. |
| 11 | M&L for PCC 1:2:4 type B-0 (12.5 mm graded aggregate ) bed or bedding layer of 25mm thick in laying floor finishes complete all as specified and directed. |
| 12 | M&L for Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 but not exceeding 0.38 sqm, over 15mm thick screed bed in CM 1:6 as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 13 | All as per Item No.13 here-in-before but on vertical surfaces such as skirting, dados and rises to steps over and including 10mm thick backing coat in CM 1:4complete etc set ,jointed in neat cement slurry and pointed to match in white or coloured cement to match complete all as specified and directed. |
| 14 | M&L for Prepolished chequered cement concrete tiles 30cmx30cmx25mm thick, set, jointed and pointed and in need cement slurry in floor with grey cement and pigment and including over screed bed or bedding layer ofmortar20 mm thick laying floor finished in cement mortor 1:6 complete all as spd and as directed. |
| 15 | M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40mm graded aggregate) and finishing cement concrete surface even and smooth without using extra cement as in plinth protection complete all as specified and directed. |
| 16 | Use and waste forformwork to sides and soffits of floor or roof beams,beam haunchings, girders, bressummers, lintels, cantilevers, shelves including suports over hangs etc.complete all as specified and directed. |
| 17 | M&Lfor mild steel TMT steel barsin reinforcement 10mm dia and overcut to length bent to shape required including crankingbindingspirally, hooping for columns hooking ends and binding with and including mild steel wire (annealed)not less than 0.9mm dia complete all as specified and directed. |
| 18 | M&L for mild steel TMT steel barsin reinforcement5mm dia and over up to 10mm dia in stirupscut to length bent to shape required including crankingbindingspirally, hooping for columns hooking ends and binding with and including mild steel wire (annealed)not less than 0.9mm dia complete all as specified and directed. |
| 19 | M&L for PCC (1:2:4) type B1 using 20 mm graded aggregate for coping including necessary formwork complete all as specified and directed. |
| 20 | Supply only water proofing compound |
| 21 | M&L for rendering 15mm thick on other than fair faces of brick work or concrete surfaces with CM 1:6 finished even and smooth withot using extra cementcomplete all as specified and directed. |
| 22 | M&L forrendering 15mm thick on fair faces of brick work or concrete surfaces with CM (1:4) finished even and smooth without using extra cement with WPC @3% by weight of cementcomplete all as specifed and directed. Note : WPC Shall be measured and paid seperately |
| 23 | M&L for Preparing new plaster surface apply two coat of distemper oil emulsion over a coat of 3 mm thick wall care putty of JK /Birla white complete all as specifed and directed. |
| 24 | M&L for preparing new plaster surface apply two coat of cement base paint over a coat ofalkali resistant primer on external walls complete all as specifed and directed. |
| 25 | M&L for pressed steel frames for doors size 125x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and directed |
| 26 | S&F for35mm thick 2nd class hardwoodfor Glazed skeleton shutters for door open rebated and prepared to receive glass gauge etc. (with sash bars) edges of framing plain, chamfered or rounded , fitted with cuts and mitred beads for securing glass etc. sizes of membersof shuttered as specified in ssr part- I section -8 clause 8.23 (b) complete all as specifed and directed. |
| 27 | M&L for 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 28 | S&F for Steel ventilators with centre hung shutter including two pair of bress cup pivots catch sprin and pully wheel complete all as specified and as directed. |
| 29 | S&F for Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed |
| 30 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessaryfilling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and thedirections of Enginee-in Charge. |
| 31 | S&F for 4.8mm thicksheet glass of ordinary quality and glazing with oil putty and fixed to aluminium shutters in square n.exc 0.5Sqm in each pane complete all as specified and directed. |
| 32 | S&F forAluminium anodised grill (anodised trasparent or dyed torequired shade according to IS:1868 with minium anodic coating of grade AC15) of approved design/ pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per reqirement and direction of Engineer-in-Charge |
| 33 | S&F for 375mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed |
| 34 | S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 35 | M&L for preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink preimer complete all as specified and directed |
| 36 | M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed |
| 37 | S&F for mild steel butt hinges 100mm size of medium weight complete all as specified and directed. |
