Tender For Fabrication Erection Work, The Work Of Cutting And Removing The Street Pipe Line From 1/2 To 12 Inches And Installing The New Pipe At Its Place. Fabricating And Fitting New Neck Bands From 1/2 Inch To 12 Inches, Nipples, Caps, Tees, Rings. R, kaimganj-Uttar Pradesh

Tender For Fabrication Erection Work, The work of cutting and removing the street pipe line from 1/2 to 12 inches and installing the new pipe at its place. Fabricating and fitting new neck bands from 1/2 inch to 12 inches, nipples, caps, tees, rings. Refurbishment of 1/2 inch to 12 inch diameter coils The work of fabricating and installing new flanges of 6 to 12 inches diameter. Work of cutting and removing 14 to 40 gully pipe line and fabricating a new one and installing it at the same place. Cutting and removing 14 inch to 40 inch neck band nipple, case, tee, ringer and fabricating a new one and installing it in place. The work of making and installing new gully flanges of 14 inches to 40 inches diameter. Newly fabricate the round square tank installed in the mill and install it in place and put all the connections in place. 10 to 01 meter dia. Above 01 meter to 03 meter. Strengthening with heavy structures at various places. Strengthening with light structure at various places. Strengthening and repairing throat platform at various places. Making/replacing manholes at various places. Removal of old / sore cones installed at various places and installation of new ones from 8/10 mm plate. 10 to 01 meter dia. Above 01 meter to 03 meter. The gully casing of the fans at different places is 6/8 mm. The act of fabricating a new plate. Making and installing catchers at various stations. (including all attachments) Patching broken equipment at various stations. Cane Carrier / Bagasse Elevator / R.B.C. Replacement of corroded trough/side plate. Removing street side plates from various places and installing new plates. Cane Carrier / Bagasse Elevator / R.B.C. Removing the runner base and installing a new runner base. Cane Carrier / Bagasse Elevator / R.B.C. Removing the runner and installing a new runner. Removing the damaged T-iron and angle iron of the cane carrier and reinstalling it by straightening the crooked part. Removing the neck part of the suit from different places and fitting a new one. Chevron grooving of new rollers of the mill. To do chevron grooving of old rollers of the mill. Remove the gully partition plates of the juice box at the top and bottom of the juice deaerator by 10/12 mm. Make a new one from the plate and install it. Installing ribs in the top and bottom partitions of the juice heater. Shave-all repair of quad. Removal of old gutters installed at various places and installation of new gutters. Remove the old se-al from pan and quad and install new one. Reinstalling the umbrella fitted inside the pana by making a new one and removing the old one. Replacement of the mascot receiving Kistlyzers ribbon arm. Making the separator of a mascot machine. Removing the hopper cover and installing a new one. Making and installing separators for continuous machines. Removing the tubes of Quad Juice Heater, Dynamic Juice Heater, expanding them by installing new tubes and hydraulically testing them and giving a satisfactory trial. Size 42 mm Removing the tubes of the pan, installing new tubes, expanding them and hydraulically testing them and giving a satisfactory trial. Size 96 mm Removing the stuck ducting from both the boilers and installing ducting from new or old plates. Vayalar no. Removing the gully plate in front of 1 and 2 and installing a new plate on the roof. Removing the damaged Vyler damper and installing a new one. Making bagasse suit and applying it. Replacement of juice over flow box of clarifier. Making and installing motor pumps at various places as per requirement. Replacement of sulfur mud 6 inch dia cooling pipe. A. Removing the monitor casing from the old machines and installing it again. Making/replacing manholes at various places. Refurbishing/replacing the internals of the pan catcher. Reinstalling/replacing the hood of a cane cutter. Remove the old bottom plate of the lowest compartment of the clarifier and install a new plate on it after installing an angle trap as per the instructions and provide satisfactory water dial. Reinstalling the stirrer of the clarifier as new and providing satisfactory operation. A. Removing the shaft of a pug mill and removing the old bushes on both sides and fitting new ones. Removing and refitting the shaft of the Brown Sugar Magma Mixer and installing a new bush. Reinstalling the connecting rod of the damper by making a new one. Making and installing new catcher strainer. Removing the old rail line of the unloader branch and fitting the new rail line satisfactorily and doing water level. Reinstalling the old rail line of the unloaders bridge and fitting it and checking water level etc. Removal of old / narrow channels of 3 inches to 10 inches diameter installed at various places and installation of new ones as per requirement. Cutting and straightening old plates installed at various places as per requirement. Removing the old scrubber on sulfur soil and making it from 8/10 mm plate and making all the connections. Removing the dead plate (including support) of the top chamber of the clarifier, the worn shell and top cover plate and fitting a new plate and providing a water proof dual. Rebuilding, aligning and dialing the hopper driving end. Making and installing the top cover of the centrifugal machine. Making an arm and installing it on the shaft of a pug mill. Making and applying sulfur mud scrubbers/bottle jackets. Prepare and apply IM type sulfur soil. Cutting out the corroded part of the vapor cell and fitting it with a new plate. Modifying the shell of juice sulfiter by reducing its diameter as per the drawing. Old DSM Removing the skin, fitting a new one and replacing its neck frame. Removal of jammed mixed juice spreader installed on the mill and Make a new one and install it as per the instructions. Cleaning and giving hydraulic testing like all the tubes of Daciant deaerator. Making the bent trolley of can unloader.

INR 590 /-

INR 10000.0 /-

Refer document