| 38 | S&F for 200mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. |
| 39 | S&F for 150 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. |
| 40 | S&F for 150 mm long Extruded aluminium alloy handles, fabricated type., anodised complete all as specified and directed. |
| 41 | M&L for 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed |
| 42 | S&F for Harrison rails, mild steel, chromium plated with fixing brackets, stops,rollers etc, Complete all as specified and directed. |
| 43 | S&F for Steel work in tubular section as in post including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed. |
| 44 | S&F mild steel rolled sections as in roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle,channel or flat sections) including distance pieces, cleats ( Fe 410-W (Gde E-250) quality A) all as specified and directed. |
| 45 | S&F for rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates ( Fe 410-W (Gde E-250) quality A)all as specified and directed. |
| 46 | S&F for plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment using Fe 410 -W (Gde- E- 250) quality- A with reveted bolted or welded attachment complete all as specifed and directed. |
| 47 | M&L for mild steel screw bolts (machine made) 5 to 10mm dia of neck with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed and to be fitted with washers and one hexagonal or square nut n exc 5 cm longcomplete all as specifed and directed. |
| 48 | M&L for mild steel screw bolts (machine made) 11 to 15 mm dia of neck with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed and to be fitted with washers and one hexagonal or square nut exc 22.50 cm and n,exc 30cm longcomplete all as specifed and directed. |
| 49 | S&Ffor Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specifed and directed. |
| 50 | S&F for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specifed and directed. |
| 51 | S&F for frame work for suspended false ceilingAluminium snap grid frame work exposed ceiling suspension system of grid size 600mm/600mm with main runner 38mmx24mm, cross tee 29mmx24mm and wall angle 24mmx24mm including 6 mm dia GI/MS bar hanger fixing with steel dash fastner or iron purlins from the roof with adjustment clip providing position for light fixture etc all as specified and directed. |
| 52 | S&F for false ceiling of Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium frame work with screw of size 595mm x 595mmx4mm thick fixed on Aluminium snap grid, complete all as specified and directed. |
| 53 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in hard/dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 complete all as specified and directed. |
| 54 | Taking down unserviceable old existing service /submain wiring of any size complete all asspecified and directed |
| 55 | Dismantling and taking down of unserviceable distribution boards alongwith MCB TPN complete all as specified and directed |
| 56 | Taking down unserviceable old existing service /submain wiring of any size complete all asspecified and directed |
| 57 | M&L forpoint wiring in PVC concealedconduit as required at site of size confirming to IS 2079-1973 medium grade with PVC insulated unsheathed multistranded copper conductor cable (FRLS) 1.5 sqmm nominal cross sectional area 1100 volts grade with all fittings such as elbows, bends, junction boxes, saddles including PVC board (ISI Mark) and screws and rawal plugs including 1.5 sqmmPVCinsulated & unsheathed copper conductorcable as earth wire and connected to light/fan & common earth dollywith necessary copper thimbels all as specified and directed for One light/bell point controlled by one ,one wayswitchMakke:PVC conduit pipe including accessories. Make :Kalinga/ Harish/Polypac/Plaza/Gaurav andMake of PVC Copper wire : Plaza/Polycab/RR Kabeel /Plaza /Havells |
| 58 | All as per item No 57 above but one socket outlet 5 pin 5/6 Amps onindependent board controlled by one, one way switch. |
| 59 | All as per item No 57 above but one socket outlet 5 pin 5/6 Amps onsame board with other one, one way switch. |
| 60 | All as per item No 57 above but for socket out let, 15/16 Amps on independent board with 4 Sqmm size cable and 4 Sqmm for continuty earth wire connected tocommon earth dolly all as specified and directed. |
| 61 | S&F in replacement switch pianoflush type 5/6 Amps single pole one way all as specified & directed. Make : Anchor/Legrand/HPL/Cona |
| 62 | S&F in replacement switch piano flush type 15/16 Amps single pole one way all as specified & directed. Make : Anchor/legrand/HPL/Cona |
| 63 | M&Lin replacement socket out let5 pin 5/6 Amps all as specified and directed.Make : Anchor/legrand/HPL/Cona |
| 64 | S&Fin replacement socket out let2-in-1, 6 pin 5/6 & 15/16 Amps all as specified and directed.Make : Anchor/legrand/HPL/Cona |
| 65 | S&Fin replacement ceiling rose 2/3 terminals 65x25 mm diapoly carbonate isolated all as specified and directed.Make Anchor/legrand/HPL/Cona |
| 66 | S&F in replacement lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings. Make : Anchor/legrand/HPL/Cona |
| 67 | S&F 9 watt LED bulb cool day light, 230/240V AC supply all as specified and as directed. Make : CG/Philips/Bajaj/Anchor |
| 68 | S&F in replacementLED tube light fitting bright18 wattslim elegant design. and including connected with 3 core 23/0.0076 insulated copper wire from celing rose to fittting connector all as specified and directed. Make : Philips/Baja/CG/Havells |
| 69 | S&F LED bulk head light fitting 10W luminaries including LED driver holder connecting up with three core flexible copper conductor cable suitable size complete all as specified |
| 70 | S&F building security light fitting complete with 35 watt LED type IP 66 pressure die cast aluminium housing and heat resistance toughened glass with frame protection and better optics for unifom distribution etc incuding GI pipe (light grade) mounting bracket of size 32 mm dia and 1.20 m long fixed to wall with and incduding nut, bolts and G clamps of size 50 x 6 mm as required complete with twin core copper conductor cable 1.5 sgmm from ceiling rose to fittings complete all as specified and direct |
| 71 | S&F MCB DB TPN, 4 way 415 volt , double door type MCB DB suitable for mounting incoming and outgoing MCBS double pole/ single pole complete all as specified and direct |
| 72 | S&F MCB DB SPN, 8 way 240 volt, double door type MCB DB suitable for mounting incoming and outgoina MCBs doubie pole/ single pole complete all as specified and directed. |
| 73 | S&F6 to 40 Amp MCB SP with thermal over load as wel as magnetic short circuit tripping device with quick break trip free mechanism, robust design and terminals having heat resistance moulding complete all as specifed and directed. |
| 74 | S&F 63 Amp MCB TPN with thermal over load as well as magnetic short circuit tripping device with quick, breal trip free mechanism, robust design and terminals having heat resistance moulding complete all as specified apd directed. |
| 75 | S&F 40 Amp MCB DP with thermal over load as well as magnetic short circuit tripping device with quick. breal trip free mechanism, robust design and terminals having heat resistance moulding complete all as specifed and directed. |
| 76 | S&F ceiling fan 1200 mm sweep complete with blades, down rods, electronic regulator and accessories, 230v Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushiess direct curent motor (BI Do complete all as specified and directed. |
| 77 | M&L for sub main wiing in PVC casing and caping of reqd size 2 x 6.0 Sqmm PVC insulated multistrand copper conductor with 1 x 4.0 Sqmm PVC insulated multistrand copper conductor as earth continuity wire complete all as specified and directed. |
| 78 | Supply, laying. jointing and testing in replacement of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded alumin conductor of size 16 sqmm 4 core all as per IS, specified & directed. |
| 79 | M&L in replacement of earthing complete with galvanished steel earth plate electrode size 600X600X6mm thick burried directly in ground vertically toa depth not less than 2.25m below nomal ground level with top edge of earth plate not less than 1.5m below normal ground level connected to and incd Gl earth lead wire 4mm dia by means of bolts ,nuts, check nuts & washers of galvanised iron and connected to test point all as shown in electrical plate No 3 of SSR part I-2009 and as specified or indicated and testing on completion incl excavation and earth work in any type of strata available at site PCC (1:3:6)type C-1 earthing chamber .pre cast RCC slab 50 mm thick in cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate reinforced with welded steel wire fabric (XPM) weight not less than 4 kg/sqm funnel with Gl watering pipe of 20 mm bore medium grade ,wire mesh and lugs ,GI protection pipe of 15 mm borelight grade up to 7.5 mtr long etc complete all as specified and directed. NOTE:- GI earth wire and protection pipe beyond 7.5 mtr will be measured and paid separately |
| 80 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 Sqmm 3.5 core. |
| 81 | Supply andinstallation, connecting eclectically & commissioning of LT feeder pillar box outdoor type of size 0.90 x 0.60 x 0.50 Mtr size factory fabricated made out of MS sheet of thickness 3.15 mm front door openable with locking arrangement mounted on angle iron legs made out of angle iron of size 40x40x6mm, 1.5 mtr long, 1.0 mtr above ground level and 0.50 mtr embedded in PCC blocks of size 0.30x0.30x0.50 mtr- 04 Nos duly painted with two coats of synthetic enamel paint over a coat of red oxide complete with 200 amps rated aluminium bus bar suitable for 3 phase 4wire supply system duly drilled holes and makingall cable connection with proper thimbles mounted on epoxy based post insulators and one MCCB 200 Amps 4 pole 415 Volt, 35 KA of make : Legrand/Havells/L&T complete all as required at site. |
| 82 | S&F, 4 pole MCCB of capacity 200 Amps, 415 Volts, 50 Hz, 3 phase breaking capacity 35 KA with adjustable thermal megnatic release type - 01No. |
| 83 | Excavation in trenches in hard/dense soilnot exceeding 1.5 mtr width and not exc 1.5 mtr deepfor laying of pipe etc and getting out allas specified. |
| 84 | Returning, filling including spreading levelling watering and well ramming in layers not exceeding 25 cm thick hard soil all as specified and directed by Engr-in-charge. |
| 85 | Removing excavated soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed |
| 86 | Dismantaling and taking outoldexistingunserviceable GI pipe ofsize 80 mm dia fromtrenches/ under floor, roads, paths or from walls/poles/ducts all as specified and directed |
| 87 | S&F 80 mm bore GI tubing medium gradewith all fittings, laid in trenches,duly welded, nuts & bolts gaskets and all accesories including union, nipple, socket, elbow or reducer etc required for completion of work all as specified and directed. Make : Jindal/Tata/Prakash Surya.(Note:- Rate for carring of Generator,Weding Machine and transportation cost for pipes at source deemed incuded in item rate. Excavation & earth work shall be measured and paidfor separately under respective item of this schedule) |
| 88 | Dismentaling and taking outoldexistingunserviceable GI pipe ofsize 80 mm dia fromtrenches/ under floor, roads, pathsand relayingduly welded, nuts & bolts gaskets and all accesories including union, nipple, socket, elbow or reducer etc required for completion of work all as specified and directed.(Note:- Rate for carring of Generator,Weding Machine and transportation cost for pipes at source deemed incuded in item rate. Excavation & earth work shall be measured and paidfor separately under respective item of this schedule) |
| 89 | M&L for cleaning of (20000 ltr Gravel filter tank ) washingthe following filter media in the filter bed duly cleaned and washed with 5% concentrated solution of NaOH complete including clening of tank as per standard procedure all as directed by Engr-in charge(a) Filter gravels (pebbles) 1.5\"\" -2\"\" -1.4 Cum (b) -do- but size 3/41.5\"\"-0.9Cum(c ) -do- but size 1/2\"\"-3/4\"\" - 0.3 Cum (d) -do- but size 1/4\"\" - 3/8\"\"-0.3 Cum(e) -do- but size 1/8\"\" - 1/4\"\"- 0.5 Cun |
| 90 | M&L in replacement of 3mm thick MS sheet top cover over the sluice valve pit/filtration tank, made with MS angle iron/channel and MS sheet with locking arrangement incl pad lock andproviding suitable lifting handle for each voer/valve pit including cutting, drilling, bending etc complete all as specified at site |
| 91 | M&L in replacement of Gun metal globe or gate valves, with iron wheel head , screwed both ends for iron pipes of size 80 mm diawith washers ,all as specified and directed.Make : Kirloskar/leader/Kartar. |
| 92 | Supply and install of cast iron sluice valve of size 80 mm bore class-I PN-1:6 with gun metal spindle both end flanged complete with all fitting all as specified and directed by Engr in Charge. Make : Kirloskar/leader/Kartar. |
| 93 | M&L for cleaning of complete water tank of 10000 to 25,000 gln capacity with chamber complete as specified and directed by Engr-in-Charge, comprising the following works :- (a) Dewatering of left out water from the tank manually or by pumping out throgh pump set (b) Taking out complete sludge/mud from the tank and removing/storing the same at low level are ermarked by Engr-in-Charge within 50 m radius (c ) Cleaninginner surface of wall and bottom of tank with the help of wire brushes, scrapper and broom for cleaning of sludge from walls/floors (d)Washing of inner walls of tank by bleaching powder solutiion (e)Repairing of unserviceable angle/MS Sheet of sedimentation tank with welding work where necessary complete all as per site requirement (f)The empty sedimentation tank shall be first cleaned with fresh water twice and ther after cleaned with fresh water sterililsed with 2% solution of potassium permagnate and writing location, capacity and date of cleaning with white paint firm and hand written over a black plate with synthetic enamel paint etc complete for entire satisfaction of Engr-in-Charge |
| 94 | S&F in replacement of galvanised iron flange on existing pipe of 80mm bore (02 Nos in each pipe) with nuts, bolts and washers complete all as specified and directed. |
| 95 | M&L for cement concrete Type C2 1:3:6 (40mm graded aggregate) in foundations, filling and mass concreterequired at site all as specified and directed. |
| 96 | Construction of valve pit chamber having internal dimentions 1050 mm x1050mmx 900 mm using PCC 1;3;6 ) 40 mm stone aggregate .foundation 15 mm thich, 23 mm thick wall in CM(1;4) 10 mm thick rendring from MS top sheet cover with locking arrangementMS angle frame made out of 60x60x6 mm thick angle iron incl painting all as specified and directed |
